For laminar flow over a flat plate, the local heat transfer coefficient hx = x-1/2 where x is thedistance from the leading edge (x=0) of the plate. What is the average heat transfer coefficient hxfrom the leading edge to location x.

Answered: Image /qna-images/answer/0a6ffb91-02a0-4ca5-ad8d-1ba740478e26.jpg

Answered: For laminar flow over a flat plate, the…

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.20P

See similar textbooks

Similar questions

-1/5 A// For laminar flow over a flat plate, the local heat transfer coefficient h, is known to vary as x¹/5, where x is the distance from the leading edge (x =0) of the plate. What is the ratio of the average coefficient between the leading edge and some location x on the plate to the local coefficient at x? for velocity equation u= 2-0.43x+x² Plot the local heat transfer coefficient over a 0.8 cm length(take T-35c) B// Air at 1 atm and 15°C flows through a long rectangular duct 7.5 cm by 15 cm. A 1.8-m section of the duct is maintained at 120°C, and the average air temperature at exit from this section is 65°C. Calculate the airflow rate and the total heat transfer
Topic: Heat transfer Completely solve and box the final answer. A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? If the average laminar heat transfer coefficient of water is 7740W/m2 degC, what is the overall heat transfer at the laminar section?
Topic: Heat transfer Completely solve and box the final answer. 1. A 20degC water flows to 50cmx60cm flat plate with velocity of 5.2m/s . The flat plate surface temperature is maintained at 40deg C. The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent?
BTU hr.ft. FA A hollow sphere (r = 6 in, r = 2.5 in) shaped food particle (k = 45; is heated. in microwave oven and the oven provides a heat generation (Q = 0.5 × 105 BTU) in the overall volume of the material. What is the temperature profile along the sphere and the temperature at r = 5 in if the surface temperature is 120 °F? (Answer: 161.15°F)
A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? If the average laminar heat transfer coefficient of water is 7740W/m2 degC, what is the overall heat transfer at the laminar section?
Describe the process of internal flow convection heat transfer in an annular tubeconcentric and draw
HEAT TRANSFER From the heat transfer property table of water, the properties at 20 0C are as follows: Density = 997.36 kg/m3 Kinematic viscosity = 1.026 × 10-6 m2/s Prandtl number = 7.17 (i) Thickness of hydrodynamic boundary layer = 9.24 mm (ii) Thickness of thermal boundary layer = 4.79 mm (iii)Local friction coefficient = 0.001228 Average friction coefficient = 0.002456 ANSWER QUESTION (iv) ,(vi) and B
A nuclear reactor is cooled by liquid sodium. The liquid sodium has the following properties: dynamic viscosity = 0.41 mPa·s, specific heat capacity = 1.2 kJ/kgK, thermal conductivity 82 W/mK. Which of the following statements is correct for this scenario? please explain A The thermal boundary layer is thicker than the hydraulic boundary layer. B Heat is transferred through the fluid more easily than momentum. C The velocity varies significantly from the surface to the thickness of the thermal boundary layer. D The hydraulic boundary layer is thicker than the thermal boundary layer.
Explain the physical significance of the Nusselt. Calculate the Nusselt numbers for the following: A gas flow (Prandtl number, Pr = 0.71, dynamic viscosity, μ = 4.63 x 10-5. and kg ms specific heat, Cp = 1.175 kJ/kgK) over a turbine blade of chord length 20 mm, where the average heat transfer coefficient is 1000 W/m².K.
Air at 10 m/s is flowing over a cylinder of D=(1) cm and L = 1 m. Air has thermalconductivity 0.027 W/mK, kinematic viscosity 1.9*10-5 m2/s, and Prandtl number 0.72.Find the Nusselt number uses charts/table also if needed
Air at 20 C is flowing over a flat plate ( 6m long and 1.5m wide). The plate is maintained at 140 C. Find the heat loss from the plate if the air is flowing parallel to 6m side with a velocity of 2 m/s. What is the percentage change in heat transfer if the air flow is parallel to 1.5m side. The properties of air are: p=1.06 kg/m v 2.548x10 m/s, k=0.0295 W/mK and Pr-0.7. Nu =0.664Res Pr1 for laminar flow Nu, = (0.037RE-871)Pr for turbulent flow
Q2) In flow over a surface, velocity and temperature profiles are of the forms u(y) = Ay + By² + Cy3 and T(y) = D+ Ey + Fy? - Gy3 where the coefficients A through G are constants. Obtain expressions for the friction coefficient C, and the convection coefficient h in terms of uo, To, and appropriate profile coefficients and fluid properties. Q3) Water at a temperature of T = 25°C flows over one of the surfaces of a steel wall (AISI 1010) whose temperature is Ts1 = 40°C. The wall is 0.35 m thick, and its other surface temperature is Ts,2 = 100°C. For steady state conditions what is the convection coefficient associated with the water flow? What is the temperature gradient in the wall and in the water that is in contact with the wall? Sketch the temperature distribution in the wall and in the adjoining water.

SEE MORE QUESTIONS

Recommended textbooks for you

Principles of Heat Transfer (Activate Learning wi…

Mechanical Engineering

ISBN:

9781305387102

Author:

Kreith, Frank; Manglik, Raj M.

Publisher:

Cengage Learning