Applied Statics and Strength of Materials (6th Edition)
6th Edition
ISBN: 9780133840544
Author: George F. Limbrunner, Craig D'Allaird, Leonard Spiegel
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 12, Problem 12.18P
If the shaft of Problem 12.17 were solid, with the same outside diameter and stressed to the same maximum shear stress, what would be the angle of twist? Compute the percentage increase in torque that the solid shaft could transmit. Compute the percentage increase in weight (use a unit weight of steel of
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Compute the torsional shear stress in a circular shaft with diameter of 50mm that is subjected to a torque of 800Nm.
A shaft is designed to transmit power of 100 kW at 180 rpm. The allowable shear stress is 50MPa and modulus of rigidity of 80 GPa. The angle of twist is not to exceed to 1° in 4-meter length
A. Calculate the diameter of the shaft in inches.
B.If the shaft in A is to be fitted to a hub with material SAE 0105 and fit classification of FN3, what will be the maximum and minimum stresses based on the interference of metal.
A circular shaft of 60 mm diameter is running
at 150 r.p.m. What will be the torque
transmitted by the shaft if (t = 80 MPa)?
Chapter 12 Solutions
Applied Statics and Strength of Materials (6th Edition)
Ch. 12 - Determine the internal resisting torque in the...Ch. 12 - Determine the internal resisting torque in the...Ch. 12 - Calculate the maximum shear stress developed in a...Ch. 12 - Calculate the allowable torque for a hollow steel...Ch. 12 - Calculate the allowable torque that may be applied...Ch. 12 - A hollow circular steel shaft has a 100-mm outside...Ch. 12 - Design a solid circular steel shaft to transmit an...Ch. 12 - Calculate the shear stresses at the outer and...Ch. 12 - A hollow shaft is produced by boring a...Ch. 12 - Pulleys C and D are attached to shaft AB, as...
Ch. 12 - Calculate the angle of twist a 3-in-diameter...Ch. 12 - Calculate the angle of twist a 65-mm-diameter...Ch. 12 - Calculate the angle of twist a 4-in.-diameter...Ch. 12 - Prob. 12.14PCh. 12 - Prob. 12.15PCh. 12 - A solid steel shaft is to resist a torque of 9000...Ch. 12 - A hollow steel shaft has a 50-mm outside diameter...Ch. 12 - If the shaft of Problem 12.17 were solid, with the...Ch. 12 - An automobile engine develops 90 hp at 3500 rpm....Ch. 12 - Calculate the speed (rpm) at which a...Ch. 12 - Select the diameter of a solid circular steel...Ch. 12 - Select the diameter for a hollow steel shaft that...Ch. 12 - A 6-ft-long solid steel shaft with a diameter of 4...Ch. 12 - The outside and inside diameters of a hollow steel...Ch. 12 - Calculate the maximum shear stress developed in a...Ch. 12 - Write a program that will calculate the allowable...Ch. 12 - Write a program that will generate a table of...Ch. 12 - Rework the program of Problem 12.27 using SI...Ch. 12 - Write a program that will generate a table of...Ch. 12 - Compute the maximum shear stress in the hollow...Ch. 12 - Calculate the allowable torque that may be applied...Ch. 12 - Design a hollow steel shaft to transmit a torque...Ch. 12 - A 32-in.-long solid steel circular shaft, 3 in. in...Ch. 12 - The 65-mm-diameter solid shaft shown is subjected...Ch. 12 - Rework Problem 12.34, changing the diameter of...Ch. 12 - Compute the maximum shear stress in the circular...Ch. 12 - Determine the allowable torque a hollow steel...Ch. 12 - A 1.00-m-long steel wire, 4 mm in diameter, is...Ch. 12 - Select the outside and inside diameters for a...Ch. 12 - A solid aluminum shaft, 6 ft in length, is to...Ch. 12 - A 25-mm-diameter solid shaft with an allowable...Ch. 12 - Compute a. the maximum shear stress developed in a...Ch. 12 - What horsepower can a solid steel shaft 6 in. in...Ch. 12 - Calculate the maximum power that may be...Ch. 12 - A small ski lift has a main cable driving wheel 11...Ch. 12 - A 32-mm-diameter solid shaft transmits 100 kW of...Ch. 12 - A solid steel shaft is to transmit power of 58 kW...Ch. 12 - Select the diameter for a solid steel shaft that...Ch. 12 - A solid steel shaft is to transmit 100 hp at a...Ch. 12 - Two shafts-one a hollow steel shaft with an...Ch. 12 - A 112 -in.-diameter solid steel shaft is 40 ft in...Ch. 12 - A solid steel shaft is to transmit 120 hp. The...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Compute for the normal shear stress in ksi for a 3.1 inch diameter shaft that is subjected to a torque of 500ft lbf.arrow_forwardA solid steel shaft is to transmit 120hp. The allowable shear stress is 8,000 psi. Calculate the diameter if the shaft speed is 3000 rpm.arrow_forwardCompute the torsional shear stress in a circular shaftwith a diameter of 50 mm that is subjected to a torqueof 800 Nmarrow_forward
- Compute the torsional shear stress that would be produced in a solid circular shaft having a diameter of 20 mm whe subjected to a torque of 280 N m.arrow_forwardAn engine develops 5.0 MW at 115 RPM and the ratio of maximum to mean torques is 1.3 to 1. Calculate the diameter (in mm) of the main shaft coupled direct to the engine to transmit the power 1. а. allowing a stress of 50 MPa and assuming the shaft to be solid. b. Calculate the diameter (in mm) of the main shaft coupled direct to the engine to transmit the power allowing a stress of 50 MPa and assuming the hollow with a bore equal to half the outside diameter. For Solid Shaft:T: = D't For Hollow Shaft:T= 16 16D Tm = P/warrow_forwardA solid circular shaft is subjected to a torque of 21,334 in-lb. Calculate the diameter required if the allowable twist is 1.7° per foot, and the material is steel alloy which has a modulus of rigidity of 12,000,000 psi.arrow_forward
- A circular steel shaft of diameter 30 mm is subjected to a torque of 60 N-m. Calculate the angle of twist if the length of the shaft is 20 m.arrow_forwardDesign a hollow circular steel shaft to transmit an applied torque of 360,000 in-lbs. Theallowable shear stress is 6,000 psi and the inside diameter is to be 0.6 times the outsidediameter.arrow_forwardA hollow shaft with a length of 1103mm and outer diameter 73mm and inner diameter 50mm is required to tranmit a power of 60kW at a speed of 2950 rpm if the modulus of rigidity is 79.5GPa calculate the angle of twist in degreesarrow_forward
- A hollow shaft must transmit 1400 kW at 180 rpm. The outside diameter must be 1.6 times the inside diameter. The maximum torque is 30% more than the mean torque. Calculate: 1. The diameters of the hollow shaft if the allowable stress is 200 MPa. 2. The diameter of the solid shaft if the allowable stress is 200 MPa.arrow_forwardDesign the outside and inside diameters for a hollow stell shaft subjected to a torque of 1,000,000 in-lb. The maximum shear stress developed in the shaft is not to exceed 8,000 psi. The inside diameter is to be 2/3 of the outside diameter. Calculate the angle of twist in degrees for a 14 foot length of this shaft. Answer: D(outside) = 9.259 inches, D(inside) = 6.176 inches, angle of twist= 1.39 degrees I'm unsure of how to solve this problem. Could someone help me walk through the process step-by-step? Thanks in advance.arrow_forwarda) Compute the torsional shear stress in a circular shaft with a diameter of 50 mm that is subjected to a torque of 800 N.m. b)If the shaft of Problem above is 850 mm long and is made of steel, compute the angle of twist of one end in relation to the other.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Everything About COMBINED LOADING in 10 Minutes! Mechanics of Materials; Author: Less Boring Lectures;https://www.youtube.com/watch?v=N-PlI900hSg;License: Standard youtube license