Welding: Principles and Applications (MindTap Course List)
8th Edition
ISBN: 9781305494695
Author: Larry Jeffus
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 20, Problem 23R
How much metal is left if 1/8 in. is ground off a 5/16-in.-thick plate?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Please answer ASAP and include the FBDs. Thank you!
Parts a through h please. Thank you!
the parts
Answer the following
elating to the drawing in figure (3a):
1- What is the name of the component?
2- What size is the oil hole? How far is the oil hole from the edge of the
cylinder?
3- How many holes have to be drilled $12?
4- What is the overall height of the finished item?
5- What welding is specified by the symbol marked A?
6- How many pieces are used to make this item?
7- What sizes of welds are used? How thick is item 2?
8- What are the general tolerances? How many surfaces are machine finished?
63 all hole -4 holes 012
BO
3²8
44.00
5 ROUND BAR
MINOR WEDS
Section A-A
6
PARTS LIST
425x6
MS
70xBx56
MS
3 ROUND BAR
BEOXDO
MS
2 MAIN WEB
200xBx35 MS
1 BASE PLATE
200x400x120 MS
ITEM
DESCRIPTION
SIZE
MATL
AND ENGINEERING
DRAMA
FRACED
CHECKED
TAFE:
K BERYCES CONSORTIA
TITLE
SHAFT SUPPORT BEARING
SCALE
12
02-MF 1- MY 98
F
TYP
140
200
←
All welde et unicee indicated otherwise
First
CHANGE
AMENDMENTS
NOTE:
70/98
ISSUE DATE
-A
LZ DO
ECH BY CKD
825
UN ES NOTED OTHERANSE
TOLERANCES…
Chapter 20 Solutions
Welding: Principles and Applications (MindTap Course List)
Ch. 20 - What are two ways math is most commonly used in...Ch. 20 - What is the two-letter abbreviation for the metric...Ch. 20 - List factors that affect the cost of producing...Ch. 20 - List three examples of whole numbers.Ch. 20 - List three examples of decimal fractions.Ch. 20 - List three examples of a mixed unit.Ch. 20 - List three examples of fractions.Ch. 20 - Add the following angles: a. 3050+205 b. 2525+6245Ch. 20 - Subtract the following angles: a. 45481020 b....Ch. 20 - Using the Pythagorean theorem, find c if a=6 and...
Ch. 20 - Sketch a right triangle, equilateral triangle, and...Ch. 20 - Find the area of the following: a. Square that is...Ch. 20 - Find the volume of the following: a. 5 cube b. 10...Ch. 20 - What would the labor cost be if 20 hours were...Ch. 20 - What is the first step in the sequence of...Ch. 20 - If you need two pieces of pipe—one must be 15 ft...Ch. 20 - How many total feet of metal stock would you need...Ch. 20 - How many total feet of metal stock would you need...Ch. 20 - How many feet of scrap pipe will you have left...Ch. 20 - How much scrap pipe will you have once you cut out...Ch. 20 - When the denominators of two fractions to be added...Ch. 20 - How thick will the finished part be if two pieces...Ch. 20 - How much metal is left if 1/8 in. is ground off a...Ch. 20 - What is a dimensioning tolerance?Ch. 20 - What is the minimum and maximum length a part can...Ch. 20 - Give examples of welding applications where angles...Ch. 20 - Write the Pythagorean Theorem formula for a right...Ch. 20 - What is the name of a triangle where all three...Ch. 20 - Why is it important to know the perimeter...Ch. 20 - In what welding applications might you need to...Ch. 20 - List examples of fixed and variable costs that...Ch. 20 - List examples of overhead costs that a welding...Ch. 20 - When estimating weld cost, what weld joint design...Ch. 20 - When a weld is oversized, what joint failure...Ch. 20 - How does the bevel angle in a groove weld affect...Ch. 20 - What is the cross-sectional area of a V-groove...Ch. 20 - What is the cross-sectional area of a fillet weld...Ch. 20 - What two amounts must be multiplied to determine...Ch. 20 - How many pounds of steel electrode are required to...Ch. 20 - Not every pound of electrode filler metal used is...Ch. 20 - What does it mean if an electrode has a 50...Ch. 20 - What is the meaning of the term deposition rate?Ch. 20 - What factor is not included in the deposition...Ch. 20 - Why do flux cored wires have a higher deposition...Ch. 20 - If a welding project has a 45% operating factor,...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- How thick will the finished part be if two pieces of metal are welded together if one is 3/4 in. thick and the other is 5/16 in. thick?arrow_forwardHow many total feet of metal stock would you need if one piece is 12 ft 5 in. long and the other is 7 ft 3 in. long?arrow_forwardwith complete solution and with figure if possiblearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Material Properties 101; Author: Real Engineering;https://www.youtube.com/watch?v=BHZALtqAjeM;License: Standard YouTube License, CC-BY