Answered: Question 2: The circuit below is a… | bartleby

Electric Motor Control

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Related questions

Question

Question 2: The circuit below is a synchronous sequential circuit based on D-type flip-flop (DFF):
X
D1
D
Q1°
Q1
D
D2
Q2
Q2
N
Clk
(a) Write the excitation and state equations for the two DFFs.
(b) Express the output equation for the output z.
(c) Determine the present and next state table and output of the circuit.
(d) By using the result obtained in (c), sketch the circuit using negative-edge triggered JK flip-flops
(JKFFS) and some primitive gates.

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

Write the next-state equations for the flip-flops and the output equation. (b) Construct the transition and output tables. (c) Construct the transition graph. (d) Give a one-sentence description of when the circuit produces an output of 1. Q2 D2 Q1 T1 CLK Figure 4
Q) You want to design a synchronous counter sequential (sequential) logic circuit. Counting from 0 to 9 and will not count the last two digit of your student number. (a) List the steps that you will apply in the design approach. State Chart and State Create the table. (b) Design the sequential circuit using JK Flip-Flop. Explain each step. Desired action show that you have done it. " last two digit student num: 0 4 " Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, I want the solution on paper if possible.
Q) You want to design a synchronous counter sequential (sequential) logic circuit. Counting from 9 to 0 and will not count the last digit of your student number. (a) List the steps that you will apply in the design approach. State Chart and State Create the table. (b) Design the sequential circuit using JK Flip-Flop. Explain each step. Desired action show that you have done it. " last digit student num:4 " Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, I want the solution on paper if possible.
A sequential circuit has two JK flip-flops A and B, two inputs x and y, and one output z. The flip-flop input equations and circuit output equation are attached below: a) Draw the logic diagram of the circuit. b) Derive the state equations for A and B c) Tabulate the state table. d) Draw the state diagram for the circuit and describe the function of circuit.
3.) The design size of the synchronous counter sequential (sequential) logic circuit. It will count from 0 to 9 and the son of your student number will not count decimals in two digits. A. List the process steps that you will apply in the design approach. Create the State Chart and State Chart. B. Design the sequential circuit using JK Flip-Flop. Explain each step. Show that it has performed the desired action. last digit student num: 0 4 " Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, I want the solution on paper if possible.
You want to design a synchronous counter sequential logic circuit. Counting from 0 to 9 will perform and not count the numbers 0, 3, 5, 8. (a) List the steps you will apply in the design approach. State Diagram and Status Create the table. (b) Design the sequential circuit using Flip-Flops. Explain each step. Desired action show that it does.
4- Draw the output waveform if the signal shown in Figure below is applied to inputs of J-K Flip-Flop. Q is initially Low. HIGH CLK- CLR nnnnnnn CLK PR CLR
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
Given the state diagram and D flip-flop, derive the state table, Flip-flop input equation and output equation, and logical diagram.
4-6. A sequential circuit with two D flip-flops A and B and input X and output Yis specified by the following input equations: Y = A + B D = X + B D = XA (a) Draw the logic diagram of the circuit. (b) Derive the state table. (c) Derive the state diagram. (d) Is this a Mealy or a Moore machine?
Q.6 Given a sequential circuit implemented using two JK flip-flop as in Figure Q.6a. Analyse the circuit by completing the timing waveform given in Figure Q.6b. QA QB Vcc SET SET J K CLR Q K CLR CLEAR Clk Figure Q.6a Clk CLEAR QA Qs Figure Q.6b
The following statements describe the sequential circuits. Select all the TRUE statements. a The sequential circuits consist of a combinational circuit and storage elements. b The storage elements keep a binary bit even though the circuit power is gone. c Only the current input determines the outputs of sequential logic circuits. d The flip-flop is controlled by signal levels.

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electric Motor Control

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

SEE MORE TEXTBOOKS