Applied Statics and Strength of Materials (6th Edition)
6th Edition
ISBN: 9780133840544
Author: George F. Limbrunner, Craig D'Allaird, Leonard Spiegel
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 10, Problem 10.20SP
During a tensile test of a steel specimen, the strain at a stress of 35 MPa was calculated to be 0.000 170 (point A). The strain at a stress of 134 MPa was calculated to be 0.000 630 (point B). Determine the modulus of elasticity for this material using the slope between these two points. Calculate the expected stress that would correspond to a strain of 0.000 250. The proportional limit is 200 MPa.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Tensile test specimens are extracted from the "X" and "y" directions of a rolled sheet of metal. "x" is the rolling direction, "y" is
transverse to the rolling direction, and "z" is in the thickness direction. Both specimens were pulled to a longitudinal strain =
0.15 strain. For the sample in the x-direction, the width strain was measured to be ew= -0.0923 at that instant. For the sample in
the y-direction, the width strain was measured to be gw=-0.1000 at that instant.
The yield strength of the x-direction specimen was 50 kpsi and the yield strength of the y-direction specimen was 52 kpsi.
Determine the strain ratio for the x direction tensile test specimen. Determine the strain ratio for the y-direction tensile test
specimen. Determine the expected yield strength in the z-direction. Give your answer in units of kpsi (just the number). If the
sheet is plastically deformed in equal biaxial tension (a, = 0, to the point where & = 0.15, calculate the strain, 6, that would be
expected.
Problem F2
stress (ksi)
130
120
110
100
90
80
70
60
50
40
30
20
10
0
0.000 0.025 0.050
0.075 0.100 0.125 0.150 0.175
strain (in/in)
Above you will find the experimental
stress-strain diagram of 1045 steel.
Calculate the permanent set if a
cylindrical specimen with a diameter of
2 in is loaded to the ultimate stress and
then unloaded. Provide your answer in
units of in/in with 3 significant figures
after the decimal. The elastic modulus
of 1045 steel is 29,000 ksi.
O 0.6%
19%
If an isotropic material has a Young's modulus of 85 Gpa and a Poisson's ratio of 0.25, calculate its shear modulus.
Select one:
O G = 29 Gpa
O G = 34 Gpa
G = 25 Gpa
O G= 77 Gpa
O G= 46 Gpa
If a rubber material is deformed as shown in the following figure, determine the normal strain along diagonal BD.
C
2 mm
4 mm
EN
DO O
Chapter 10 Solutions
Applied Statics and Strength of Materials (6th Edition)
Ch. 10 - A 916 - in. - diameter steel rod is tested in...Ch. 10 - A concrete cylinder 150 mm in diameter was tested...Ch. 10 - Prob. 10.3PCh. 10 - The data from the tension test of a steel specimen...Ch. 10 - An 18-in.-long titanium alloy rod is subjected to...Ch. 10 - ASTM A36 steel rods are used to support a balcony....Ch. 10 - A 450-mm-long AISI 1020 steel rod is subjected to...Ch. 10 - A tension member in a roof truss is composed of...Ch. 10 - A short, solid, compression member of circular...Ch. 10 - A main cable in a large bridge is designed for a...
Ch. 10 - Test results of a steel specimen indicated an...Ch. 10 - A concrete canoe in storage is supported by two...Ch. 10 - A load is applied to a rigid bar that is...Ch. 10 - Prob. 10.14CPCh. 10 - Write a program that will allow a user to input...Ch. 10 - A 12 - in. - diaiíct.cr structural nickel steel...Ch. 10 - Compute the modulus of elasticity of a copper...Ch. 10 - A concrete cylinder 6 in. in diameter was tested...Ch. 10 - An aluminum bar 2 in. by 12 - in. in cross section...Ch. 10 - During a tensile test of a steel specimen, the...Ch. 10 - A 12.5-mm-diameter steel rod was subjected to a...Ch. 10 - Prob. 10.22SPCh. 10 - A standard steel specimen having a diameter of...Ch. 10 - 10.24 A tension member in a structure is composed...Ch. 10 - A pair of wire cutters is designed to operate...Ch. 10 - Calculate the end bearing length required for a...Ch. 10 - Design a 3-m-long rod subjected to a tensile load...Ch. 10 - The collar bearing shown is subjected to a...Ch. 10 - A 10-ft-long steel member is subjected to a...Ch. 10 - Two steel bars A and B support a load P, as shown....Ch. 10 - Prob. 10.31SP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Problem 2: A specimen of steel having an initial diameter of 0.503 in was tested in tension using a gauge length of 2 inches. The following data were obtained for the tension. Plot the stress strain data and determine the modulus of elasticity, and the yield strength of the material. Elastic State Load P Ibf Elongation in 1 000 0.0004 2 000 0.0006 3 000 0.0010 4 000 0.0013 7 000 0.0023 8 400 0.0028 8 800 0.0036 9 200 0.0089arrow_forwardQuestion 3: Please refer to the metal bar and its cross-section shown below. Two strain gages a and and b are attached to the bar as shown; note that 3 is the angle of their orientation with the x-axis. Assume: the Young's modulus of the metal = 16, 500 ksi; the Poisson's ratio of the metal = 0.33; P, = 13 kips; P, = 20 kips; d = 4.0 in.; t = 0.75 in.; L = 18 in.; and B = 40°. Determine the strains expected in the strain gages. 가 2 B b a H Ps N H y darrow_forwardA 5 mm diameter aluminium alloy test bar is subjected to a load of 500 N. If the diameter of the bar at this load is 4 mm, the true strain is 1. 0.56 2. 0.22 3. 0.25 4. 0.45arrow_forward
- Determine the elastic tensile load "F" that acts on mild steel specimen of Diameter 9 mm & Modulus of Elasticity 201 GPa. It is found that the specimen has undergone an extension of 1 mm due to the elastic load "F". Also, determine the length "L" of the specimen, if the strain- induced due to the load "F" on the specimen is 3.6 x 10-³. Solution Cross-sectional Area, A (in mm²) = 63.617 One possible correct answer is: 63.617251235193 Tensile Stress, (in N/mm²) 723.6 One possible correct answer is: 723.6 Tensile Load, (in N) = = 46033.261 One possible correct answer is: 46033.442993786 Length of the Specimen (in mm) 4.366 X One possible correct answer is: 277.77777777778arrow_forwardDetermine the elastic tensile load "F" that acts on mild steel specimen of Diameter 5 mm & Modulus of Elasticity 207 GPa. It is found that the specimen has undergone an extension of 1.2 mm due to the elastic load "F". Also, determine the length "L" of the specimen, if the strain-induced due to the load "F" on the specimen is 3 x 10-³. Solution Cross-sectional Area, A (in mm²) = Tensile Stress, (in N/mm²) = Tensile Load, (in N) = Length of the Specimen (in mm)arrow_forwardA torsion test shows that the shear modulus of an aluminum specimen is 4.60 x 10^6 psi. When the same specimen is used in a tensile test, the modulus of elasticity is found to be 12.2 x 10^6 psi. Find Poisson's ratio for the specimen. * 0.95 0.30 0.40 0.33arrow_forward
- 1-A round member having a diameter of 3cm experience an axial load of 10KN. Two strain gauges are mounted on the member, one measuring an axial strain of 600 micro-strain and the other measuring a lateral strain of -163 micro-strain. The modulus of elasticity in GPa is Choose... The Poisson ratio is Choose... + The stress in MPa is Choose... + Next pagearrow_forwardTwo round rods, one of steel, the other of brass, are joined end to end. Each rod is 0.5 m long and 2 cm in diameter. The combination is subjected to a tensile force of 5000 N. Find the strain in each rod. Young's Modulus of Steel use 20×10¹⁰ Pa, of brass use 10×10¹⁰ Pa. Find the elongation of each rod.arrow_forwardNatural rubber is tested in tension to a maximum extension ratio of λ = 3. The Mooney-Rivlin constants for this material are found to be C1 = 0.069 MPa and C2 = 0.125 MPa. Plot the corresponding uniaxial stress vs. extension ratio behavior over the tested range. Derive an expression for the slope of the function, then determine the secant and tangent moduli at 100% strain.arrow_forward
- 1. A bicycle wheel is assembled with each spoke pre-tensioned to a tensile force of 95 lbf. The diameter of each spoke is d = 0.0787 in. After the wheel is assembled, a strain gauge is applied to a representative spoke so that the gauge reads zero strain in the pre-tensioned condition. The figure below shows one cycle of strain readings as the wheel rotates through one revolution in use. Zero degrees corresponds to the spoke being between the hub and the ground (i.e., at the six o'clock position). 50 -50 -100 -150 -200 -250 -300 -150 -100 -50 50 100 150 Spoke position in degrees He, microstrainarrow_forwardA metal wire is 2.5 mm diameter and 2m long. A force of 12 N is applied to it and it stretched 0.3 mm. Determine the stress, strain and tensile modules of the wire.arrow_forwardA specimen of titanium alloy is tested in torsion and the shear stress–strain diagram is shown in Fig.a. Determine the shear modulus G, the proportional limit, and the ultimate shear stress. Also, determine the maximum distance d that the top of a block of this material, shown in Fig. b, could be displaced horizontally if the material behaves elastically when acted upon by a shear force V. What is the magnitude of V necessary to cause this displacement?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
An Introduction to Stress and Strain; Author: The Efficient Engineer;https://www.youtube.com/watch?v=aQf6Q8t1FQE;License: Standard YouTube License, CC-BY