using simple logic gates Design Problem A Chemical plant needs a microprocessor-driven alarm system to warn of critical conditions in one of its chemical tanks. The tank has four (HIGH / LOW) switches that monitor: Temperature (T) Pressure (P) Fluid Level (L) Weight (W) Design a system that will notify the microprocessor to activate an alarm when any of the following conditions arise: High Fluid Level with High Temperature and High Pressure Low Fluid Level with High Temperature and High Weight Low Fluid Level with Low Temperature and High Pressure Low Fluid Level with High Temperature and Low Weight

using simple logic gates Design Problem A Chemical plant needs a microprocessor-driven alarm system to warn of critical conditions in one of its chemical tanks. The tank has four (HIGH / LOW) switches that monitor: Temperature (T) Pressure (P) Fluid Level (L) Weight (W) Design a system that will notify the microprocessor to activate an alarm when any of the following conditions arise: High Fluid Level with High Temperature and High Pressure Low Fluid Level with High Temperature and High Weight Low Fluid Level with Low Temperature and High Pressure Low Fluid Level with High Temperature and Low Weight

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter13: Heating Control Devices

Section: Chapter Questions

Problem 30RQ

See similar textbooks

Similar questions

Design an interfacing system for solar controller, your design should monitor the solar system data like solar panels output, energy consumption, battery charging current, etc, the system must have keypad input and LCD display to allow users to view system status and adjust system parameters like max charging current, max consumption load. ...Draw a detailed block diagram of the interfacing system showing all the signals
Question No.3: Consider a microprocessor based board which has 7-segment and Led is connected to it. Design an assembly language code such that input from user is taken; when user presses “1” “5410” should display on 7-seg Display and when user press 2 leds should glow 5 times in a loop. If any other key is pressed no action should be taken
I need some help with the image provided. This is for microcontroller and embeded system. it seems is related to interrupts and it is providing some logical gates. Can someone explain wherever is happening in the image. I only need to grap the concepts nothing really technical
Question: Consider you are asked to design a digital system that controls an electric motor “M". Motor is turned on when logic 0 is applied and turns off when logic 1 is applied. Two identical photo sensors, “S1" and "S2" produce logic 1 when light falls on them and provide logic 0 when light does not fall on them. Motor is to be controlled in such a way when light falls on both sensors, motor turns on. When light falls on S1 only, motor turns on. When light falls on S2 only motor turns off. Motor turns off when both sensors do not receive any light. Perform the following tasks: A. List the truth table. B. Write down the output equation. C. Draw the circuit diagram. D. Implement on Proteus (paste screen shot of implemented circuit).
Q3: Consider a digital counter that counts 5 to 0 when the reset button is 0 and go back to 0 when the reset button is 1. draw the state diagram and state table for the digital control circuit of such a digital counter?
4)A PLC scan cycle contains each of the following operations EXCEPT A)read inputs B)perform diagnostics & communication C)execute logic D)compile installed ladder logic program
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
Can you please help me design some instructions that ze ros the content of the accumulator register? Thanks will thumbs up
An 8051 subroutine is shown below: SUB: RO, #20H @RO , #0 MOV LOOP: MOV INC RO CJNE RO, #80H, LOOP RET a. What does this subroutine do? b. In how many machine cycles does each instruction execute? How many bytes long is each instruction? C. d. Convert the subroutine to machine language. e. How long does this' subroutine take to execute? (Assume 12 M
4.a. What is the name of the nonprogrammable timer that is used to check the internal operation of the PLC?A. HousekeepingB. ScanC. WatchdogD. System4.b. Which one of the following terms is used to define the identifying letters placed above an input contact inladder logic?A. SurnameB. TitleC. StatementD. Locator
Draw the circuit that can represent a parity generator/ parrity error detector Specify the input variables and output for each case. Give a brief explanation.
Answer the following questions using the block diagram given in the figure.a. If the disruptive input is zero, is the system stable (do your operations as Gb(s)= 1)?b. What should Gb(s) be so that the disruptor input B(s) has no effect on the system output?