Derive two dimensionless parameters for the shear stress at the pipe wall when an incompressible fluid flows through a pipe under pressure. In the dimensional analysis, use the following significant parameters: pipe diameter, flow velocity, viscosity of the fluid and density of the fluid. Solve the problem on white A4 size paper. Show all the calculation steps.

Derive two dimensionless parameters for the shear stress at the pipe wall when an incompressible fluid flows through a pipe under pressure. In the dimensional analysis, use the following significant parameters: pipe diameter, flow velocity, viscosity of the fluid and density of the fluid. Solve the problem on white A4 size paper. Show all the calculation steps.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.13P: 5.13 The torque due to the frictional resistance of the oil film between a rotating shaft and its...

See similar textbooks

Similar questions

5.13 The torque due to the frictional resistance of the oil film between a rotating shaft and its bearing is found to be dependent on the force F normal to the shaft, the speed of rotation N of the shaft, the dynamic viscosity of the oil, and the shaft diameter D. Establish a correlation among these variables by using dimensional analysis.
An airplane wing model is designed with a similarity test. the sustaining force is a function of speed, chord, density, viscosity, speed of sound and angle of attack. determine the dimensionless numbers
Please solve the sub parts A,B,C with the step.. The all part same the chapter thank u A. Investigate with dimensional analysis, is this equation true t = [ 2x / a ]1/2 B. Express 0.00034 m in microns C. Express 8.31 x 1014 seconds in pico seconds
The differential equation for small-amplitude vibrations y(r, f) of a simple beam is given by a*y + E = 0 ax pA where p = beam material density A = cross-sectional area I= area moment of inertia E = Young's modulus Use only the quantities p, E, and A to nondimensionalize y, x, and t, and rewrite the differential equation in dimensionless form. Do any parameters remain? Could they be removed by further manipulation of the variables?
The power P required for operating a pump depends on the diameter of the pump D, the pressure rise Ap across the pump, the fluid density p, the fluid viscosity and the Theorem, and D, Q and p as the repeating variables, the dimensionless group associated with μ is given by volume flow rate Q through the pump. Using Buckingham's μDªQbpº. Determine the values of a, b and c. 1. [0.99, 1.01 2. [-1.01, 0.99 3. [-1.01, -0.99 a= b = C=
Three students at NUST derive the following equations in which x refers to distance traveled, v the speed, a the acceleration (m/s2), and t the time, and the subscript (0) means a quantity at time t=0: (i) x=vt2+2at, (ii) x= v0t +at2 (iii) x=v0t +2at2 Which of these could be possibly be correct according to a dimensional check?
A simply supported beam of diameter D, length L, and modulus of elasticity E is subjected to a fluid crossflow of velocity V, density p, and viscosity u. Its center deflection & is assumed to be a function of all these variables. Part A-Rewrite this proposed function in dimensionless form.
Solve for the specific volume and specific weight in SI units and Dynamic Viscosity in Poise. The specific gravity of alcohol is 0.52 and its kinematics viscosity is equal to (your registration number/2 e.g., 4193/2) Centi Stokes.
The Reynolds transport theorem (RTT) is discussed in Chap. 4 of your textbook. For the general case of a moving and/or deforming control volume, we write the RTT as follows: d pb dV + pbV-ñ dA dt dt dB sys where Vr is the relative velocity, i.e., the velocity of the fluid relative to the control surface. Write the primary dimensions of each additive term in the equation and verify that the equation is dimensionally homogeneous. Show all your work. (Hint: Since B can be any property of the flow-scalar, vector, or even tensor—it can have a variety of dimensions. So, just let the dimensions of B be those of B itself, {B}. Also, b is defined as B per unit mass.)
Which of the following dimensionless parameters is the correct arrangement of the given parameters? (select all that O a. Pi = (Dp)/(Rho*V) Dp: Pressure change Rho: Density V: Velocity O b. Pi = (V*L*(Rho))/(nu) V: Velocity L: length Rho: Density nu: Dynamic viscosity O. Pi = Q/((A^1.5)*w) Q: Volumetric discharge rate A: Area w: Angular velocity O d. Pi = (a)(t^2)/(L) L: length a: acceleration t time
Please solve this problem, Thank you very much! Figure is attached 1. liquids in rotating cylinders rotates as a rigid body and considered at rest. The elevation difference h between the center of the liquid surface and the rim of the liquid surface is a function of angular velocity ?, fluid density ?, gravitational acceleration ?, and radius ?. Use the method of repeating variables to find a dimensionless relationship between the parameters. Show all the steps.
A2) In order to solve the dimensional analysis problem involving shallow water waves as in Figure 2, Buckingham Pi Theorem has been used. h Figure 2 Through the observation that has been done, the wave speed © of waves on the surface of a liquid is a function of the depth (h), gravitational acceleration (g), fluid density (p), and fluid viscosity (µ). By using this Buckingham Pi Theorem: a) Analyze the above problem and show that the Froude Number (Fr) and Reynolds Number (Re) are the relevant dimensionless parameters involve in this problem. b) Manipulate your Pi (1) products to get the parameter into the following form: pch := f(Re) where Re = Fr = c) If one additional primary variable parameter involve in this proolem such as, temperature (T). Discuss on the Pi (m) products that can be produce and explain why this dimensional analysis is very important in the experimental work.