Determine ¯Ix for the triangular region shown. (Ans: 1.689 × 105 mm4)

Q: As per IS 800, the efficiency of a riveted joint having the minimum pitch is: 1. 60%

A: Problem from steel structure, Where we are asked to determine the efficiency of a riveted joint…

Q: The frame shown in Figure is supported by a hinge at E and a roller at D. Compute the horizontal and…

A: Given data,  Load = 24 kN Angle = 45°

Q: A steel specimen of 12 mm diameter extends by 6.31 x 10-2 mm over a gauge length of 150 mm when…

A:

Q: An object weighing 100 N in the air was found to weight 75 N when fully submerged in water. The…

A: Given data- Weight of the object W=100 N, Weight in water =75 N, To Find- The relative density RD of…

Q: Determine whether the plate is ill-arranged, geometrically unstable, statically determinate,…

A:

Q: The following data were obtained by conducting liquid limit and plastic li tests on a soil collected…

A: To determine: a) Draw the flow curve and determine the liquid limit b) Using the Casagrande…

Q: 6200 N 4.5 m 2 m 1.5 m 4.5 m E b.) Determine the forces in members AB, BD and DE by the Method of…

A:

Q: A rigid 2m square footing is constructed over a loose sand layer as shown on the figure. It carries…

A:

Q: An annual flood series contains 100 years of flood data. For a return period of 200 years the…

A:

Q: For the diagram shown below find the reactions at each support

A: Given Data  Find the support reaction

Q: If the Greenwich civil time is 20hr30m15s P.M on june 13, 2019. Find the LMT for place 120degreeW

A:

Q: 3. By using the left side of the figure. determine the force in members FH, FG, and EG by using…

A:

Q: 2. When making a batch of Miralium Danielide gears using conventional processes, the porosity is…

A: Given,porosity=10%porosity should decrease to 7%n=3.75To determine,How much does the system improve…

Q: Problem 3 The following are the observed bearings of a close traverse. Compute the error of interior…

A:

Q: Determine the force in member AB for the truss using the method of joints. T 2.5 m TT 20 KN O a. 52…

A: Given data,  Load at B = 40 kN Load at C = 40 kN Load at A = 20 KN

Q: A solid plastic rod has a diameter of d = 18 mm and a length of L = 525 mm. An axial load of P = 25…

A:

Q: An annual flood series contains 100 years of flood data. For a return period of 200 years the…

A: Given data: An annual flood series contains 100 years of flood data. Return period, T = 200 years.

Q: If the distance between E and Bis h= 0.3 m, calculate the maximum absolute values of the shear and…

A: Given Data  Find maximum absolute shear force and bending moment.

Q: Determine the location of the shear center O of a thin-walled beam of uniform thickness having the…

A:

Q: 8.15) The flow rate and water depth just upstream of a dam are 15 m³/s and 4.0 m respectively. The…

A: Reference : Fluid mechanics, Rectangular Channel section. Given : Flow rate, water depth, width ,…

Q: Determine the horizontal and vertical components of force at pins A and C of the two member frame.

A: Given data : Problem of Structure, where we are asked to determine the horizontal and vertical…

Q: Compute

A:

Q: Problem 2 Fill up the missing data Draw the traverse. LINE AB BC CD DE EF DISTANCE(m) 42 35 80 80 45…

A: Given: Length of AB=42 m Length of BC=35 m Length of CD=80 m Length of DE=80 m Length of EF=45 m…

Q: A quadrilateral ABCD (violet) is subjected to axial and shear forces transforming it into a right…

A: The given figure is shown below:

Q: A 3 kN/m -6m-

A:

Q: na pond at a depth of 5m air bubble m. Calculate gauge pressure inside air bu on = 0.075N/m.

A:

Q: Determine the force in members marked with "x" of the truss shown by the method of sections or…

A:

Q: Write the V and M equation of the beams loaded as shown and the diagram. Then repeat the method…

A: Given,

Q: The jib crane is designed for a maximum capacity of 15 kN, and its uniform I-beam has a mass of 220…

A: Given,  R =  160.6x2- 93.526x + 255.46 Operating range x = 0.2 to 3.7m

Q: Solve the problem with complete and neat solution. Draw the figure. Situation1. Determine the…

A:

Q: Q.21. In the PCA design procedure of rigid highway pavements, as the stress ratio (applied flexural…

A: "Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: A leaf spring of semi-elliptical type has 11 plates each 9 cm wide and 1.5 cm thick. The length of…

A:

Q: Determine the drawdown at a distance of 50 m from a well pumping constantly at 50 US gpm after one…

A:

Q: Only answer A. Explain why the obtained answer makes sense.

A: This question is related to the Strength of the material from Civil Engineering. As per question…

Q: (iv) Determine the force in member BC of the truss shown below. Is the member BC in tension or…

A: Given data in question  Load 94.5 N Dimensions  Truss  To find out  Force in member BC

Q: Determine the reaction at A for the beam shown below. 3m O a. Ay = 246 kN ↓ O b. Ay = 148 kN ↓ O c.…

A:

Q: Calculate the shape factor and fully plastic moment Mp of the section shown in above figure . Assume…

A:

Q: () If Lb=4' (2) If Lb= 10' (3) If Lb= 15 (4) Vn=?. & Mn = ? & Mn = ? & Mn = ?

A: Answer  From AISC Table 3-2 we can draw ϕ.Mp = 574 kip-ft ϕ.Mr = 344 kip-ft Lp = 4.87 ft Lr = 14.4…

Q: Why do we occasionally need to reduce project duration? And how?

A: Project Duration: Project duration is the time mentioned for the completion of the project. Project…

Q: The section of a gate at the end of a tank is shown below. The length of the gate is 3 m normal to…

A: The unit weight of water, γw = 9.8 kN/m3 Parabolic gate, y2 = 5x The length of the gate, L = 3 m The…

Q: 4. A linear coastal aquifer has a mean hydraulic conductivity of 50 meters per day. The density of…

A: The given data is shown below: Mean hydraulic conductivity=50m/dDensity of fresh water=1g/cm3Density…

Q: Determine the vertical reaction at B for the beam shown below.

A: Answer  Draw free body diagram replacing the supports with reaction forces 33 is centroid of left…

Q: In the figure below, one end of a uniform beam of weight 943 N is hinged to a wall; the other end is…

A:

Q: The AASHTO present serviceability index (PSI) correlates the PSR to actual pavement performance in…

A: The original AASHO Road Test PSR serves as the foundation for the current serviceability index…

Q: MODULAR 01 - STRUCTURAL THEORY ANALYSIS OF STRUCTURES PART 2. Determine the reactions at supports.…

A: Static Indeterminacy= m+r-2j = 7+3-2*5 = 0 Determinate structure, hence can be solved by equilibrium…

Q: The angle of intersection equal to 172, what is the chord distance of the curve (in meters) if the…

A:

Q: Theory of structure Drow A.F.D S.F.D B.M.D

A: Given:

Q: In order to determine the elevation of top Q of a signal on a hill, observations were made from two…

A:

Q: A liquid compressed in a cylinder has a volume of 1000 cm³ at 2MN/m² and a volume of 993 cm³3 at 3.3…

A: Given- Volume V=1000 cm3 @ 2MN/m2, Volume V=993 cm3 @ 3.3 MN/m2,

Q: Determine the moment at A for the beam shown below.

A: ∑MA=0MA-30×4×42-12×30×2×4+13×2-70×6+150=0MA=650 kN.m  ⭯

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.