3. A sequential circuits with two Flip Flops A and B, two inputs x and y, and one output z is specified by the following next-state and output equations. A(t+1) = x' y + x B B(t+1) = x'A + x B Z= A (i) Draw the logic diagram of the circuit. (ii) List the state table for the sequential circuit. (iii) Draw the corresponding state machine diagram.

3. A sequential circuits with two Flip Flops A and B, two inputs x and y, and one output z is specified by the following next-state and output equations. A(t+1) = x' y + x B B(t+1) = x'A + x B Z= A (i) Draw the logic diagram of the circuit. (ii) List the state table for the sequential circuit. (iii) Draw the corresponding state machine diagram.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

4-6. A sequential circuit with two D flip-flops A and B and input X and output Yis specified by the following input equations: Y = A + B D = X + B D = XA (a) Draw the logic diagram of the circuit. (b) Derive the state table. (c) Derive the state diagram. (d) Is this a Mealy or a Moore machine?
Q) You want to design a synchronous counter sequential (sequential) logic circuit. Counting from 9 to 0 and will not count the last digit of your student number. (a) List the steps that you will apply in the design approach. State Chart and State Create the table. (b) Design the sequential circuit using JK Flip-Flop. Explain each step. Desired action show that you have done it. " last digit student num:4 " Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, I want the solution on paper if possible.
Review Questions Question [4] For the given sequential circuit: a. What type of state machine is this circuit and why? b. Determine the flip-flop input equations and the output equations from the circuit. c. Derive the next-state equation for each flip-flop from its input equations. d. Derive the State table. e. Derive the State Graph. Determine the state sequence and output sequence if the initial state is So and the input sequence is X= 01100 B B KA CK JA KB CK to Clock Clock X" X- X' A B'
You want to design a synchronous counter sequential (sequential) logic circuit. It will count from 0 to 9 and will not count the decimal digits in the last two digits of your student number. a. List the process steps that you will apply in the design approach. Create the State Chart and State Chart. b. Design the sequential circuit using JK Flip-Flop. Explain each step. Show that it has performed the desired action. last two numbers 02
Q) You want to design a synchronous counter sequential (sequential) logic circuit. Counting from 0 to 9 and will not count the last two digit of your student number. (a) List the steps that you will apply in the design approach. State Chart and State Create the table. (b) Design the sequential circuit using JK Flip-Flop. Explain each step. Desired action show that you have done it. " last two digit student num: 0 4 " Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, I want the solution on paper if possible.
You want to design a synchronous counter sequential logic circuit. Counting from 0 to 9 will perform and not count the numbers 0, 3, 5, 8. (a) List the steps you will apply in the design approach. State Diagram and Status Create the table. (b) Design the sequential circuit using Flip-Flops. Explain each step. Desired action show that it does.
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
In this assignment, you are required to design a circuit that counts and displays the sequence of the number 010430011092 . The number will then be displayed on a 7-segment display and changed every 1 second. The block diagram is as shown in Figure 1. Construct your design as follow: - (a) Design a combinational logic circuit that converts binary number to a sequence of the number 010430011092 and to be displayed on a single common anode 7-segment display. The logic circuit must be designed using 2-input NAND gate
1. Design a combinational logic circuit that compares two 4-bit numbers A and B. The circuit should output the relation of the two inputs. Use an available TTL IC for the design.
Consider the circuit below. The switches are controlled by logic variables such that, if A is high, switch A is closed, and if A is low, switch A is open. Conversely, if B is high, the switch labeled is open, and if B is low, the switch labeled is closed. The output variable is high if the output voltage is 5V, and the output variable is low if the output voltage is zero. a. Write a logic expression for the output variable. b. Construct the truth table for the circuit. A Logic 1 5V(+ B C Logic 0 R
6. For the follow logic circuit system, the output f is: 5 (A) ab. (B) a + b. (C) a'+b'. (D) a'b'. a b
Design a combinational circuit using multiplexer for a car chime based on thefollowing system: A car chime or bell will sound if the output of the logic circuit(X) is set to a logic ‘1’. The chime is to be sounded for either of the followingconditions:• if the headlights are left on when the engine is turned off and• if the engine is off and the key is in the ignition when the door is opened.Use the following input names and nomenclature in the design process:• ‘E’ – Engine. ‘1’ if the engine is ON and ‘0’ if the engine is OFF• ‘L’ – Lights. ‘1’ if the lights are ON and ‘0’ if the lights are OFF• ‘K’ – Key. ‘1’ if the key is in the ignition and ‘0’ if the key is not in the ignition• ‘D’ – Door. ‘1’ the door is open and ‘0’ if the door is closed• ‘X’ – Output to Chime. ‘1’ is chime is ON and ‘0’ if chime is OFF