Q1 Data obtained from a laboratory consolidation test are tabulated as follows: Test points I 2 3 4 5 o' (kPa) Total AH (mm) 20 50 100 0.23 0.87 L.90 3.62 5.55 7.25 200 400 800 G,=2.70, Ho= (initial thickness at zero pressure) = 22.5 mm, w = (moisture content at the beginning of the test) = 0.78. Plot the e-logo' curve and calculate Ce Ae I+eo Ho log a - logo, log(o /06) ΔΗ Hint: and

Q1 Data obtained from a laboratory consolidation test are tabulated as follows: Test points I 2 3 4 5 o' (kPa) Total AH (mm) 20 50 100 0.23 0.87 L.90 3.62 5.55 7.25 200 400 800 G,=2.70, Ho= (initial thickness at zero pressure) = 22.5 mm, w = (moisture content at the beginning of the test) = 0.78. Plot the e-logo' curve and calculate Ce Ae I+eo Ho log a - logo, log(o /06) ΔΗ Hint: and

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The specific gravity and absorption test (ASTM C128) were performed on fine aggregate. The following data were obtained.Given:Mass of SSD sand = 400.0 gMass of pycnometer with water = 520.0 gMass of pycnometer with water plus sand = 850.0 gMass of dry sand = 397.0 gRequired:a) absorption, in percentb) free moisture if the sand in the stockpile has a moisture content of 3% bbbbbbbbbbbbbb
Three samples of fine aggregate were taken from the same stockpile and have the properties shown below. Determine in percentage: (a) total moisture content of each sample, (b) free moisture content of each sample, and (c) the average values of each from the stockpile. Measure Wet Mass (g) Dry Mass (g) Absorption (%) A 521.0 491.6 2.5 Sample B 522.4 491.7 2.4 C 523.4 492.1 2.3
Q1: A: define the following: Steel corrosion, seasoning, fly ash, flash point, grout B: A severe weathering clay brick was tested for absorption and saturation coefficient according to ASTM C67 procedure and produced the following data: Dry mass of specimen = 2.186 kg Saturated mass after 24-hr submersion in cold water = 2.453 kg Saturated mass after 5-hr submersion in boiling water = 2.472 kg Calculate absorption by 24-hr submersion, absorption by 5-hr boiling, and saturation coefficient. Does the brick satisfy the ASTM requirements?
The specific gravity and absorption test (ASTM C128) were performed on fine aggregate. The following data were obtained.Given:Mass of SSD sand = 400.0 gMass of pycnometer with water = 520.0 gMass of pycnometer with water plus sand = 850.0 gMass of dry sand = 397.0 gRequired:a) bulk dry specific gravityb) bulk SSD specific gravityc) apparent specific gravity aaaaaaaaaa
Three samples of aggregates were taken weighed in moist and dry condition. Moist Dry Unit Absorption Volume (m3) Unit Aggregate Wt. Wt. (%) (kN/m3) (kN/m3) Sample 1 23.425 20.018 5.14 0.366 Sample 2 22.7 18.757 3.87 0.695 Sample 3 20.292 18.387 2.62 0.237 Where; Unit weight of water = 9.81 kN/m3 %3D Determine the average free moisture content of the three samples.
Indian Standard (IS) Light Compaction test is usually conducted in 3 layers in a 1000 cc mould. How many blows per layer would be necessary if the above test is conducted in a 2250 cc mould? COMAN0aWaaww VWWOW¶D@W¶DWW¶DⱭvⱭ❤aww/D/¶DUDUDDWYD.
From the tabulation of data and result of determining setting time of cement, determine the initial +setting time. Trial Time (seconds) Penetration (mm) 1 30 38 930 30 1830 24 2730 15
Three samples of fine aggregate have the properties shown below. Determine in percentage: (a) total moisture content and (b) free moisture content for each sample and the average of the three samples. Table P5.7 Measure Wet Mass (g) Dry Mass (g) Absorption (%) Sample A 521.0 491.6 2.5 B 522.4 491.7 2.4 C 523.4 492.1 2.3
Three samples of fine aggregate have the properties shown in Table P5.9. TABLE P5.9 Sample Measure A B Wet Mass (g) 521.0 522.4 523.4 Dry Mass (g) 491.6 491.7 492.1 Absorption (%) 2.5 2.4 2.3 Determine in percentage: (a) total moisture content and (b) free moisture content for each sample and the average of the three samples.
Three samples of aggregates were taken weighed in moist and dry condition. Moist Dry Unit Unit Absorption Volume Aggregate Wt. Wt. (%) (m³) (kN/m) (kN/m³) Sample 1 23.425 20.018 5.14 0.366 Sample 2 22.7 18.757 3.87 0.695 Sample 3 20.292 18.387 2.62 0.237 Where; Unit weight of water = 9.81 kN/m3 Determine the average free moisture content of the three samples.
Workability of concrete is measured in a concrete lab by compaction factor test. If the partial compacted concrete weight after deducting empty weight of cylinder 11.4 kg and fully compacted concrete weight after deducting empty weight of cylinder = 11.98 kg. Determine. compaction factor value. O a. 11.69 O b. 0.58 O c. 0.95 C. O d. -0.86 =
1. Calculate the following properties for the data provided in the Table below for a coarse aggregate sample. a. Bulk SSD specific gravity b. Bulk Dry specific gravity A Bulk Dry Sp. Gr. = c. Apparent specific gravity d. Absorption capacity. В — С B Bulk SSD Sp. Gr. = В — С where A Apparent Sp. Gr. = А — С A = dry weight B = SSD weight C = submerged weight В — А (100) A Absorption (%) Weight of Pan + Oven- Dry Aggregate Weight of Pan Weight of Submerged Aggregate Weight of Pan + SD Aggregate 0.8495 Ib 1.9885 lb 0.6870 lb 1.9630 Ib 2. If the Moisture Content of a stockpile sample of the same coarse aggregates is 1.85 %, what is the moisture state of aggregate sample? Select from the four standard moisture states. Explain how you arrived at the answer. 3. If Bulk unit weight of coarse aggerates is 98 Ib/ft³determine the % Voids of dry-rodded aggregate. Youlk S.G(Bulk Dry)*Pwater %Solids * 100 4. Determine the % solids for 2 cases discussed in pre-lab video by using below data.…