In the figure below, one end of a uniform beam of weight 943 N is hinged to a wall; the other end is supported by a wire that makes angles - beam. Find the magnitude of the resistive force R acting on the hinge. Hint. If you find this difficult, why not try rotating the figure counter clockwise by 90° ?( keep in mind of the weight). Also, the key in answering this problem is the choice of the perpendicular lever arms for each forces acting. A Hinge NOTES: Final answer in "zero" decimal places. If pi is used: Use pi on your calculator, DO NOT USE pi= 3.14. SI unit of the final answer is not required.

In the figure below, one end of a uniform beam of weight 943 N is hinged to a wall; the other end is supported by a wire that makes angles - beam. Find the magnitude of the resistive force R acting on the hinge. Hint. If you find this difficult, why not try rotating the figure counter clockwise by 90° ?( keep in mind of the weight). Also, the key in answering this problem is the choice of the perpendicular lever arms for each forces acting. A Hinge NOTES: Final answer in "zero" decimal places. If pi is used: Use pi on your calculator, DO NOT USE pi= 3.14. SI unit of the final answer is not required.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the figure, one end of a uniform beam of weight 270 N is hinged to a wall; the other end is supported by a v 27° with both wall and beam. Find (a) the tension in the wire and the (b) horizontal and (c) vertical componen on the beam. Hinge (a) Number i Units (b) Number i Units (c) Number i Units >
The resultant of a force system on a bracket as shown in Figure is acting vertically upwards. If the angle 30° between the two 4 KN forces is fixed. Find the magnitude of the resultant in N.
Current Attempt in Progress The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 390 mm tw = 16 mm d = 100 mm t = 9.6 mm Additionally: • The area of each pipe is A = 2726 mm². • The moment of inertia of the entire beam cross section about the z centroidal axis is Iz=245460000 mm4. If the beam will be subjected to a shear force of V = 275 kN, determine the shear stress at point K, located at yk = 70 mm below the z centroidal axis. H K X Z Ун Ук H ↑ K 31 h
The figure shown is the cross section of an endspan of a fully restrained beam that carries a moment of 200 kN-m. Determine the following: a. The centroid of the cross-section b. The moment of inertia of the cross-section. С. The bending stress on the extreme tension fiber. d. The compressive force due to bending. Check your answer using the force and moment checks. e. 100 mm, 90 mm 250 mm 100 mm, 90 mm 200 mm 110 mm 100 mm 100 mm 80 mm 70 mm 150 mm 260 mm 100 mm 150 mm 60 mm 50 mm 100 mm 100 mm 70 mm 80 mm
Pictured below is a smooth bar (no friction) held in position by a pin and contact with the wall on the left end and subjected to a vertical load P at the right end. Find the distance d that the force needs to be along the bar for equilibrium given the pin is a distance a away from the wall and the bar makes an angle 0 with the horizontal. The weight of the bar is negligible. (Hint: Use the three equations of equilibrium and solve for d. The values for a, 0, and Pare constants.)
A beam is loaded as shown in the Figure. a. Find the resultant Load. b. Find the location of the resultant load from the left support. c. Find the reaction at the left support?
de nangee shape) vwith a spadn of 6 kips/ft. Example 2 The deformation of a simply supported beam, shown in the accompanying figure, is governed by the relationship 7 dy E I. M(x) dr Where M(X) is is the internal bending moment M(x) = M, for all values of x in this problem M, M. O0000KOKO →X а) Derive the equation for the exact deflection. Assume an approximate deflection solution of the form TEX y (x) =A·sin where A = Unknown Coefficient L Use Galerkin Method to evaluate A b) 8
For the beam shown in the figure below, determine the reaction at point C using the singularity functions. Also, determine the most economical W-shape for the beam if the maximum allowable deflection at B is 6 mm (refer to the properties of the rolled-steel - W shape provided). The beam's modulus of elasticity is 200 GPa. The distance 'a' is 3 metre, distance 'b' is 2.5 metre, and the distance 'c' is 3.5 metre. The distributed load, w, is 30 N/m. The load, P is 200 N. P W H A C B W-shape cross-section a b
The T-beam given in the figure is made of two 250 mm x 25 mm section wooden planks. Wooden planks in the figurenailed together as shown A )Draw the shear and moment diagrams (influence lines) of the beam. The greatest shear and bending force acting on the beamDetermine the values of the moment and where it occurs. B)If safe axial stress security σ = 10 MPa and safe shear stress τ at the beam = 0.7 MPa, find whether this beam is safe under the loading shown. c) If the force that each nail can carry safely while fixing the planks to each other is 400 N,Find the longest possible distance.
You and your friends are playing in the lab and shooting a jet of water at a curved plate and watching the water deflect 180 degrees and soak the person beside you. The figure is a top view and the plate curves horizontally, not vertically. For this to work, there needs to be a resisting force, F, that holds the curved plate in place. What is this force (F, kN) given the following? NOTE the following as Forces have directions! Positive x and y axes conventions are provided. Ensure that your F value is given relative to this convention. You can ignore friction. The water jet has a diameter d = 81mm. Vin = Vout = 23m/s. Vin F d Vout ty F
A steel wire 16m long with a radius of 3.6mm is observed to stretch 62mm whena tensile force is applied. Determine the magnitude of the force knowing that E=200 GPa. Answer in kN
A beam is composed of a plate with two longitudinal holes welded on a wide flange profile, as shown in the figure at right. Calculate the moments of inertia Iz and Iy (note y and z axes shown on figure).