The control rod AC is guided by two pins that slide freely in parallel curved slots of radius 199 mm. The rod has a mass of 9.9 kg, and its mass center is located at point G. Knowing that for the position shown the vertical component of the velocity of Cis 1.23 m/s upward and the vertical component of the acceleration of C is 4.97 m/s² upward, determine the magnitude of the force P. P= | (N) 60° G 60°

The control rod AC is guided by two pins that slide freely in parallel curved slots of radius 199 mm. The rod has a mass of 9.9 kg, and its mass center is located at point G. Knowing that for the position shown the vertical component of the velocity of Cis 1.23 m/s upward and the vertical component of the acceleration of C is 4.97 m/s² upward, determine the magnitude of the force P. P= | (N) 60° G 60°

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

16.11 An 8-lb uniform slender rod AB is held in position by two ropes and the link CA which has a negligible weight. After rope BD is cut the assembly rotates in a vertical plane under the combined effect of gravity and 4 lb-ft couple M applied to link CA as shown. Determine, immediately rope BD has been cut, (a) the acceleration of rod AB, (b) the tension in rope EB. after 1.5 ft 60% Fig. P16.11 and P16.12 60 BD
The 10-in.-radius brake drum is attached to a larger flywheel which is not shown. The total mass moment of inertia of the flywheel and drum is 22 lb ⋅ ft ⋅ s 2 and the coefficient of kinetic friction between the drum and the brake shoe is 0.41. Knowing that the initial angular velocity is 255 rpm clockwise, determine the force which must be exerted by the hydraulic cylinder at point B if the system is to stop in 85 revolutions.
The 10-in.-radius brake drum is attached to a larger flywheel which is not shown. The total mass moment of inertia of the flywheel and drum is 22 lb ⋅ ft ⋅ s 2 and the coefficient of kinetic friction between the drum and the brake shoe is 0.41. Knowing that the initial angular velocity is 255 rpm clockwise, determine the force which must be exerted by the hydraulic cylinder at point B if the system is to stop in 85 revolutions. determine the force which must be exerted by the hydraulic cylinder at point B if the system is to stop in 85 revolutions. DO NOT ROUND OFF IN THE SOLUTION. ROUND OFF ONLY IN 2 DECIMAL PLACE IN THE FINAL ANSWER.
A 9-kg uniform disk is attached to the 5-kg slender rod AB by means of frictionless pins at B and C. The assembly rotates in a vertical plane under the combined effect of gravity and of a couple M that is applied to rod AB. Knowing that at the instant shown the assembly has an angular velocity of 6 rad/s and an angular acceleration of 25 rad/s2 , both counterclockwise, determine (a) the couple M, (b) the force exerted by pin C on member AB
The 10-in.-radius brake drum is attached to a larger flywheel which is not shown. The total mass moment of inertia of the flywheel and drum is 22 lb ⋅ ft ⋅ s 2 and the coefficient of kinetic friction between the drum and the brake shoe is 0.41. Knowing that the initial angular velocity is 255 rpm clockwise, determine the force which must be exerted by the hydraulic cylinder at point B if the system is to stop in 85 revolutions. DO NOT ROUND OFF IN THE SOLUTION. ROUND OFF ONLY THE FINAL ANSWER
5. AS-kg uniform disk is attached to the 3-kg uniform rod BC by means of a frictionless pin AB. An elastic cord is wound around the edge of the disk and is attached to a ring at E. Both ring E and rod BC can rotate freely about the vertical shaft. Knowing that the system is released from rest when the tension in the elastic cord is 15 N, determine (a) the angular acceleration of the disk, (b) the acceleration of the center of the disk. 150 mim C E B 75 mmA D
Two identical 4-lb slender rods AB and BC are connected by a pin at B and by the cord AC. The assembly rotates in a vertical plane under the combined effect of gravity and a 6-lb·ft couple M applied to rod AB. Knowing that in the position shown the angular velocity of the assembly is zero, determine (a) the angular acceleration of the assembly, (b) the tension in cord AC.
PROBLEM 4.1 The wheel of an automobile revolves at the rate of 700 rpm. How fast does it move in kilometre per hour, if the radius of its wheel is 250 mm. 6.09 kph 5.09 kph 1. c. 7.09 kph d. 8.09 kph а. b.
PROBLEM 16.18 A prototype rotating bicycle rack is designed to save space at a train station. The combined weight of platform BD and the bicycle is 40 lbs and is centered at 1 ft. above the midpoint of the platform. The motor at A causes the support beam AB to have an angular velocity of 10 rpm and zero angular acceleration at 0= 60°. At this instant, determine the vertical components of the forces exerted on platform BD by the pins at B and D.
Figure 2: Schematic for Question 2. A uniform slender rod of length L = 900 mm and mass m = 4 kg is suspended from a hinge at C. A horizontal force P of magnitude 75 N is applied at end B. Knowing that r = 225 mm, determine (a) the angular acceleration of the rod (b) the components of the reaction at C (c) the distance r for which the horizontal component of the reaction at C is zero (d) the corresponding angular acceleration of the rod
The 8-in. radius brake drum is attached to a larger flywheel that is not shown. The total mass moment of inertia of the drum and the flywheel is 15 lb.ft.s2 and the coefficient of kinetic friction between the drum and the brake shoe is 0.40. Knowing that the angular velocity of the flywheel is 450 rpm clockwise when a force P of magnitude 65 lbf. is applied to the pedal C, determine the number of the revolutions executed by the flywheel before it comes to rest. (The final answer should be in two decimal places with correct units)
A uniform semicircular plate with a mass of 6 kg is suspended from three vertical wires at points A, B, and C, and a force P with a magnitude of 5 N is applied to point B. Immediately after P is applied, determine the acceleration of (a) the mass center of the plate, (b) point C.