Required information Rod BD is made of steel (E = 29 x 106 psi) and is used to brace the axially compressed member ABC. The maximum force that can be developed in member BD is 0.014P. If the stress in BD must not exceed 34 ksi and the maximum change in length of BD must not exceed 0.0009 times the length of ABC, determine the allowable diameter rod that can be used for member BD. Take P = 106 kips. 72 in 72 in 34 in

Required information Rod BD is made of steel (E = 29 x 106 psi) and is used to brace the axially compressed member ABC. The maximum force that can be developed in member BD is 0.014P. If the stress in BD must not exceed 34 ksi and the maximum change in length of BD must not exceed 0.0009 times the length of ABC, determine the allowable diameter rod that can be used for member BD. Take P = 106 kips. 72 in 72 in 34 in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless pully at D. If the allowable tensile stress oallow = 5.2 ksi for the cable, determine the required minimum diameter (inch) of the cable. The cylinder (connected at C) weighs 890 lb. Neglect weight and thickness of the bar AC. D 4 3 A C 5 ft 5 ft -4 ft 890 lb
Required information Rod BD is made of steel (E-29 106 psi) and is used to brace the axially compressed member ABC. The maximum force that can be developed in member BD is 0.018P. If the stress in BD must not exceed 36 ksi and the maximum change in length of BD must not exceed 0.0002 times the length of ABC, determine the allowable diameter rod that can be used for member BD. Take P - 110 kips. 72 in 54 in If stress in member BD should not exceed 36 (ksi), then the diameter of rod BD d 0.0288 (in) 2
Rod BD is made of steel (E = 29 × 106 psi) and is used to brace the axially compressed member ABC. The maximum force that can be developed in member BD is 0.02P. If the stress must not exceed 18 ksi and the maximum change in length of BD must not exceed 0.001 times the length of ABC, determine the smallest-diameter rod that can be used for member BD. Take P = 148 kips.The smallest-diameter rod that can be used for member BD is in.
Link AB is to be made of steel for which the normal stress is 450 MPa. Determine the cross-sectional area of AB. Assume that the link will be adequately reinforced around the pins at A and B. draw free-body diagram
The horizontal bar ABC is supported by a pin at A and the two rods with identical lengths and cross-sectional areas (2 sg.in.) The rod at B is steel and the rod at C is aluminum. Neglecting the weight of the bar, determine the stress in the steel rod when the force W= 10 kips is applied. Use Es=29 x 10^6 psi and Ea=10 x 10^6 psi. Express your final answer in psi to the nearest whole number. Note: Do not include the unit in your answer. * 3 ft B A 5.5ft 1.5 ft →
The cylindrical steel column has an outer diameter of 4 in. and inner diameter of 3.5 in. The column is separated from the concrete foundation by a square bearing plate. The working compressive stress is 26 000 psi for the column, and the working bearing stress is 1200 psi for concrete. Find the largest force P that can be applied to the column. Express your answer in Ib. 4 in. 3.5 in. 4/4 7 in.
Created from steel and brassgraded Rod, two at each endplaced between the fixed wall, B60kN respectively from and D pointsand 40kn axial forceswere exposed. Accordinglysteel (Eçelik=200GPa andEpirus=105GPa) formed in ricemaximum stressescalculate.
Downvote for incorrect answer The connection is made using a bolt and nut and two washers. If the allowable bearing stress of the washers on the boards is (b)allow 2 ksi, and the allowable tensile stress within the bolt shank S is (allow 18 ksi, determine the maximum = allowable tension in the bolt shank. The bolt shank has a diameter of 0.31 in., and the washers have an outer diameter of 0.75 in. and inner diameter (hole) of 0.50 in.
The vertical shaft with a diameter of d = 20 mm is supported by a thrust collar that rests on a 21-mm-thick plate. The thrust collar is 16-mm thick. Assume that the load P causes a compressive stress of 190 MPa in the shaft. If the bearing stress between the thrust collar and the plate is limited to 35 MPa, determine the minimum outer diameter Dcollar that must be used for the thrust collar. Thrust collar area Plate Thrust collar d Dcollar
A pivoting cantilevered chair support is proposed for an industrial equipment application. If the maximum person weight is 180 lb, determine the greatest distance the chair can extend from the pivoting support at A. The cantilever is made from 1"x3" aluminum tubing with an allowable normal stress of 20 ksi. Also determine to the nearest 1/8" the diameter of the steel pin at A needed for the chair support to pivot about. Use 10 ksi as the allowable shear stress for steel. 180 1 in. 3 in 2.5 in. --0.5 in. 8 in.
The steel bar has the dimensions shown. Determine the maximum axial force P that can be applied so as not to exceed allowable tensile stress of sallow = 150 MPa.
The two steel shafts (1) and (2) each Ø10 should be connected to each other with the help of the sleeve (3) (Øinner = 10, Øoutside = 15) also made of steel and two rivets at the points shown. The shaft (1) is firmly clamped on the left- hand side, the force F = 100 N acts on shaft 2 in the direction of the arrow. How are the brass round rivets to be dimensioned so that a safety of the coupling against failure of S = 10 is achieved? hole for rivets 1 F 3 a) What type of connection does a riveted connection have? b) What type of load does the rivet have? c) What is the diameter of the rivets? d) Which areas of the rivet are loaded? (Draw in figure and formula) e) Dimension the rivet