Two uniformly distributed loads of w = 4200 lb/ft act on the simply supported beam shown in Figure A. The beam spans are a = 8.8 ft and L = 17.2 ft. The beam cross section shown in Figure B has dimensions of b = 18.00 in... di = 6.75 in., b₂ = 11.00 in.. and d2 = 10.25 in. Calculate the maximum tensile and compressive bending stresses produced in segment BC of the beam. W a FIGURE A tensile FIGURE B compressive L by 1 5020.66 1 3935.4 W a psi Psi D

Two uniformly distributed loads of w = 4200 lb/ft act on the simply supported beam shown in Figure A. The beam spans are a = 8.8 ft and L = 17.2 ft. The beam cross section shown in Figure B has dimensions of b = 18.00 in... di = 6.75 in., b₂ = 11.00 in.. and d2 = 10.25 in. Calculate the maximum tensile and compressive bending stresses produced in segment BC of the beam. W a FIGURE A tensile FIGURE B compressive L by 1 5020.66 1 3935.4 W a psi Psi D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Compute for the maximum allowable distributed load o that can be applied to the simply supported beam as shown in Figure M-Va. The beam's cross section is detailed in Figure M-Vb. @(N/m) Allowable Stresses: Fiber Stress = +13.5 MPa / -12 MPa Transverse Shear Stress at NA = 900 kPa Transverse Shear Stress at Junction 800 2 m Figure M-Va 2 m Draw the flexural and shear stress distributions of the cross section. T 40 40 40 Figure M-Vb 40 120 mm
Determine the maximum tensile and compressive stress in the beam. 1600 lb 4000 lb 7 in N.A. 2 in 3 ft T R1 6 ft 6 ft R2 Ina = 84 in
A 16 mm steel bar AB and a 25 mm steel bar BC support a load P = 7,500 N as shown. If E = 200 GPa, Compute the deformations of the steel bars. A B 7,500 N 6.00m C 8.00m
The rigid plate ABC shown in figure 2, was positioned on top of two identical steel posts, and the aluminum post was 0.1mm shorter than the steel posts at temperature of 50°C, if the allowable compressive stress in steel is limited to 120 MPa and in aluminum to 150 MPa, what is the maximum possible load P that can be supported on the rigid plate at temperature of 10°C ? A steel ryid steel st I ビ= 200 G。 50°d -Aluminum %3D L= 250MM A : = 1600 mu? X = 12 x10%2 Tell = 200 MPa Comp %3D Aluminumr Post. E = 73 GPa A 400 mal 40omm 2 = 2400 mm K = 23x10/ Figure 2 = 150 MPa all Comp
P = 9 kip 2 in. 1 in. 1.5 ft The aluminum post shown in the figure is reinforced with a brass core. If this assembly supports an axial compressive load of P = 9 kips applied to the rigid cap, determine the average normal stress in the aluminum and the brass. Take Eal=10103ksi and Ebr= 15103ksi.
6.59 A square section as shown in the figure below is subjected to bending moment M. (c) Obc = Obl y || h y H What is the maximum bending stress? (a) Obc = obt 12M h³ 9M 2h³ JXC h (b) bc = Obt = (d) %bc =%bt = 6M 4³ 9M h³
A small aluminum alloy [E = 74 GPa) tee shape is used as a simply supported beam as shown. For this beam, o = 130 mm. The cross- sectional dimensions of the tee shape are b= 23 mm, d = 35 mm, and t = 8 mm. After loads are applied to the beam at B,C.and D, a compressive normal strain of 480 ue is measured from a strain gage located at c = 7 mm below the topmost edge of the tee stem at section 1-1 What is the applied load P? 3P Strain gage D H Answer: P= N
2. Two rods connected as shown carry a vertical load of 20 kN. Rod AB is a steel rod with E = 2 X10 MPa while rod BC is made up of aluminum whose E = 7x10¹MPa. The rods are rigidly pinned at A and C and have cross-sectional areas equal to 400 mm². If a is changed from 30° to 45°, compute: (a) stresses in each rod. Specify if tensile or compressive stress (b) deformation of each rod. Specify if elongation or shortening. B P=20 KN L=3m α=30° 70=30° L=2m
A small aluminum alloy [E = 71 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 120 mm. The cross- sectional dimensions of the tee shape are b = 17 mm, d = 26 mm, andt = 6 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 µɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P P ЗР Strain gage C |D H Answer: P = N
For the cantilever beam shown. find the value of Normal stress due to axial load at :point F FO ce A 10 m Diameter 100 mm 6 KN.m No stresses at point D 0 -31.229 Mpa +40.99 Mpa -0.25 Mpa +40.49 Mpa No stresses at point F No stresses at point A No stresses at point B +0.25 Mpa +40.74 Mpa No stresses at point C -40.99 Mpa +31.229 Mpa -40.74 Mpa +30.55 Mpa -40.49 Mpa +0.679 Mpa -0.679 Mpa No stresses at point E -30.55 Mpa
A small aluminum alloy [E = 62 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 155 mm. The cross- sectional dimensions of the tee shape are b = 16 mm, d = 24 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 470 µɛ is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P Strain gage х B 11 D E a a H b sla
The beam seciton shown below has moment of inertia about its neutral axis: I = 301.3 (10 -6)m 4 , and if this section is under a bending moment of 22 kN m, please calculate the normal stress at Point B: ____ MPa. Calculate your answer to 1 decimal place.