3. Some GPS receivers use 1 bit ADCs (Analog-to-digital Converters) to sample and quantize the signal i.e. the output of the ADC is simply 2 quantization levels: -1 or +1. This is typically done to save on power. (a) What is the quantization SNR? How does it compare to typical thermal noise SNR of a GPS signal before correlating with the CDMA code? (b) Justify, how come it is possible to sample the signal using a single bit and still get good performance.

3. Some GPS receivers use 1 bit ADCs (Analog-to-digital Converters) to sample and quantize the signal i.e. the output of the ADC is simply 2 quantization levels: -1 or +1. This is typically done to save on power. (a) What is the quantization SNR? How does it compare to typical thermal noise SNR of a GPS signal before correlating with the CDMA code? (b) Justify, how come it is possible to sample the signal using a single bit and still get good performance.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is the purpose of low pass filtering a PWM source? To minimise noise produced by the PWM pulses To improve PWM efficiency To increase the amplitude of the PWM signal To rectify the PWM signal
Solve using the PCM (Pulse Code Modulation) for the 2-BIT FLASH ADC Circuit Show the steps for Sampling, Quantizing, Encoding. Illustrate the Analog Waveform for Sampling and Quantizing Problem: An oscilloscope's output is an analog signal that ranges only from 12.5mV to 50mV, while its highest frequency is 50kHz. (Vref 50mV, Vin 15mV, 1kohms Resistors). Goal: Convert the oscilloscope's output analog signal into a 2-bit digital signal using a Flash ADC.
Pulse-code modulation (PCM) is the standard form of digital audio in computers, compact discs, digital telephony and other digital audio applications. Figure 3 shows the 3bit PCM system that transmit the 250 kHz analog signal with the voltage range from -6 mV to 6 mV. i) Identify the quantized value, voltage range and binary code for each level by building your own quantization table. ii) Calculate the minimum sampling rate and sampling time. ii) Identify the corresponding sampled voltage, the quantized voltage and binary code if the input signal is sampled at time t1 = 2us, t2 = 4us, t3 = 6us, t4 = 8µs. iv) Sketch the output in (iii) if it is fed to Manchester coding line encoder with bit rate of 20000 bit/sec and amplitude of +4 V. 5 4 3 2 10 Timel(usec) Figure 3 Amplitude (mV)
One control signal selects ZEXT(IR[7:0]) in the MARMUX. Which of the following instructions would use this control signal? JSR/JSRR O NOT O ST, STI, & STR O LD, LDI, & LDR TRAP O BR & JMP
A PM signal has a maximum allowed deviation of 17 kHz, and an actual deviation of 8 kHz. What is thepercentage modulation?
M[Q6] What are the two main advantages of pulse modulation over continuous wave modulation? M[Q7] Explain the aliasing in the sampling and how it can be avoided.
6) In digital frequency meter, Schmitt trigger converts input signal into a ............ wave, which has a fast rise and fall time.
A major advantage of PRTs is that they are very linear. A disadvantage is that they have poor sensitivity. True or false?
Depanment of Electronics Engineering IX. A carrier signal is amplitude modulated by a sinewave. The resulting AM waveform Is shown below. zed 6V 2.5V a) What is the percentage of modulation? b) What is the amplitude of the carrier signal? c) To achieve 75 percent modulation, what amplitude of the modulating signal is needed? d) Calculate the effective voltage of the AM signal SSA AILE Q + Page 4 I 5 X. The frequency spectrum of an AM signal is shown betow: (9 pts)
How to calculate the efficiency in frequency modulation and what is the highest value for efficiency in frequency modulation
Design an encoding matrix with diodes and resistors to display a decimal number to on the seven-segment display. You have 10 switches (WO-W9) with one terminal connected to Vec. For decimal number 0, switch 0 (S0) is closed, for decimal number 1, switch 1 (S1) is closed etc. (Switches are on the vertical axis, S0 on top and the outputs are taken on the horizontal axis (Y0-Y6), with “a" on the left and "g" on the right. Note that (Y0-Y6) outputs are used as inputs to seven-segment display. Since these outputs cannot drive the seven segment display LEDS you may need additional bipolar transistors and resistors. The supply voltage is 5V and each LED needs a current of 20mA. Note that this is a design problem and the design is not unique. Do your best! f a a e
A voice message of 2 kHz is sampled at DM system for a rate nine times the Nyquest rate. The maximum signal amplitude is unity to avoid slop over load. Assuming the input signal amplitude is uniformly distributed in the range .of (-1,1) determine SNR SNR=148.1 SNR=190.2 SNR=180.3 SNR=140.5 SNR=160.4 SNR=160.5 SNR=150.9