Applied Statics and Strength of Materials (6th Edition)
6th Edition
ISBN: 9780133840544
Author: George F. Limbrunner, Craig D'Allaird, Leonard Spiegel
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 10, Problem 10.17SP
Compute the modulus of elasticity of a copper alloy wire that stretches 14.0 mm when subjected to a load of 320 N. The wire is 4.00 m long and has a diameter of 1.00 mm.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Calculate the Young Modulus for a mild steel. When a rod of the steel is being tested under
tensile load. The rod is 4.5m long with a diameter of diameter of 35mm and suffers an
extension of 0.9mm under a load of 50,000N
259 x 106 N/m²
259GN/m²
55MN/m²
64GN/m²
A tube has 25mm outside diameter and an axial tensile load of 40 kN. If the strain on the tube is limited to 0.1% and density of 7800kg/m^3, what is the maximum internal diameter of the tube in mm?
A copper alloy wire of 1.5 mm diameter and 30 m long is hanging freely from a tower. What will be its elongation due to self weight? Take specific weight of the copper and its modulus of elasticity as 89.2 kN/m' and 90 GPa respectively
Chapter 10 Solutions
Applied Statics and Strength of Materials (6th Edition)
Ch. 10 - A 916 - in. - diameter steel rod is tested in...Ch. 10 - A concrete cylinder 150 mm in diameter was tested...Ch. 10 - Prob. 10.3PCh. 10 - The data from the tension test of a steel specimen...Ch. 10 - An 18-in.-long titanium alloy rod is subjected to...Ch. 10 - ASTM A36 steel rods are used to support a balcony....Ch. 10 - A 450-mm-long AISI 1020 steel rod is subjected to...Ch. 10 - A tension member in a roof truss is composed of...Ch. 10 - A short, solid, compression member of circular...Ch. 10 - A main cable in a large bridge is designed for a...
Ch. 10 - Test results of a steel specimen indicated an...Ch. 10 - A concrete canoe in storage is supported by two...Ch. 10 - A load is applied to a rigid bar that is...Ch. 10 - Prob. 10.14CPCh. 10 - Write a program that will allow a user to input...Ch. 10 - A 12 - in. - diaiíct.cr structural nickel steel...Ch. 10 - Compute the modulus of elasticity of a copper...Ch. 10 - A concrete cylinder 6 in. in diameter was tested...Ch. 10 - An aluminum bar 2 in. by 12 - in. in cross section...Ch. 10 - During a tensile test of a steel specimen, the...Ch. 10 - A 12.5-mm-diameter steel rod was subjected to a...Ch. 10 - Prob. 10.22SPCh. 10 - A standard steel specimen having a diameter of...Ch. 10 - 10.24 A tension member in a structure is composed...Ch. 10 - A pair of wire cutters is designed to operate...Ch. 10 - Calculate the end bearing length required for a...Ch. 10 - Design a 3-m-long rod subjected to a tensile load...Ch. 10 - The collar bearing shown is subjected to a...Ch. 10 - A 10-ft-long steel member is subjected to a...Ch. 10 - Two steel bars A and B support a load P, as shown....Ch. 10 - Prob. 10.31SP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A metal bar 5.0 m long extends by 0.05 mm when a tensile load is applied to it. The percentage strain is:arrow_forwardThe is a rope that just cannot stretch more than 0.6 cm from a tensile force of 500N without breaking. What is the minimum radius that the rope must have if it is .5kg and .6 meters long? The Young’s modulus for this material is 35*10^9 Pa.arrow_forward2. A load of 500 N is applied on a cylindrical wire of 3.0 mm diameter and 2.5 x 10 mm length. The wire is made of titanium with modulus of elasticity of 107 GPa. Assume that the deformation is within the elastic region, calculate the elongation of the wire.arrow_forward
- Determine the width and thickness of the leaves (in mm) of a leaf spring using the following specifications: Total load = 140 kN; Number of springs supporting the load = 4; Maximum number of leaves = 10; Span of the spring = 1000 mm; Permissible deflection = 80 mm; Modulus of elasticity, E = 200 kN/mm2; and allowable stress in spring material is 600 MPa.arrow_forwardA cylindrical structural element is made of steel. The element must withstand an axial load of 160 kN. Determine the diameter of its cross section so that it does not have plastic deformation. What is the load that this element resists if it is 80 cm long and suffers an elongation of 200 micrometers? Consider an elastic modulus of 200 G Pa. And a yield stress of 340 M Pa. Use a factor of safety of 3/5 with respect to the yield stress.arrow_forwardA 5 meter-long steel bar that is 2.5 cm in diameter is stretched 2.0 mm by an axial load of 80kN in pulling it axially. Calculate the modulus of elasticity of the bar.arrow_forward
- 21. Calculate the Youngs modulus for the material of the bar shown below. The bar has an initial length of 400 mm to tneasured to extend by 0.22 mm under a tensile load of 75KN. When the force is released the bar returns to its original length. The bar has the rectangular cross-section shown below. (17p) 20 mm 75 KN- 75KN 25 mm 400 mmarrow_forwardExperiments were conducted in a tension testing machine to evaluate the material properties of two metallic rods both having diameter equal to 10 mm. First rod having modulus of rigidity of the material equal to 400 tonnes/cm2 when subjected to an axial tensile force of 6 kN, the change in its diameter was observed to be 0.0018 cm. The value for the bulk modulus of the second metallic rod is same as that of the first one but modulus of elasticity 18% more. Based on the material properties calculate and compare the values of different moduli as well as Poisson’s ratio for both metallic rods. Justify your answer with reasons.arrow_forwardA bar is 500 mm long and is stretched to 505 mm with a force of 50 kN. The bar is 10 mm diameter. Determine stress, strain and elastic modulus.arrow_forward
- A mild steel tube of external diameter 80mm and internal diameter 60mm is enclosed centrally inside the brass tube of same length and having external diameter 100mm and internal diameter 80mm. The ends of the tubes are brazed together and the composite arrangement is subjected to axial pull of 25kN. If the modulus of elasticity for steel and brass are 200 GPa and 100 GPa respectively and tube length is 30cm. Make calculation for the load carried. Shortening in length of each tube.arrow_forwardA metal specimen 43 mm in diameter has a length of 304 mm. A force of 613 kN elongates the length by 2.24 mm. What is the modulus of elasticity?arrow_forward1. Consider a cylindrical specimen of some hypothetical metal alloy that has a diameter of 12.0 mm. A tensile force of 1500 N produces an elastic reduction in diameter of 6.8 x 10 mm. Compute the elastic modulus of this alloy, given that Poisson's ratio is 0.35.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license