Applied Statics and Strength of Materials (6th Edition)
6th Edition
ISBN: 9780133840544
Author: George F. Limbrunner, Craig D'Allaird, Leonard Spiegel
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 9, Problem 9.16P
A 100-ft-long rod is suspended from one end. The diameter of the rod is 1 in. and the total elongation is 0.80 in. Calculate the maximum strain.
Expert Solution & Answer
Learn your wayIncludes step-by-step video
schedule03:29
Students have asked these similar questions
A 200 meter cable is suspended vertically. At any point along the cable, the strain is proportional to the length of the cable below the point. If the strain at the top of the cable is 0.001, determine the total elongation of the cable.
2.Show that volumetric strain in a bar is equal to the sum of strains in three mutually perpendicular directions.
3. Explain the terms:
(i) Modulus of elasticity (ii) Modulus of rigidity and
(ii) Bulk modulus.
4. Derive the relationship between
(i) Modulus of elasticity and modulus of rigidity (ii) Modulus of elasticity and bulk modulus
A specimen of copper having a rectangular cross section of 15.2 x 19.1 mm is pulled with a force of 44.5 kN, producing only elastic deformation. Calculate the strain. E is 110 Gpa.
Chapter 9 Solutions
Applied Statics and Strength of Materials (6th Edition)
Ch. 9 - Write the direct stress formula in its three forms...Ch. 9 - A 6-in-diameter concrete test cylinder is loaded...Ch. 9 - Determine the tensile stress in each segment of...Ch. 9 - Calculate the stress developed in the following...Ch. 9 - The following members are subjected to axial...Ch. 9 - Determine the stresses in the two segments of the...Ch. 9 - A bin weighing 8 tons is supported by three steel...Ch. 9 - Diameters of small commercially available steel...Ch. 9 - A No. 32 (metric designation) reinforcing bar for...Ch. 9 - In the bolted connection of Figure 9.12 , assume...
Ch. 9 - Compute the force required to punch a...Ch. 9 - The 34 — in. — diameter bolt shown is subjected to...Ch. 9 - Why is strain unitless (or dimensionless)?Ch. 9 - (a) Given =1.2in. and L=100ft calculate (b) Given...Ch. 9 - A short compression member 2 in. by 2 in. in cross...Ch. 9 - A 100-ft-long rod is suspended from one end. The...Ch. 9 - Compute the total elongation of a steel bar,...Ch. 9 - A steel rod 34 in. in diameter and 25 ft long is...Ch. 9 - An aluminum rod 25mm in diameter and 4m long is...Ch. 9 - A steel rod 10 ft long is made up of two 5 ft...Ch. 9 - A titanium alloy bar elongates 0.500 in. when...Ch. 9 - Write a program that will calculate the allowable...Ch. 9 - Write a program that will compute stress, strain,...Ch. 9 - The Viking Bin Company manufactures suspended bins...Ch. 9 - Write a computer program that will calculate the...Ch. 9 - The joint between a diagonal and a chord in a...Ch. 9 - In Problem 9.26, find the required length of the...Ch. 9 - A column is supported by a base plate, pedestal,...Ch. 9 - If the soil pressure under the footing of Problem...Ch. 9 - A hopper weighing 75 kN is supported by three...Ch. 9 - A steel bar has a rectangular cross section 25 mm...Ch. 9 - A steel wire is suspended vertically from its...Ch. 9 - A W1240 shape is subjected to a tensile load of...Ch. 9 - Calculate the required diameter of steel tie rods...Ch. 9 - A 30-ft-long steel rod of circular cross section...Ch. 9 - Consider the bolted lap joint shown in Figure...Ch. 9 - An inclined member is braced with a glued block,...Ch. 9 - Calculate the force a punch press must exert if it...Ch. 9 - A 34 - in. - diameter punch is used to punch a...Ch. 9 - A control arm is keyed to a 1-in. -diameter shaft...Ch. 9 - Calculate the required width b for the key of...Ch. 9 - A 25-mm-diameter aluminum rod, 3 m long, is...Ch. 9 - A short timber post of Douglas fir is subjected to...Ch. 9 - A 1 00-ft surveyor’s steel tape with a...Ch. 9 - An 18-in-long steel rod is subjected to a tensile...Ch. 9 - Compute the magnitude of the tensile load that...Ch. 9 - A 5-mm-diameter steel wire, 18 m in length, is...Ch. 9 - A structural steel rod 112 in. in diameter and 20...Ch. 9 - A rectangular structural steel eyebar 34 in. thick...Ch. 9 - 9.50 A
in. — diameter steel rod, 100 ft long, is...Ch. 9 - For the truss shown, compute the total deformation...Ch. 9 - A steel bar with a cross section of 12 in. by 12...Ch. 9 - Rework Problem 9.52 , changing the second load...Ch. 9 - In the structure shown, the tie-back BC is a round...Ch. 9 - A hook is suspended by two steel wires, as shown....Ch. 9 - The trolley of a small hoist is supported on a...Ch. 9 - The steel piston rod to the master cylinder has a...Ch. 9 - A stranded steel brake cable is composed of 7...Ch. 9 - The piston of a steam engine is 400 mm in diameter...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Determine the resultant forces at pins B and C on member ABC of the four-member frame. Prob. R6-8
Engineering Mechanics: Statics
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
In each case, construct the parallelogram law to show FR = F1 + F2. Then establish the triangle rule, where FR ...
Statics and Mechanics of Materials (5th Edition)
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
The free body diagram of the ring at A. The magnitude of force in each cable.
Engineering Mechanics: Statics & Dynamics (14th Edition)
ICA 2-1
For each of the following situations, indicate whether you think the action is ethical or unethical or ...
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Acetal plastic has a stress-strain diagram as shown. If a bar of this material has a length of 3 ft and cross-sectional area of 0.875 in2, and is subjected to an axial load of 2.5 kip, determine its elongation.arrow_forwardA steel bar is stressed to 280MPa.The modulus of elasticity is 205 GPa. The bar is 80mm diameter and 240 mm long. Determine the following I) the strain 2) the forcearrow_forwardIf the engineering strain in a tensile bar is 0.0025 and Poisson’s ratio is 0.33, find the original length and the original diameter if the length and diameter under load are 2.333 ft. and 1.005 in. respectively.arrow_forward
- Calculate the strain in a metal with a Young’s modulus of 210 GPa and subjected to 440 MPa.arrow_forwardA Mild steel rod of 15mm diameter that is 1.5 cm in length is elongated by 0.15mm along its longitudinal direction by a load of 15 kN. Hence, the strain of the material is …………….. mm/mm.arrow_forwardIf the Young's modulus and Poisson's ratio of the container material are 100 GPa and 0.3 respectively, What is the axial strain in the cylinder wall at mid-depth?arrow_forward
- A tensile bar is stressed to 250 N/mm2 which is beyond its elastic limit. At this stage the strain produced in the bar is observed to be 0.0014. if the modulus of elasticity of the material of the bar is 205000 N/mm2 then the elastic component of the strain is very close toa. 0.0004b. 0.0002c. 0.0001d. 0.00005 PLS EXPLAIN YOUR ANSWER THOROUGHLYarrow_forwardA steel bar of 3 m long and 2500 mm2 in area hangs vertically, which is securely fixed on a collar at its lower end . If a weight of 25 KN falls on the collar from the height of 10 mm , determine the stress induced in the bar. What will be the strain energy stored in the bar? Take E=200 GPa.arrow_forwardCompare the strain energies of two bars of the same material and length and carrying the same gradually applied compressive load if one is 25 mm diameter throughout and the other is turned down to 20 mm diameter over half its length, the remainder being 25 mm diameter. If both bars are subjected to pure torsion only, compare the tensional strain energies stored if the shear stress in both bars is limited to 75 MN/m2arrow_forward
- A tensile force of 10 kN is applied on a 0.02-m diameter and 2-m long rod. After applying theload, the diameter of the rod decreases to 0.01998 m and the length increases to 2.01 m. The lateral (transverse) strain is?arrow_forwardWhen force P is apliced to the rigid arm BC, point B moves downward 0.2mm. Determine the normal strain developed in wire CD: ___ mm/mm. Calculate your answer to 4 digit place.arrow_forwardCan the normal strain on the free surface of a body be measured in aparticular direction using an electrical resistance strain gage? Give an example?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Strain energy and strain energy density introduced; Author: Engineer4Free;https://www.youtube.com/watch?v=m14sqLGg4BQ;License: Standard youtube license