Construction Materials, Methods and Techniques (MindTap Course List)
4th Edition
ISBN: 9781305086272
Author: William P. Spence, Eva Kultermann
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 3, Problem 7RQ
To determine
The factor describing the overall thermal performance of a building
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
important considerations that are relevant to meet the feasibility of building a piezoelectric tile prototype for the generation of electrical energy by pedestrian traffic.
What is latent heat of vaporization?
3.
6.0" wide wooden fence posts are embedded in a concrete driveway a distance 12.125" apart. There is
a 1/16" gap between the post and the concrete (see diagram). The posts are installed when the temperature is
12°C. Determine if the gap will close when the temperature increases to 32°C and if not how big the gap will
be at that temperature. The thermal expansion coefficients of wood and concrete are awood =32 x 105 °C and
aconcrete =13 x 106 °C. 1 inch3D2.54 cm.
6.0"
12.0"
0.0625"
Chapter 3 Solutions
Construction Materials, Methods and Techniques (MindTap Course List)
Ch. 3 - What are the major material groups?Ch. 3 - Prob. 2RQCh. 3 - What are the mechanical properties that define a...Ch. 3 - How does a tensile stress differ from a...Ch. 3 - Prob. 5RQCh. 3 - Prob. 6RQCh. 3 - Prob. 7RQCh. 3 - What is the most common form of chemical...Ch. 3 - Prob. 9RQCh. 3 - Prob. 10RQ
Knowledge Booster
Similar questions
- A line measured with a 50-m long steel tape was determined to be 645.22 meter when the average temperature during taping was 15.750C. If the tape is of standard length at 200C and the coefficient of thermal expansion of steel is 0.0000116/10C, the correct length of the measured line isarrow_forwardDefine contacting power in wet scrubbers? How is it related to scrubber efficiency ?arrow_forwardExplane of Heat Treatment.arrow_forward
- Urgent..... Classify the following materials with regard to their thermal insulation properties, rate them from the best to the worst: Solid concrete block, Burned clay block, clay brick. Cement - sand bricks, light weight blocks, and hollow concrete blocks.arrow_forwardPractical applications and significance of energy loss in pipes. Please also give one real life engineering application.arrow_forwardA 1,065 ft², 7 in. thick concrete wall has inside and outside surface temperatures of 25°C and 9°C. A 2 in. insulation batt with a thermal conductivity of k = 0.03 Btu/(h· ft· °F) is added to the wall. Determine the reduction in heat transfer rate. What is the thickness of the insulation in meters? m What is the thermal conductivity value of the insulation batt in W/(m .K)? W/(mK) What is the R-value of the concrete wall (in m². K/W)? m². K/W What is the R-value of the insulation batt (in m². K/W)? m². K/W What is the heat transfer rate (in W) when the insulation is added? W What is the percent reduction in the heat transfer rate? %arrow_forward
- Calculate the thickness of the masonry wall having thermalconductivity of 0.75 W/mK if the heat transfer is to be 80% of theheat transfer through a composite structural wall having athermal conductivity of 0.25 W/mK and a thickness of 100mm.Assume that both walls are subjected to same surfacetemperature.arrow_forwardSuppose you were to build a bridge in the state of Texas. Look over some of the specific heat values for typical building materials. What material do you think you should use when building a bridge here? Why?arrow_forward80° -Sheathing 70° Gypsum wallboard 60° Fiberglass between studs Siding 50° Air inside room 40° at 72F Air outside at 0F 30° 20° 10° 0 1 2 3 4 5 6 7 Distance through wall (inches) The temperature changes in the wall - Insulation According to the figure materials is the best insulator? The poorest? Explain. which of the Temperature (°F)arrow_forward
- Explain what is meant by permeability and describe how to interpret the permeability ratings of vapor retarders.arrow_forwardQuestion 11 Which statement about thermal conductivity is FALSE? O a. The thermal conductivity of timber is greater in the longitudinal compared to the radial direction. O b. Lower density results in lower thermal conductivity. C. Thermal modification of wood reduces its thermal conductivity. Od. Thermal conductivity of air is higher compared to wood.arrow_forwardThe heat loss, in Btu/hr, for two different types of walls is given. Find in Btu/hrthe difference in the heat losses.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Construction Materials, Methods and Techniques (M...Civil EngineeringISBN:9781305086272Author:William P. Spence, Eva KultermannPublisher:Cengage Learning
Construction Materials, Methods and Techniques (M...
Civil Engineering
ISBN:9781305086272
Author:William P. Spence, Eva Kultermann
Publisher:Cengage Learning