Welding: Principles and Applications (MindTap Course List)
8th Edition
ISBN: 9781305494695
Author: Larry Jeffus
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 18, Problem 6R
What are the common causes of a concave root surface?
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
b) Based in the stuck pipe case in the last page answer the
following questions:
i. What do you consider the Stuck Pipe Mechanism is?
ii. What contributed to these Stuck Pipe Incidents and
explain the root cause?
iii. Was the correct freeing method applied?
iv. What information do you need to be able to advise your
preferred action plan?
v. Would you attempt to free?
(3 marks)
Well Data:-
Hole Size / Depth AH : 5-7/8" - 3526 m MD
Pump Rate 1050 Ipm
Mud: KCVPAC, 1.38 kg/l, PV/YP:14/25, WL:3.9 ml
Formation : Sand/Siltstone (3021 m), Limestone (3085
m)
Claystone (3109 m), Sandstone (3215 m)
Csa/Well Trajectory/BHA:
7" casing shoe: 2885 m MD, 39 deg, the steady drop from
39 deg to 8 deg at 3400 m
BHA - Drilling: Bit, NBS, ShockSub, SS, MWD, NMSS,
NMDC, SS, Circ.Sub, 3DC, SS, 3DC, SS, 3DC, Lo-Torg
subs, DC, Jar, DC, HDWP
Brief Well History:-
Drilled 5-7/8" hole with mudmotor from 2612-3406 m. Took
survey (8 deg incl). POH, backreamed all tight spots.
RIH with rotary BHA and encountered…
. How can discontinuities in the root face be removed?
What is the Minor Loss Coefficient(k-value) of one 45 Degree Elbow using the following data?
Chapter 18 Solutions
Welding: Principles and Applications (MindTap Course List)
Ch. 18 - What types of industries require GTAW-quality pipe...Ch. 18 - What are the grooves most often used for welding...Ch. 18 - What condition must the prepared edges of a pipe...Ch. 18 - How is the depth of root penetration measured?Ch. 18 - What problem can incomplete fusion cause?Ch. 18 - What are the common causes of a concave root...Ch. 18 - What problems can excessive root reinforcement...Ch. 18 - Prob. 8RCh. 18 - What gases are used as backing gases?Ch. 18 - How long would it take to purge a 15-ft section of...
Ch. 18 - How long would it take to purge a 10-mm section of...Ch. 18 - How can filler metal be added to make a root pass?Ch. 18 - Prob. 13RCh. 18 - How is the tack weld ended so that it will not...Ch. 18 - What is the 1G pipe position?Ch. 18 - After the weld is set up and ready to begin, how...Ch. 18 - What type of weld can be made using the nozzle...Ch. 18 - What two problems can be corrected by a hot pass?Ch. 18 - Why must you brace yourself when making a weld?Ch. 18 - What can happen to the weld pool if the torch...Ch. 18 - What technique should be used when stopping a...Ch. 18 - What is the maximum width that a weave pattern...Ch. 18 - Why should the filler pass penetration be limited...Ch. 18 - How much filler metal should be added to a filler...Ch. 18 - What is the 5G pipe position?Ch. 18 - How should the torch be held to allow good...Ch. 18 - Why are stringer beads in the 6G position kept...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Detailed and complete solutionarrow_forwardExplain some Modification Factors for Footing Depth ?arrow_forwardHigh ash content that deposit on inlet fixed blades: Choose the right answer Reduces the gas flow and increase the output power Reduces the gas flow and output power All answers are correct Increase both the gas flow and output powerarrow_forward
- Plz complete and correct solution I vill definitely upvotearrow_forward(ii) List the benefits of good maintenance? (any threearrow_forwardMost cement slurries will contain some additives to modify the properties of the slurry to produce a better cement job to suit particular requirements. Fluid loss is not the water lost from cement slurry to the formation during slurry placements. a. False b. Truearrow_forward
- How is the moment area method applied to statically indeterminate beams and shafts?arrow_forwardWhich of the following is not the drilling hazard? a. Pipe stuck b. Tools dropped while drilling c. Increased bit life d. Sloughing shale e. Lost circulation problems f. Increased size of holearrow_forwardWater jet cutting is one of several ways of cutting or trimming uncured or cured FRPS; in the case of cured FRPS, the process is noted for its reduction of dust and noise Select one: True Falsearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Surface Finish Measurement - Skidded VS. Skidless Surface Roughness Measurement; Author: Mitutoyo America Corporation;https://www.youtube.com/watch?v=X7jCTIwVs80;License: Standard Youtube License