A household refrigerator with a COP of 1.25 removes heat from the refrigerated space at a rate of 90kJ/min Determine (a) the electric power consumed by the refrigerator and (b) the rate of heat transfer to the kitchen air.

A household refrigerator with a COP of 1.25 removes heat from the refrigerated space at a rate of 90kJ/min Determine (a) the electric power consumed by the refrigerator and (b) the rate of heat transfer to the kitchen air.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.46P

See similar textbooks

Related questions

Q: 1.5 m 1.0 m A B 3.3 m FIGURE P1.10 C 15 kN 12 kN

A: Considering that you want to know the forces in the members.Thus the reaction forces are as shown…

Q: The guide with the vertical slot is given a horizontal oscillatory motion according to x = 5.1 sin…

A: Given:To find:Position, time and max velocity

Q: 04: 3 kg of air at 1.5 bar pressure and 77°C temperature at sta polytropically to state 2 at…

Q: Determine the maximum speed for each car if the normal acceleration is limited to 0.81g. The roadway…

A: given

Q: Question 7 find the wter pressure at pipe in this system? (Use HAZEN- WILLIAM CH-130, 0-1.2 m³/s…

A: The water reservoir elevation, H1 = 103.5 mThe tap elevation, H2 = 55 mThe diameter of pipe, d = 100…

Q: 36MPa 88 MPa 36 MPa

A: The given state of plane stress is -Find: Principal stresses and Principal directions

Q: 1 kg of a gas at a temperature of 40° C and a pressure of 120 KPa occupies a volume of 0.25m3. If…

Q: On its takeoff roll, the airplane starts from rest and accelerates according to a = ao - kv² where…

Q: During the compression cycle of a diesel engine, the 0.5 L piston compresses, 100,200 Pa air at…

Q: Q1: Show with mechanism, What are happened to the following polymers: 1- Polypropylene exposed to…

A: This question is based on the concept of polymers. As per the guidelines we are subjected to solve…

Q: Determine the reactions at pin support A and roller support B when ß = 50°.

Q: t₁ = t2 = i i sec, |v|= Mi sec, |v|= i ft/sec ft/sec

Q: is compressed 2 04: 3 kg of air at 1.5 bar pressure and 77°C temperature at state polytropically to…

Q: compute the maximum deflection of the beam Wu = 2.12 kip lft P₁ = 18.4 kips TR 10 ft = 27.008k…

A: The intensity of UDL, Wu = 2.12 kip/ftThe point load, Pu = 18.4 kips

Q: A horseshoe player releases the horseshoe at A with an initial speed vo= 36 ft/sec. Determine the…

A: According to the given datav=36ft/sSA=2.9ft andSB=11in=0.917ftSAB=-2.9+0.917=-1.983 ftWe need to…

Q: The equivalent stress for welding in given bracket connections would be if t te = 5mm i.e. Effective…

A: Effective throat thickness of weld te = 5mmP = 50 × 10³ KNe = 200 mmh = 250 mm

Q: Using the method of joints, determine the force in each member of the truss shown

Q: two 20 x 100-mm and two 20 x 180 mm boards are glued together as shown to form a 120 x 200 mm box…

A: According to the given dataV=3.635kNWe need to findShear stress at glued point-B

Q: What are the key steps involved in the design process of a mechanical engineering project, and how…

A: The Design Process in Mechanical EngineeringThe design process is a systematic approach to creating…

Q: B): Specify the pressure class for a 16-inch (0.375in wall thickness) liquid seamless-pipeline…

Q: Below is the arrangement for a gear train. A motor delivers 200-hp at 540-RPM to the input gear A.…

A: The motor horse power, P = 200 hpThe speed of gear A, NA = q = 540 rpm

Q: Required information The structure consists of pin-connected members. Take X= 4 kN. NOTE: This is a…

A: Given

Q: A metal composite wall consists of two outer metal skins (k = 100 W/m.k) 2 mm thick which sandwich…

A: Given - For a composite wall thermal…

Q: The water nozzle ejects water at a speed vo = 37.7 ft/sec at the angle 0 = 41°. Determine the…

A: Given:Initial velocity = To find:Distance h above the base point B where the water lands.

Q: Question 2 Figure 2 shows the cross-sectional of inner and outer surfaces of a 4 m x 7 m brick wall…

A: The cross-section of the wall, A = 4 m*7 mThe thickness of the wall, L = 30 cm = 0.3 mThe thermal…

Q: EFx=0= (0.433 F1) - (0.667 F2) - (0.866 F3) + (0.342 P) EFy=0= - (0.250 F1) + (0.667 F2) EFz=0=…

A: Final equation obtained from the solution are provided.In the similar problems value P is generally…

Q: Determine the minimum distance d between the cars so as to avoid a collision.

Q: The beam shown supports a load that varies uniformly from 100 N/m at the left end to 200 N/m at the…

A: Note-According to policy only first three questions can be answered so resubmit for complete…

Q: A force of P = 20 N is applied to the cable, which causes a 175 kg of radius of Gyration KG = 0.42m…

A: To calculate the work done by the force of 20 N for 2 revolutions, we need to find the distance…

Q: m 50 cm. 2008 (2) 30 CL 'X Calculate the coordinates of the center of gravity of the homogeneous…

Q: A model rocket is launched from rest with a constant upward acceleration of 2.5 m/s² under the…

Q: A rigid vessel containing water has a temperature of 200 C and a pressure 200 kPa with a volume of…

Q: For an ideal Rankine cycle, steam first enters the turbine at 5 MPa and 500C then it expands to a…

A: The quality of steam, the heat addition, the heat rejected, the turbine work, the pump work, the…

Q: Consider the element below: 30MPa Version 1 y 50MPa > X 40MPa From the statements below, choose the…

Q: What are the fundamental principles of engineering metrology and how do they contribute to ensuring…

A: Engineering metrology is the study of measurement science and the application of that science to…

Q: A centrifugal pump pumps water at a flow rate of 7 m³/s to a height of 10 m. If the pump works at…

A: Flow rate (Q) = 7 m³/s, Height (H) = 10 m, CQ=0.15 CH=6 CP=0.75.To find:Pump impeller diameter…

Q: This question is made of two separate parts related to figures 1 and 2. 2 m F a Figure 1 2m The…

A: Note :- as per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: The towline exerts a force of P = 4 kN at the end of the 20-m-long crane boom. If x = 32 m,…

Q: A spring is made of 2.0 mm diameter music wire A228 (set not removed). Determine its maximum…

A: music wire A228 (set not removed).Diameter of music wire = 2 mm

Q: What are the factors that influence the buckling behavior of an axially loaded slender column in…

A: Buckling is a sudden, unstable deformation of a structure, often leading to its failure. It…

Q: Calculate -3 -6 . 10 ft L -3 ft a dx. a, ft/sec² 19 0 0 x, ft 5 7 10

A: Consider following acceleration vs displacement graph.We need to determine the total acceleration…

Q: Problem 2 A counterflow heat exchanger with both fluids (i.e., water and air) being unmixed. The…

A: The water flow rate, mw = 0.07 kg/sThe temperature of water at entry, Tw1 = 400 KThe temperature of…

Q: 1 kg of a gas at a temperature of 40° C and a pressure of 120 Ka occupies a volume of 0.25m^3. If…

Q: Calculate the minimum possible magnitude u of the muzzle velocity which a projectile must have when…

Q: 2. The disk is originally rotating at w=8 rad/s. If it is subjected to a constant angular…

A: Initial angular speed of disk is 8 rad/s Angular acceleration is 6 rad/s^2 Required: Velocity,…

Q: 1. A thin pole of length L = 3 m and mass 6 kg is being raised by a rope of tension 80 Newtons as…

Q: A uniform supersonic airstream travelling at a Mach number of 9.0 passes over a concave corner, as…

A: Mach number,M1=9.0shock angle,Assume,Deviation angle be

Q: The force of F = 55 lb acts along the edge DB of the tetrahedron shown in (Figure 1). Figure 8 ft 10…

A: GIVEN- FORCE ACTS ALONG THE EDGE DB IS F=55lbDETERMINE- magnitude the amount of force…

Q: Determine the magnitude of force at the pin A and in the cable BC needed to support the 500-lb load.…

Q: W B A Y Fj FM

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Calculations

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A condenser of a refrigeration system rejects heat at a rate of 120 kW while compressor consumes power of 30 kW. the coefficient of performance of the system would be.
A heat pump with a COP of 3.2 is used to heat a perfectly sealed house (no air leaks). The entire mass within the house (air, furniture, etc.) is equivalent to 1200 kg of air. When running, the heat pump consumes electric power at a rate of 5 kW. The temperature of the house was 7°C when the heat pump was turned on. If heat transfer through the envelope of the house (walls, roof, etc.) is negligible, the length of time the heat pump must run to raise the temperature of the entire contents of the house to 22°C is (a) 13.5 min (b) 43.1 min (c) 138 min (d) 18.8 min (e) 808 min
3. An air conditioner removes heat steadily from a house at a rate of 750 klimin while drawing electric power at a rate of 6 kW. Determine (a) the COP of this air conditioner and (b) the rate of heat transfer to the outside air. (20R. 0 min 1
The food compartment of a refrigerator is maintained at 4°C by removing heat from it at a rate of 347 kJ/min. If the required power input to the refrigerator is 3 kW, determine the rate of heat rejection to the room that houses the refrigerator. Select one: a. 480 kJ/min b. 610 kJ/min c. 394 kJ/min d. 527 kJ/min
By supplying energy to a house at a rate of 25,000 kJ/hr, a heat pump maintains the temperature of the dwelling at 20 C when the outside air is at -10 C. If electricity costs 8 cents per kW-hr, determine the minimum theoretical operating cost to heat the house for 24 hours. $1.97 O $1.37 $1.75 O $1.51 O$1.64
A domestic refrigerator with a COP of 1.2 removes heat from the refrigerated space at a rate of 60 kJ/min. Determine a) the electrical power consumed by the refrigerator and b) the rate of heat transfer to the kitchen air.
4. A household refrigerator with a COP of 1.25 removes heat from the refrigerated space at a rate of OL Determine (a) the electric power consumed by the refrigerator and (b) the rate of heat transfer to the kitchen air. (20 Do Student number 1 210505269 2 200505527 QL (kJ/min) 90 89 Student 16/10 17
A heat engine with a thermal efficiency of 45 percent rejects 1500 kJ / kg of heat. How much heat does it receive?
A heat engine receives a heat-transfer at the rate of 2 MW at a high temperature of 750 °C. The engine releases energy to its surrounding at 300 K and work is produced at a rate of 1200 kW. What are 1. The energy released to the ambient surroundings? 2. The efficiency of the engine?
The thermal efficiency of an engine used to drive a refrigerator is 30%. The heat input into the engine for each MJ removed from the cold body by the refrigerator is 666.67 kJ. What is the COP of the refrigerator?
A heat pump is used to maintain a space at 25 C during winter while the outdoor temperature is 10 C. The total rate of heat 1) loss from the space to the outside is 20 kW. The power (in W) needed to drive this heat pump (assuming it is reversible) is Select one: 806 1016 906 1006
In a given process, a heat engine requires 2500J of energy and exhausts 1200J of heat. What is its efficiency?