Fluid Mechanics
8th Edition
ISBN: 9780073398273
Author: Frank M. White
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 8, Problem 8.39P
A large Rankine oval, with a = 1 m and h = 1 m, is immersed in 20°C water flowing at 10 m/s. The upstream pressure on the oval centerline is 200 kPa. Calculate (a) the value of m; and (b) the pressure on the top of the oval (analogous to point A in Fig. P8.37).
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Water at 20°C flows through the orifice in Fig. ,which is monitored by a mercury manometer. If d = 3 cm,(a) what is h when the flow rate is 20 m3/h and (b) what isQ in m3/h when h = 58 cm?
A water jet 3 in in diameter strikes a concrete (SG =2.3)slab which rests freely on a level fl oor. If the slab is 1 ft wide into the paper, calculate the jet velocity which willjust begin to tip the slab over.
A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev. 15m). The head loss from the reservoir (point 1) to the summit (point 2, elev. 22m) is 2.5 times the velocity head in the siphon and head loss from the summit to the discharge end is 4 times the velocity head in the siphon. What is the absolutepressure at the summit (point 2) assuming the atmospheric pressure to be 101.3 kPa?
Do not write the unit. You will only input the numerical answer in the space provided.
Unit of the Correct Answer: kPa (indicate the sign if negative)
Decimal Places required in the final answer: 3
Chapter 8 Solutions
Fluid Mechanics
Ch. 8 - Prob. 8.1PCh. 8 - The steady plane flow in Fig. P8.2 has the polar...Ch. 8 - P8.3 Using cartesian coordinates, show that each...Ch. 8 - P8.4 Is the function 1/r a legitimate velocity...Ch. 8 - Prob. 8.5PCh. 8 - An incompressible plane flow has the velocity...Ch. 8 - Prob. 8.7PCh. 8 - For the velocity distribution u=By,=+Bx , evaluate...Ch. 8 - Prob. 8.9PCh. 8 - Prob. 8.10P
Ch. 8 - Prob. 8.11PCh. 8 - Prob. 8.12PCh. 8 - P8.13 Starting at the stagnation point in Fig....Ch. 8 - P8.14 A tornado may be modeled as the circulating...Ch. 8 - Hurricane Sandy, which hit the New Jersey coast on...Ch. 8 - Prob. 8.16PCh. 8 - P8.17 Find the position (x, y) on the upper...Ch. 8 - Prob. 8.18PCh. 8 - Prob. 8.19PCh. 8 - Plot the streamlines of the flow due to a line...Ch. 8 - P8.21 At point A in Fig. P8.21 is a clockwise line...Ch. 8 - P8.22 Consider inviscid stagnation flow, (see...Ch. 8 - P8.23 Sources of strength m = 10 m2/s are placed...Ch. 8 - P8.24 Line sources of equal strength m = Ua, where...Ch. 8 - Prob. 8.25PCh. 8 - Prob. 8.26PCh. 8 - Prob. 8.27PCh. 8 - Sources of equal strength m are placed at the four...Ch. 8 - Prob. 8.29PCh. 8 - Prob. 8.30PCh. 8 - A Rankine half-body is formed as shown in Fig....Ch. 8 - Prob. 8.32PCh. 8 - P8.33 Sketch the streamlines, especially the body...Ch. 8 - Prob. 8.34PCh. 8 - Prob. 8.35PCh. 8 - Prob. 8.36PCh. 8 - Prob. 8.37PCh. 8 - Consider potential flow of a uniform stream in the...Ch. 8 - A large Rankine oval, with a = 1 m and h = 1 m, is...Ch. 8 - Prob. 8.40PCh. 8 - Prob. 8.41PCh. 8 - Prob. 8.42PCh. 8 - P8.43 Water at 20°C flows past a 1-rn-diameter...Ch. 8 - Prob. 8.44PCh. 8 - Prob. 8.45PCh. 8 - P8.46 A cylinder is formed by bolting two...Ch. 8 - Prob. 8.47PCh. 8 - Prob. 8.48PCh. 8 - Prob. 8.49PCh. 8 - It is desired to simulate flow past a...Ch. 8 - Prob. 8.51PCh. 8 -
P8.52 The Flettner rotor sailboat in Fig. E8.3...Ch. 8 - P8.52 The Flettner rotor sailboat in Fig. E8.3 has...Ch. 8 - Prob. 8.54PCh. 8 - Prob. 8.55PCh. 8 - Prob. 8.56PCh. 8 - Prob. 8.57PCh. 8 - Prob. 8.58PCh. 8 - Prob. 8.59PCh. 8 - Prob. 8.60PCh. 8 - Prob. 8.61PCh. 8 - Prob. 8.62PCh. 8 - The superposition in Prob. P8.62 leads to...Ch. 8 - Consider the polar-coordinate stream function...Ch. 8 - Prob. 8.65PCh. 8 - Prob. 8.66PCh. 8 - Prob. 8.67PCh. 8 - Prob. 8.68PCh. 8 - Prob. 8.69PCh. 8 - Prob. 8.70PCh. 8 - Prob. 8.71PCh. 8 - Prob. 8.72PCh. 8 - Prob. 8.73PCh. 8 - Prob. 8.74PCh. 8 - Prob. 8.75PCh. 8 - Prob. 8.76PCh. 8 - Prob. 8.77PCh. 8 - Prob. 8.78PCh. 8 - Prob. 8.79PCh. 8 - Prob. 8.80PCh. 8 - Prob. 8.81PCh. 8 - Prob. 8.82PCh. 8 - Prob. 8.83PCh. 8 - Prob. 8.84PCh. 8 - Prob. 8.85PCh. 8 - Prob. 8.86PCh. 8 - Prob. 8.87PCh. 8 - Prob. 8.88PCh. 8 - Prob. 8.89PCh. 8 - NASA is developing a swing-wing airplane called...Ch. 8 - Prob. 8.91PCh. 8 - Prob. 8.92PCh. 8 - Prob. 8.93PCh. 8 - Prob. 8.94PCh. 8 - Prob. 8.95PCh. 8 - Prob. 8.96PCh. 8 - Prob. 8.97PCh. 8 - Prob. 8.98PCh. 8 - Prob. 8.99PCh. 8 - Prob. 8.100PCh. 8 - Prob. 8.101PCh. 8 - Prob. 8.102PCh. 8 - Prob. 8.103PCh. 8 - Prob. 8.104PCh. 8 - Prob. 8.105PCh. 8 - Prob. 8.106PCh. 8 - Prob. 8.107PCh. 8 - P8.108 Consider two-dimensional potential flow...Ch. 8 - Prob. 8.109PCh. 8 - Prob. 8.110PCh. 8 - Prob. 8.111PCh. 8 - Prob. 8.112PCh. 8 - Prob. 8.113PCh. 8 - Prob. 8.114PCh. 8 - Prob. 8.115PCh. 8 - Prob. 8.1WPCh. 8 - Prob. 8.2WPCh. 8 - Prob. 8.3WPCh. 8 - Prob. 8.4WPCh. 8 - Prob. 8.5WPCh. 8 - Prob. 8.6WPCh. 8 - Prob. 8.7WPCh. 8 - Prob. 8.1CPCh. 8 - Prob. 8.2CPCh. 8 - Prob. 8.3CPCh. 8 - Prob. 8.4CPCh. 8 - Prob. 8.5CPCh. 8 - Prob. 8.6CPCh. 8 - Prob. 8.7CPCh. 8 - Prob. 8.1DPCh. 8 - Prob. 8.2DPCh. 8 - Prob. 8.3DP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Using the figure depicted below, perform the following: (a) Calculate the minimum height h at which cavitation occurs. Indicate on the figure where the cavitation occurs. (b) Calculate the volume flowrate (in m³/s) if h = 25 cm. Be sure to state all assumptions. Note that section 2 opens to atmosphere. D1 = 5 cm h D2 = 10 cm Free Jet (1) 2 Water at 20°Carrow_forwardTwo water tanks, each with base area of 1 ft2, are connectedby a 0.5-in-diameter long-radius nozzle as in Fig. .If h = 1 ft as shown for t = 0, estimate the time for h(t) todrop to 0.25 ft.arrow_forward(1) shown in the figure below is only 2 mm in diameter. Take water density p dynamic viscosity u = 0.001 kg/(m.s) In Tinyland, houses are less than a foot high! The rainfall is laminar! The drainpipe = 998 kg/m and (a) When the gutter is full, simplify the steady flow energy equation by neglecting the gutter velocity and using the head loss due to a laminar flow, determine the draining velocity V and draining flow rate Q. (b) The gutter is designed for a sudden rainstorm of up to 5 mm per hour. For this condition, what is the maximum roof area that can be drained successfully? (c) What is the Reynolds number Rea? Water Tinyland governor's mansion 20 cmarrow_forward
- A pipe inclined at 45° to the horizontal (Fig. 2) converges over a length l of 2 m from a diameterd1 of 200 mm to a diameter d2 of 100 mm at the upper end. Oil of relative density 0.9 flowsthrough the pipe at a mean velocity ?̅1 at the lower end of 2 m/s. Find the pressure differenceacross the 2 m length ignoring any loss of energy, and the difference in level that would beshown on a mercury manometer connected across this length. The relative density of mercury is 13.6 and the leads to the manometer arefilled with the oil.arrow_forwardThe streamlines in a particular two-dimensional flow field are all concentric circles, as shown in Fig. 5 the equation v, = wr where w is the angular velocity of the rotating mass of fluid. Determine the circulation around the path ABCD. The velocity is given by B Figure 5arrow_forwardThe cylindrical container in Fig. is 20 cm in diameterand has a conical contraction at the bottom with an exithole 3 cm in diameter. The tank contains fresh water atstandard sea-level conditions. If the water surface is fallingat the nearly steady rate dh/dt ≈ - 0.072 m/s, estimate theaverage velocity V out of the bottom exit.arrow_forward
- fluid2.pdf -> Example 2 • Water is flowing from hole 1cm radius at the bottom of a closed cylindrical container of 2m diameter. If the height of the water in the container is 2 m and the pressure over the surface of water is 3 atm. calculate how much time it took until the container became empty? P.arrow_forwardThe reservoirs in Fig. contains water at 208C. If thepipe is smooth with L = 4500 m and d = 4 cm, what willthe flow rate in m3/h be for Dz =100 m?arrow_forwardTorricelli problem. A tank whose shape is obtained by rotating y = x6. At t = 0, the water height is y = 2. The hole at the bottom is of area a = 0.05m2. The gravity acceleration is g = 9.8m/s2. How long will it take for all the water to drain from the tank?arrow_forward
- The pump in Fig. draws gasoline at 20 ° C from areservoir. Pumps are in big trouble if the liquid vaporizes(cavitates) before it enters the pump. ( a ) Neglecting lossesand assuming a fl ow rate of 65 gal/min, fi nd the limitationson ( x , y , z ) for avoiding cavitation. ( b ) If pipe frictionlosses are included, what additional limitations might beimportant?arrow_forwardExample(1) Consider the water siphon shown in Fig. below. Assuming that Bernoulli's equation is valid, (a) find an expression for the velocity V2 exiting the siphon tube. (b) If the tube is 1 cm in diameter and z = 60 cm, z2 =25 cm, estimate the flow rate in m²/s. Estimate the pressure at point(3) if 23=90cw z =0---- V2 НОНЕWORК Estimate the pressure at point (3 ) if Z3= 90cm.arrow_forwardThe 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
8.01x - Lect 27 - Fluid Mechanics, Hydrostatics, Pascal's Principle, Atmosph. Pressure; Author: Lectures by Walter Lewin. They will make you ♥ Physics.;https://www.youtube.com/watch?v=O_HQklhIlwQ;License: Standard YouTube License, CC-BY
Dynamics of Fluid Flow - Introduction; Author: Tutorials Point (India) Ltd.;https://www.youtube.com/watch?v=djx9jlkYAt4;License: Standard Youtube License