Question #1A block diagram of a system consisting of a sinu-soidal voltage source, an RLC series bandpass fil-ter, and a load is shown in Fig. P14.32. Theinternal impedance of the sinusoidal source is80+10, and the impedance of the load is480 + j0 0.The RLC series bandpass filter has a 20 nFcapacitor, a center frequency of 50 krad/s, and aquality factor of 6.25.a) Draw a circuit diagram of the system.b) Specify the numerical values of L and R for thefilter section of the system.c) What is the quality factor of the interconnectedsystem?d) What is the bandwidth (in hertz) of the inter-connected system?Figure P14.32SourceFilterLoadAnswer #18002L200"R4800SourcefilterL = 20 mH, R = 160 . Q = 5,loadẞ = 1591.55 Hz

Answered: Image /qna-images/answer/5902470e-a452-4318-8683-00bc4707c9ff.jpg

Answered: Question #1 A block diagram of a system…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For a series RLC circuit with a sinusoidal input voltage, the amplitude of the current passing through the circuit (lo in mA) is plotted as a function of frequency for two cases: Curve 1 with R1, L1, and Curve 2 with R2. L2 as shown in the next figure. The value of the capacitor used in the circuits is C=0.01 micro Farads. The quality factor (Q1) for curve 1 is about: 7.5 5- 2.5 1-10 1-10 1-10 1-10 Frequency (f), Hz O a. 20000 Hz O b. 0.5 O c. 0.23 O d. 2 O e. 1.5
An op amp-based low-pass filter with a cutoff frequency of 250 Hz and a passband gain of 4 is shown in Figure. If the capacitor has a capacitance of 20 uF (micro Farad). What are the values of R1 and R2 in Ohms?
A circuit contains a capacitor with C-20.0 uF connected to an AC source operating at an amplitude of 36.0 V and frequency f-60.0 Hz. a) Gives the expression of the voltage across the capacitor vc(t) and the current i(t) in the circuit. b) We want to add a resistor and an inductor is series to the capacitor to make a resonant circuit. Whic values of resistance and inductance should be selected ?
Q.4: Choose the suitable choice for the following sentences. 1. At any resonant circuit the input impedance is ....... a. XL. b. RT. c. XC. 2. The locus of inductive load is a vector in the …... quadrant. a. 4th. b. 2nd. c. 3rd. 3. For non-sinusoidal input signal, the power dissipated in a resistance is equal to ............ a. 2I2R. b. Iav2R. c. Ieff2R. 4. Applying Kirchhoff's laws to RL & RC transient circuits produces Equations of type:a. Time-Depend. b. Time-Variable. c. Differential. 5. The Differential Equations applied RL & RC transient circuits are:a. Third-order b. Second-order c. First-order 6. Electrical energy is stored in ........ a. Inductance. b. Capacitance. c. Both-of-them. 7. .......... is obtained in parallel resonance circuit. a. Vmax. b. Imax. c. Pmax. 8. The total impedance angle is ............ on the frequency of the harmonic.a. Dependent. b. Independent. c. Both-of-them. 9. In transient circuit, the capacitor behaves as ................ when the switch…
Problem Solving: 1. Given a value of Cx = 12pf, C = 40pf, Ca = 8pf, Co = Spf, and C - 8pF Determine: a) Input impedance (Z) b) Low cut-of frequency c) High cut-off frequency d) Av(mid) e) fa and fr f) Sketch the complete frequency response of the circuit 14V 5.6 kn 6R LO 0.47uF 0.82ko B- 120 0.47UF 10 kn 1.2 kn *20
As part of a radio receiver, you are asked to design a simple bandpass filter using a series inductor, capacitor and resistor. The filter needs to pass a centre frequency of f0 = 1089 kHz with a bandwidth of 9 kHz. Do this by finding the capacitor and resistor values together with a 240 uH inductor that will give you the correct centre frequency and bandwidth. Also, calculate the quality factor Q for your filter. Sketch the filter circuit and show all your calculations.
Design a filter using the window method and provides the specifications for the filter design. Here is a summary of the specifications given: Stopband: [0 kHz, 4 kHz] Passband: [5.5 kHz, 16 kHz] Maximum ripple in the passband: 0.1 dB Minimum attenuation in the stopband: 51 dB Sampling frequency: 32 kHz The task is to design a filter (by hand, with the impulse response formula) that meets these specifications.
Ex. 600. A series circuit containing a resitor (6 Ohms), a capacitor (4 Farads), inductor (13 Henries), and a voltage source V. Determine the transfer function I(s)/V(s) and then determine the undamped natural frequency (Wn) and damping ratio (zeta). Answers: Wn, and zeta. ans:2
A parallel R-L-C circuit is fed by a constant current source of variable frequency. The circuit resonates at 100 kHz and the Q-factor measured at this frequency is 5. Find the frequencies at which the amplitude of the voltage across the circuit falls to (a) 70.7% (b) 50% of the resonant frequency amplitude.
I really need help with this question. Please explain this and give me a clear solution. Thanks in advance. In the block diagram below, it depticts a simple phase-shift single-sideband mod-ulator.
A transducer measures a sinusoidal signal with an amplitude of +-5V and a frequency up to 10Hz. Superimposed on this signal is 60-Hz noise with an amplitude of 0.1V. It is desired to attenuate the 60-Hz signal to less than 10% of its value using Butterworth filter. - Select the filter order n and its cutoff frequency fc. Justify your selections - What is the disadvantage of selecting the filter cutoff frequency, fc to equal the highest frequency output of the measured signal?
uvquvurd Q2 A series RLC bandreject filter is used to reject a 200 Hz sinusoid while passing other frequencies, calculate the values of L and C. Take R=150 Q2 and as 100 Hz. the bandwidth

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS