Problem Figure: Steel A=600 mm? E=200 GPa L=2 m In the Figure shown, the rigid beam with negligible mass was horizontal before the load P was applied. Determine the value of load P if the vertical movement at P is 3 mm. Draw the FBD and deformation Aluminum A=900 mm2 E=70 GPa L=1.5 m diagram. 1.5 m <1m 0.5 m

Problem Figure: Steel A=600 mm? E=200 GPa L=2 m In the Figure shown, the rigid beam with negligible mass was horizontal before the load P was applied. Determine the value of load P if the vertical movement at P is 3 mm. Draw the FBD and deformation Aluminum A=900 mm2 E=70 GPa L=1.5 m diagram. 1.5 m <1m 0.5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
A cantilever of length L has a solid circular cross section of diameter D and carries a vertically downward load Wat its free end. The modulus of rigidity of the cantilever is G. Calculate the shear stress distribution across a section of the cantilever and hence determine the deflection due to shear at its free end. Ans. t = 16 W(1–4y²ID²)/3¤D², 40WL/9#GD² (downwards).
Two aluminum (Ea=77 GPa) rods AB and CD, and a steel (Es=202 GPa) rod EF support a 82.7 kN load P. Each of the rods has a 400 mm2 cross- sectional area. Neglecting the deformation of rod BED, determine the change in length (in mm correctly up to two decimal places) of rod AB. A C P 500 mm В E 400 mm F
10. The hoisting beam assembly shown is supported by two 20- mm-diameter bolts at A and a 150 mm x 200 mm plate at B. In this problem, a = 1.2 m and b = 2.8 m. If the allowable tensile stress of the bolts at A is 112 MPa, which of the following gives the maximum safe value of W in KN? A. 45 C. 30 B. 60 D. 15 ZEIT 0 a BEEN H 8804 pe (cAPlate B to tried man 11 of 1911 b bell 110 mb llame lis To 102 W 20-102 bugil noitsuta
イ H.W.pdf -> A simplified model as shown in figure below of a planur robotie urm. You may ussue thut each segment has length 1.5 m, aad the applied force is 250 N. 0, = 35 and -0,- 20. Calculate dhe aoncnt that the force, F. cacits about dhe point A ...
90°–0 9. A A metal [E = 106 GPa; v = 0.31] bar of height h = 40 mm and thickness t = 8 mm is subjected to an axial load P. Two strain gages mounted at point A measure strains of ɛx = 575 µɛ and ɛy = -10 µɛ; however, the angle 0 indicated in the figure is not known. What is the magnitude of load P? Ex + Ɛy' : i με Ex + Ɛy = i Ox = i MPa P = i kN
Q2: Find the permissible distance (X) for the beam shown in figure. If the stresses in tension is 40 MPa and in compresion is 80 MPa. 4kN 4KN. 220 16KN N. A 大 6m 'RB INA: 4 = 20* (o mm
A steel beam is subjected to a uniform load with length of 8m. Assume that the beam is simply supported. Use Fy= 248 Mpa. Properties of W-shape beam d=229 mm bf=210 mm rf=23.7 mm Tu-14.50 mm kdes=33. 80mm ry=53.80 mm Ix=113 x 10^6 mm^4 Iy-36.9 x 10^6 mm^4 Sx-990 x 10^3 mm^3 Zx 1150 x 10^3 mm^3 J-2100 x 10^3 mm^4 Cu-387 x 10^9 mm^6 What is the nominal shear strength capacity of the section (in kN)?
Determine the maximum tensile stress and maximum compressive stress due to the load P acting on the simple beam AB (see figure). Data are as follows: P= 5.4 kN L=3.0 m d=1.2 m b=75 mm t_=25 mm h=100 mm h1=75 mm c1=62.5 mm c2=37.5 mm, and l= 3.3203x10⁶ mm⁴
A portal frame shown in figure (not drawn to scale) has a hinge support at joint P and a roller support at joint R. A point load of 50 kN is acting at joint R in the horizontal direction. The flexural rigidity. El, of each member is 106 kNm². Under the applied load, the horizontal displacement (in mm, round off to 1 decimal place) of joint R would be Q P FIAT 5 m EI pole El 10 m R 50 kN
SITUATION III: The cross section of a tension member is shown below: Use Fy=275 MPa, Fu=400 MPa. 25 350 16 mm o 30 25 350 12. Compute for the gross area of the cross section. b. 29750 mm² d. 23000 mm? a. 28 000 mm? C. 23 490 mm? 13. Compute for the allowable tensile capacity due to yielding. a. 4698.00 kN C. 4610.78 kN b. 4654.39 kN d. 6706.59 kN 14. Compute for effective net area if shear lag factor is 0.90. Diameter of holes is 3mm more than that of bolts. a. 28 000 mm? C. 23 490 mm² b. 29750 mm? d. 23000 mm?
Given the image below what is the equivalent force-bouple at poitn A at tension of cord Cg when Tcg = 52.1N?