Welding: Principles and Applications (MindTap Course List)
8th Edition
ISBN: 9781305494695
Author: Larry Jeffus
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 20, Problem 12R
Find the area of the following:
a. Square that is
b. Circle with a
c. Equilateral triangle with a
d. Oval that is
e. Parallelogram with a
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
An equilateral triangle of 35 mm side has an edge in the HP which is inclined at 40° to the VP. The plane itself is inclined at 50° to the HP. Draw the projections of this plane.
y
4+B
5+C
1.Find The size of the area number 1 (triangle)
2.Find The center of the numbered area is 1 x-axis (X1).
3.Find Center of area number 1, y-axis (Y1).
4.Find Size of area number 2 (square)
3+A
2)
Finding the third projection
Chapter 20 Solutions
Welding: Principles and Applications (MindTap Course List)
Ch. 20 - What are two ways math is most commonly used in...Ch. 20 - What is the two-letter abbreviation for the metric...Ch. 20 - List factors that affect the cost of producing...Ch. 20 - List three examples of whole numbers.Ch. 20 - List three examples of decimal fractions.Ch. 20 - List three examples of a mixed unit.Ch. 20 - List three examples of fractions.Ch. 20 - Add the following angles: a. 3050+205 b. 2525+6245Ch. 20 - Subtract the following angles: a. 45481020 b....Ch. 20 - Using the Pythagorean theorem, find c if a=6 and...
Ch. 20 - Sketch a right triangle, equilateral triangle, and...Ch. 20 - Find the area of the following: a. Square that is...Ch. 20 - Find the volume of the following: a. 5 cube b. 10...Ch. 20 - What would the labor cost be if 20 hours were...Ch. 20 - What is the first step in the sequence of...Ch. 20 - If you need two pieces of pipe—one must be 15 ft...Ch. 20 - How many total feet of metal stock would you need...Ch. 20 - How many total feet of metal stock would you need...Ch. 20 - How many feet of scrap pipe will you have left...Ch. 20 - How much scrap pipe will you have once you cut out...Ch. 20 - When the denominators of two fractions to be added...Ch. 20 - How thick will the finished part be if two pieces...Ch. 20 - How much metal is left if 1/8 in. is ground off a...Ch. 20 - What is a dimensioning tolerance?Ch. 20 - What is the minimum and maximum length a part can...Ch. 20 - Give examples of welding applications where angles...Ch. 20 - Write the Pythagorean Theorem formula for a right...Ch. 20 - What is the name of a triangle where all three...Ch. 20 - Why is it important to know the perimeter...Ch. 20 - In what welding applications might you need to...Ch. 20 - List examples of fixed and variable costs that...Ch. 20 - List examples of overhead costs that a welding...Ch. 20 - When estimating weld cost, what weld joint design...Ch. 20 - When a weld is oversized, what joint failure...Ch. 20 - How does the bevel angle in a groove weld affect...Ch. 20 - What is the cross-sectional area of a V-groove...Ch. 20 - What is the cross-sectional area of a fillet weld...Ch. 20 - What two amounts must be multiplied to determine...Ch. 20 - How many pounds of steel electrode are required to...Ch. 20 - Not every pound of electrode filler metal used is...Ch. 20 - What does it mean if an electrode has a 50...Ch. 20 - What is the meaning of the term deposition rate?Ch. 20 - What factor is not included in the deposition...Ch. 20 - Why do flux cored wires have a higher deposition...Ch. 20 - If a welding project has a 45% operating factor,...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- (i) The Area of Triangle (a1) in mm2 is (ii) The Area of circle (a2) in mm2 is (iii) x1 isarrow_forwardQ.3) For the machine element shown, find the coordinates of the center of volume. 1 in. 2 in. 2 in. 3 in. 2 in. r=1.25 in. r=1.25 in. 0.75 in. 2 in. 2 in.arrow_forwardAdd the vectors using triangle rule or parallelogram rule Karrow_forward
- Find the volume of the following: a. 5 cube b. 10 of 8 pipearrow_forwardIf the area of a triangle is 480 sq mm and the height is 15.2 mm what is the basearrow_forwardQuestion 3) The length L is given as L=34 m on the plate in the figure. According to this;Question 3-A) Find the X coordinate of the geometric center of the plate. (Enter your result without writing m units. Write at least three digits after the comma.)Question 3-B) Find the Y coordinate of the geometric center of the plate. (Enter your result without writing m units. Write at least three digits after the comma.)arrow_forward
- Solve for rectanglearrow_forward9. Find the volume of a hollow sphere if it's inside diameter is 1 inch and the outside diameter 5 inches. Page #arrow_forwardGiven a triangle with side b = 98.7 units, side c = 65.4 units and angle A = %3D 27°45'. Which of the following is the measure of side a to the nearest thousandths? O 51.083 u 39.739 u 48.101 u 50.928 uarrow_forward
- 2. For the plan area shown, determine the location of the Centriod. Use you're the last two digits of your ID for the missing length x mm. ID:88 The following table facilitates the calculations for the required data 5 mm 10 mm 3 mm 10 mm x mmarrow_forwardSolve just point 4 please!arrow_forward4. What is the complement of a 72°21′47″ angle?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Mechanical Engineering: Centroids & Center of Gravity (1 of 35) What is Center of Gravity?; Author: Michel van Biezen;https://www.youtube.com/watch?v=Tkyk-G1rDQg;License: Standard Youtube License