Answer all questions below: 1. Draw the general block diagram of Frequency Division Multiplexing (FDM) 2. Multiplexing is a technique that allows the (simultaneous) transmission of multiple signals across a single data link. Figure Q2 below shows a multiplexer with four 500 kbps data stream inputs and 1 data stream output where the unit of data is 1 bit. Determine: i. ii. iii. 500 kbps The type of multiplexing technique used. The input bit duration. The output bit rate. ... 500 kbps 500 kbps. 500 kbps- ... 1 1 0 0 1 0 0 0 1 000 1 1 0 1 1 0 0 MUX Figure Q2 Frames 0101 0001 1101 00010101

Answer all questions below: 1. Draw the general block diagram of Frequency Division Multiplexing (FDM) 2. Multiplexing is a technique that allows the (simultaneous) transmission of multiple signals across a single data link. Figure Q2 below shows a multiplexer with four 500 kbps data stream inputs and 1 data stream output where the unit of data is 1 bit. Determine: i. ii. iii. 500 kbps The type of multiplexing technique used. The input bit duration. The output bit rate. ... 500 kbps 500 kbps. 500 kbps- ... 1 1 0 0 1 0 0 0 1 000 1 1 0 1 1 0 0 MUX Figure Q2 Frames 0101 0001 1101 00010101

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter17: Commercial And Industrial Air-conditioning Control Systems

Section: Chapter Questions

Problem 25RQ

See similar textbooks

Similar questions

1. With the help of Octave program perform the Modulation and Demodulation (AM) of information signal with carrier signal, through subplots with following signals a. Modulating signal b. Modulated signal c. Demodulated signal
Choose the correct answer low HDOP (Horizontal Dilution of Precision) number such as2 indicates a ........................... a.poor fix b.good fix c.poor signal quality d. good signal quality
3. What is the type of demodulation we used to demodulate SSB signal (part-A). Explain your answer.
A 450 kHz carrier signal is modulated with a 15 kHz modulating signal. What are its sideband frequencies?
Which of the following is not an effect caused by multipath in radio channel? a) Rapid changes in signal strength b) Random frequency modulation c) Power of base station d) Time dispersion
• The input to the Encoder is (1), _lines and the output is (2) _lines. • The input to the Decoder is (3). input lines and (4)_ output lines. The multiplexer has (5), output and (6). _inputs.
3. Which of the following is a key characteristic of orthogonal frequency-division multiplexing?A. Amplitude modulationB. Noise performanceC. Digital modulationD. Spectral efficiency
3. Define: a) The circuit that causes one signal to modulate another, and give the names of the two signals applied to this circuit. b) What is the name given to the new signals generated by the modulation process.
We want to design a digital circuit that converts Gray code (ABC) to Binary code (xyz). Set up a 8-to- 1 line multiplexer so that the output gives y as a function of ABC. "A" is given to the most significant bit of the control inputs of the multiplexer. "C" is given to the least significant bit of the control inputs of the multiplexer.
3. Some GPS receivers use 1 bit ADCS (Analog-to-digital Converters) to sample and quantize the signal i.e. the output of the ADC is simply 2 quantization levels: -1 or +1. This is typically done to save on power. (a) What is the quantization SNR? How does it compare to typical thermal noise SNR of a GPS signal before correlating with the CDMA code? (b) Justify, how come it is possible to sample the signal using a single bit and still get good performance.
2. Digital signal is also compatible with multiplexing in what type? A. TDM B. FDM C. WDM D. All of the above
a-Design a full-adder (1)using a multiplexer (2) using a decoder.