Air is flowing through a 20 m long pipe of 20 cm diameter at a rate of 0.8 kg/s. The inlet air temperature is 40 deg C; the entire pipe wall is held at a constant temperature of 90 deg C. Estimate the air temperature at the outlet as well as the heat transfer rate for the entire length of the pipe. Properties are: 1.038 kg/m3; 1009 J/(kg-K); 2.042E-05 Pa-s; 0.0293 W/(m-K).

Air is flowing through a 20 m long pipe of 20 cm diameter at a rate of 0.8 kg/s. The inlet air temperature is 40 deg C; the entire pipe wall is held at a constant temperature of 90 deg C. Estimate the air temperature at the outlet as well as the heat transfer rate for the entire length of the pipe. Properties are: 1.038 kg/m3; 1009 J/(kg-K); 2.042E-05 Pa-s; 0.0293 W/(m-K).

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.4P

See similar textbooks

Similar questions

Water enters a tube at 29°C with a flow rate of 460 kg/h. The rate of heat transfer from the tube wall to the fluid is given as qs′(W/m)=ax, where the coefficient a is 25 W/m2 and x(m) is the axial distance from the tube entrance. (a) Beginning with a properly defined differential control volume in the tube, derive an expression for the temperature distribution Tm(x) of the water. (b) What is the outlet temperature of the water for a heated section 31 m long? (c) Sketch the mean fluid temperature, Tm(x), and the tube wall temperature, Ts(x), as a function of distance along the tube for fully developed and developing flow conditions. (d) What value of a uniform wall heat flux, qs″ (instead of qs′=ax), would provide the same fluid outlet temperature as that determined in part 8.13b? For this type of heating, sketch the temperature distributions requested in part 8.13c.
300960 W (e) Water is entering a heated tube at mass flow rate of 1.2 kg/s. The temperature at the inlet is 20°C and at the outlet is 80°C. Assume the surface temperature of the tube is 100°C. The convection coefficient of the water flow is 28 W/m².°c. The specific heat and density of water can be assumed to be 4180 J/kg.°C and 990 kg/m³. What is the rate of heat transfer to water during this process?
43% uo 7:52 * ZAIN IQ I. sheet No.3.pdf Homework 01-03 -2021 one-dimensional heat transfer and disregarding radiation, determine the rate of heat transfer through the wall. Q4/ Steam at Te1-320°C flows in a cast iron pipe (k=80W/m.°C) whose inner and outer diameters are D =5cm, and D=5.5cm, respectively. The pipe is covered with 3 cm thick glass wool insulation with k=0.05W/m.°C. Heat is lost to the surroundings at T02=5°C_by natural convection and radiation, with a combined heat transfer coefficient to be h,=18W/m.C. Taking the heat transfer coefficient inside the pipe to be h,=60W/m.C, determine the rate of heat loss from the steam per unit length of the pipe. Also determine the temperature drops across the pipe shell and the insulation. 05/ Determine the overall heat transfer coefficient U based on the outer surface of a D=2.5cm, and D=3.34 cm steel pipe (k=54.0W/m.°C) for the following conditions: inside and outside heat transfer coefficients are 1200W/m."C. and 2000W/m."C…
For a water flow over a steel surface, the temperature of water at a specific location was found to change with the vertical distance from the surface (y) up to a distance of 0.015 m as T(y) = 60 + 20y + tan(y), where temperature is in °C and y is in cm. The surface temperature and ambient temperature was measured as 60°C and 105°C, respectively. The thermal conductivity of steel and water are, respectively, 48 W/m-K and 0.6 W/m-K. What is the local convection coefficient at this location?
(heat transfer ) thanks The velocity of the fluid flowing in parallel over a 500mmx500mm flat heater surface is U= 19 m/s and the inlet velocity temperature is T_∞15 C. The surface temperature of this plate is T_s140 C, the friction force is F_D=0.4 N and the surface area of the plate is A=0.32 m2. According to this;(F_D= 0.4N A=32 m2)a) Surface shear stressb) Find the coefficient of frictionc) Heat transfer coefficientd) What is the amount of heat transfer (electric power) that must be given to maintain a constant surface temperature?
Heat Transfer (Third year) 2020- 2021 Homework 01-03-2021 By Dr. Basil Noori Merzah one-dimensional heat transfer and disregarding radiation, determine the rate of heat transfer through the wall. Q4/ Steam at T01-320°C flows in a cast iron pipe (k=80W/m. C) whose inner and outer diameters are D,=5cm, and D,-5.5cm, respectively. The pipe is covered with 3 cm thick glass wool insulation with k=0.05W/m. C. Heat is lost to the surroundings at T2-5°C by natural convection and radiation, with a combined heat transfer coefficient to be h,=18W/m."C. Taking the heat transfer coefficient inside the pipe to be 2 0 h,-60W/m. C, determine the rate of heat loss from the steam per unit length of the pipe. Also determine the temperature drops across the pipe shell and the insulation. Q5/ Determine the overall heat transfer coefficient U based on the outer surface of a D=2.5cm, and D =3.34 cm steel pipe (k=54.0W/m. C) for the following conditions: inside and outside heat transfer coefficients are…
High-pressure steam condenses at 400 K on the outer surface of a thin-walled tube of 50 mm diameter. The overall heat transfer coefficient between steam and air on the inside of the tube is 200 W/m?. If the air enters the tube at 25 m/s, 150 kPa and 280 K, find the length of the tube required for the air to be heated to 350 K.
saturated steam at 110°C flows inside a steel pipe ( thermal conductivity 50W/mK) having an internal diameter of 10cm and external diameter of 12 cm . The surface heat transfer coefficient on steam side is 12 kW/m^2K and that onthe outside surface of pipe is 18W/m^2K . Determine the heat loss from the pipe if it is located in a space at 25 °C.
An incompressible fluid flows through a rectangular cross section duct, with width much larger than height of the cross section. The duct surface is heated at a uniform rate along its length. If the centreline of the flow is along the centre of the duct where y = 0, the distance from the centreline to the surface of the duct is b = 25 mm, and the thermal conductivity of the fluid is 0.6 W/mK, what is the local heat transfer coefficient in the developed region of the flow? Give your answer in W/m2K to 1 decimal place.
An incompressible fluid flows through a rectangular cross section duct, with width much larger than height of the cross section. The duct surface is heated at a uniform rate along its length. If the centreline of the flow is along the centre of the duct where y = 0, the distance from the centreline to the surface of the duct is b = 25 mm, and the thermal conductivity of the fluid is 0.6 W/mK, what is the local heat transfer coefficient in the developed region of the flow? Give your answer in W/m2K to 1 decimal place. I AM POSTIING THIS AGAIN. PLEASE STOP ? COPY FROM INTERNET AND SEND RANDOM SOLUTION. HINT THE FINAL ANSWER IS 38.4 But i need step by step solution. if you don't get this value don't send it please, reject and add the credit
350 pipes are fixed as square in a pipe bundle used for condenser. PipeThe outer diameters are 8 mm and the steam at 0.2 bar is desired to be condensed on the pipes. pipe outer The surface temperature is kept constant at 30 °C. If the length of the pipes is 1.5 m, the heat transferred in the systemCalculate the amount of energy and the amount of condensed steam
V(m/s) V(m/s) Q=2000 IIIIII air D-0.1m Air at (3.15x102) K is entering in a circular pipe at 101325 Pa as shown in Figure. The velocity of the air at the pipe entrance is (2.000x100) m/s. The diameter of the pipe is 0.1m. Specific gas constant of air is 287 3/kg-K. Specific heat of air is 1000 1/kg-K Find the outlet temperature i 2000 J of heat is added to the pipe.