In a superheterodyne receiver, the incoming RF signal is at 25 dBµ. the RF amplifier has a 30 dB gain, the mixer has a 10 dB loss, the IF amplifier has 20 dB gain and the demodulator has a 5dB loss. What is the AF level at the output of the demodulator? (Assume that noise in each block is negligible) a.90 dBµ b.40 dBµ c.30 dBm d.60 dBm

In a superheterodyne receiver, the incoming RF signal is at 25 dBµ. the RF amplifier has a 30 dB gain, the mixer has a 10 dB loss, the IF amplifier has 20 dB gain and the demodulator has a 5dB loss. What is the AF level at the output of the demodulator? (Assume that noise in each block is negligible) a.90 dBµ b.40 dBµ c.30 dBm d.60 dBm

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

12- A DVM measure... a- peak value. b- RMS value. Average value. d- peak to peak value. 13 The study of energy distribution across the frequency spectrum of a given electrical signal is done by a Distortion meter b-wave analyzer.
Find the resonance point and the half-width of the speed versus frequency curve for the damped harmonic oscillator, under the action of a sinusoidal driving force. *It is all the data
1-Ideal Envelop Detector 2-AM demodulation using diode and RLC circuit 3-Demodulation of AM signal using envelop detector Question 8: Can an overmodulated AM signal be recovered with the above demodulators? If possible, explain how.
One input to a conventional AM modulator is a 600 kHz carrier with amplitude of 22 V. The second input is a 20 kHz modulating signal that is of sufficient amplitude to cause a change in the output wave of +9 V. Determine: a. Upper and lower side frequencies. b. Percent modulation. c. Peak amplitude of the modulated carrier and the upper and lower side frequency voltages. d. Maximum and minimum amplitudes of the envelope. e. Expression for the modulated wave. Then, f. Draw the output spectrum. g. Sketch the output envelope.
drive a formula for (SNR) of sinusoidal signal has been sampled and quantized.
a) Consider the system shown in Figure 3(a). An input signal vm(t) is multiplied by a complex exponential signal e10nt The output signal v,(t) is fed into a low pass filter (LPF) with cut-off frequency wc. The input signal Vm(@) and the output signal V.(@) are as shown in Figure 3(b) and (c), respectively. i. Write the mathematical equation for signal in Figure 3(b). ii. Sketch signal, V,(@). iii. Based on the given V, (w), write the mathematical expression of the LPF, H(@) and state its cut off frequency, wc. iv. Sketch the output of LPF, V(@), if the cut off frequency of LPF is 10. v:(t) LPF Vm(t) vo(t) H(@) ej10nt (а) |Vm (@)| IV,(@)| 10 8 6. 3 -20715T-10T-5n 5n 10n 15n 20n -57 (b) Figure 3
A channel having a bandwidth of 1 kHz, the power of signal is 10 W and the power of noise is 5 W. Determine the channel capacity. Or: A channel having a bandwidth of 1 kHz and Signal to Noise Ratio (SNR) is 2. Determine the channel capacity.
If a positive change in modulation signal level of 200 mV will cause a positive frequency deviation of 10 kHz, what I be the frequency deviation for a negative change of 100 mV in the level of the modulating signals? (Ans:-5kHz)
b) Draw the block diagram of the phase - locked loop (PLL) that can be used to demodulate FM signals. Explain briefly . the operation of this demodulator
1. Attenuator of -10dB has gain () 2. An output signal has a fundamental amplitude of 2.5V, second harmonic amplitude of 0.25V, and third harmonic amplitude of 0.1V. then the total harmonic distortion is found to be 3. The current capability of power diodes can be increased by placing two or more in 4. As the illumination on a photoconductive cell (photoresistive device) increases in intensity, the terminal resistance will 5. The LCD has the advantage of having than LED. 6. The triac is fundamentally a diac with a for controlling the turn-on condition. prevo t hat lt
- at A signal Flt) = 2e ult) is applied to the input of.. System have frequency trunsfer funchiom THlw)I = Determine the required relations ibetween the Constants a und b Such that exactly 50% of the input energy on to the output %3D a 1-ohm basis is transffered
QUESTION 2 a. In a full wave rectification, average DC current, RMS value of Current, DC power output and AC power input are very important parameters. Derive the expressions for them. b. Explain why the BC junction of an NPN transistor is reversed biased? c. Draw the circuit of inductor filter and explain its operation.