Fundamentals of Aerodynamics
6th Edition
ISBN: 9781259129919
Author: John D. Anderson Jr.
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 1, Problem 1.19P
For the design of their gliders in 1900 and 1901, the Wright brothers used the Lilienthal Table given in Figure 1.65 for their aerodynamic data. Based on these data, they chose a design angle of attack of 3 degrees, and made all their calculations of size, weight, etc., based on this design angle of attack. Why do you think they chose three degrees?
Hint: From the table, calculate the ratio of lift to drag, L/D, at 3 degrees angle of attack, and compare this with the lift-to-drag ratio at other angles of attack. You might want to review the design box at the end of Section 1.8, especially Figure 1.36, for the importance of L/D.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A light truck weighs 3,300 lb and is rated at 30 miles per gallon for 52 mph highway driving on level ground. Under those conditions, the engine must overcome air resistance, rolling resistance, and other sources of friction. Give your answers in the units shown.
(a) The coefficient of drag is 0.55 at 52 mph, and the truck's frontal area is 28 ft?. What is the drag force on the truck?
(Express your answer using three significant figures.)
F =
lb
(b) How much power must the engine produce at 52 mph just to overcome air resistance?
(Express your answer using three significant figures.)
P =
|hp
(c) In part (b) how much gasoline would be consumed each hour (neglecting other frictional effects)?
(Express your answer using three significant figures.)
V =
gal
The drag polar equation of a light airplane in clean configuration can be written as Cp = 0.358 +
0.0405 C₁². It has a weight of 18,681 N. The wing area is 14.41 m². Calculate the minimum
power required in watts.
(Round off answer with no decimal places, No units, No commas)
Answer given:
1461792
A 5,000 lbs. aircraft has an excess power of 75 hp at sea level. If the service ceiling is 3,657.6
m, determine the time to climb from sea level to absolute ceiling in minutes.
(Round off answer with no decimal places. No units, No commas)
Answer given:
17
1. A piston-prop aircraft has a wing loading of 1600 N/m², wing area of 25 m² and
its drag polar is given by Cp
1.5. The reciprocating engine develops 750 kW at sea level, and the propulsive
efficiency of the engine-propeller combination is 0.85. Draw the power-available
and power-required curves at sea level. Determine the maximum and minimum
speeds for level flight at sea level. What is the minimum power required for level
flight at sea level? Determine the corresponding velocity and lift coefficient.
0.025 + 0.05C. The maximum lift coefficient is
Chapter 1 Solutions
Fundamentals of Aerodynamics
Ch. 1 - For most gases at standard or near standard...Ch. 1 - Starting with Equations (1.7),(1.8), and (1.11),...Ch. 1 - Consider an infinitely thin flat plate of chord c...Ch. 1 - Consider an infinitely thin flat plate with a 1 m...Ch. 1 - Consider an airfoil at 12 angle of attack. The...Ch. 1 - Consider an NACA 2412 airfoil (the meaning of the...Ch. 1 - The drag on the hull of a ship depends in part on...Ch. 1 - The shock waves on a vehicle in supersonic flight...Ch. 1 - Consider two different flows over geometrically...Ch. 1 - Consider a Lear jet flying at a velocity of 250...
Ch. 1 - A U-tube mercury manometer is used to measure the...Ch. 1 - The German Zeppeins of World War I were dirigibles...Ch. 1 - Consider a circular cylinder in a hypersonic flow,...Ch. 1 - Derive Archimedes principle using a body of...Ch. 1 - Consider a light, single-engine, propeller-driven...Ch. 1 - Consider a flat plate at zero angle of attack in a...Ch. 1 - Consider the Space Shuttle during its atmospheric...Ch. 1 - The purpose of this problem is to give you a feel...Ch. 1 - For the design of their gliders in 1900 and 1901,...Ch. 1 - Consider the existence of a forward-facing axial...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Locate the centroid of the area. Prob. 9-17
Engineering Mechanics: Statics
Select a mechanical component from Part 3 of this book (roller bearings, springs, etc.), go to the Internet, an...
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
The triple jump is a track-and-field event in which an athlete gets a running start and tries to leap as far as...
Vector Mechanics For Engineers
Assume the following vectors are already defined: V1=[302]V2=[214]V3=[5131]V4=[0.50.10.20.2] For each of the fo...
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Determine the length of the cantilevered beam so that the maximum bending stress in the beam is equivalent to t...
Mechanics of Materials (10th Edition)
The moment of inertia Iy for the slender rod in terms of the rod’s total mass m .
Engineering Mechanics: Statics & Dynamics (14th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- QUESTION 2 A streamlined experimental solar car has a frontal area of 0.48 m² and an expected coefficient of drag of 0.12. The car and driver have a total mass of 200 kg. What is the maximum speed that could be expected if the maximum power available from its electric motor is 350 W? Assume a rolling resistance coefficient of 0.015. Take the density of air as 1.21 kg/m³.arrow_forward2. The table below shows experimental data for the shape and pressure distribution on the upper and lower surface of an airfoil at zero angle of attack. X 0 0.25 0.5 0.75 1 Y Fx = Yu 0 0.0952 0.0922 0.0588 0 (Pu dYu dx - Calculate the drag and lift force on the airfoil by numerically evaluating the integrals Fy (P₁-P₂)dx = √ ( P₁ - 1 Pi Y₁ 0 -0.0254 -0.0144 -0.0052 0 dv) Y = Yu (x) dx y = Ye (x) Pu 1.000 -1.640 -0.786 -0.212 0 x Pi 1.000 0.589 0.426 0.322 0 Use finite difference approximations of the derivatives and the composite Simpson's rule to evaluate the integrals. Hint: Use central differences to estimate the derivatives wherever possible since they are more accurate than forward or backward differences.arrow_forwardIf the pressure difference in the wind tunnel experiment is 50 mmH,O, the density of air is 1.2 3 kg/m in wind tunnel experiment, and the airfoil span is 204 mm, and the cord length is 98 mm, what is the lift coefficient if the lift force is L=28.9 N Select one: a. 2.94715 b. 11.61715 c. 5.83715 d. 14.50715 e. 8.72715arrow_forward
- (a) A luxury sports car has a frontal area of 23.1 ft and a 0.24 coefficient of drag at 80 mph. How much power must the engine produce just to overcome the air drag? (Express your answer using three significant figures.) P = hp (b) A sport-utility vehicle has Cp = 0.45 at 80 mph and a slightly larger frontal area of 28.3 ft. How much power must the engine produce just to overcome the air drag? (Express your answer using three significant figures.) P =[ hparrow_forwardFor a new sailboat, a designer wants to determine the drag force that may be expected at a given speed. To do so, she places a model of the proposed hull in a test channel and uses three cables to keep its bow on the centerline of the channel. Dynamometer readings indicate that for a given speed, the tension is 40 lb in cable AB and 60 lb in cable AE. Determine the drag force exerted on the hull and the tension in cable AC.arrow_forwardWhat is the total coefficient of a drag if at the maximum CL/Cd, the lift created is 60 lbs? The speed of the aircraft is 20 mph, and the area of the elliptical wing is 70 ft^2. The span of the wing is 20 ft. Assume standard sea level conditions.arrow_forward
- Qustion. An aircraft is flying in level flight at a speed of 200 km/h through air (density, p = 1.2 kg/m³, and viscosity, μ = 1.6 x 10-5 N-s/m²). The lift coefficient at this speed is 0.4 and the drag coefficient is 0.0065. The mass of the aircraft is 800 kg. The effective lift area of the aircraft NOTE= Do not give wrong answer I will dislike , If not sure skip itarrow_forwardThe maximum lift-to-drag ratio of a 600,000 lb aircraft is 18.7. The Thrust Specific Fuel Consumption (TSFC) = 0.85 (lbs/hr)/lb. The total fuel on board is Wf = 180,000 lbs. Find the maximum endurance of the aircraft in hours. Round off your answer in ones place. Answer for a thumbs uparrow_forwardA smooth aluminum sphere hangs in air on a 0.5 m-long cable. The sphere has a diameter of 10 cm and weighs 1.5 N (it is hollow). It is observed that a steady wind causes the sphere and cable to be displaced so that = 20°. Assume that the weight of the cable and the drag force on the cable are negligible. (a) What is the magnitude of the (horizontal) drag force on the sphere? (b) What is the wind speed U? Answer: (a) D≈ 0.55 N, (b) U≈ 15 m/s Uarrow_forward
- For a new sailboat, a designer wants to determine the drag force that may be expected at a given speed. To do so, she places a model of the proposed hull in a test channel and uses three cables to keep its bow on the center-line of the channel. Dynamometer readings indicate that for a given speed, the tension is 35 lb in cable AB and 40 lb in cable AE. The drag force is exerted in the direction of Flow at point A. –7 ft - B E1.5 ft 4 ft Flow A 4 ft E What is the magnitude of the drag force in Ib? What is the magnitude of the tension force in cable AC in Ib? What is the angle a in degrees measured CCW from the vertical? What is the angle B in degrees measured CW from the vertical?arrow_forwardProblem 3 - A small airplane that has a mass of 1,500 lb,m is about to take off. The airplane has a coefficient of lift of 1.0 at an Angle of Attack (AOA) of zero and it linearly increases by 0.1 every 10 degrees; wings with a constant chord length of 3.5 ft and a total wingspan of 30 ft; a coefficient of drag of 0.3; and a frontal area of 40 ft? that linearly increases by 5 ft every 10 degrees. If the air is still, and the density of air is 0.076 lbm ft-3 at the ground level what is the critical speed needed for takeoff? If the runway is 1000 ft long, the total coefficient of friction between the road and the airplane is 0.25, what is the average thrust needed to achieve the critical takeoff speed?arrow_forwardThe figure shows two cables AB and AC. Using the tabulated values for the parameters, calculate the magnitude of the projection of FAC onto AB. Also, determine the angle 0 formed by BAC. NOTE: the magnitude of the projection may be positive or negative (or zero). Also, point C lies on the y axis. В L6 FAB A L2 FAC y L3 X 2021 Cathy Zupke parameter value units 3 m L2 L3 L4 3 m 3 m 1 m 3 L6 FAB 2 80 N FAC 100 The magnitude of the projection of FAC on AB is N The angle AB makes with AC is 0-arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license