Three samples of aggregates were taken weighed in moist and dry condition. Moist Dry Unit Absorption Volume (m3) Unit Aggregate Wt. Wt. (%) (kN/m3) (kN/m3) Sample 1 23.425 20.018 5.14 0.366 Sample 2 22.7 18.757 3.87 0.695 Sample 3 20.292 18.387 2.62 0.237 Where; Unit weight of water = 9.81 kN/m3 %3D Determine the average free moisture content of the three samples.

Three samples of aggregates were taken weighed in moist and dry condition. Moist Dry Unit Absorption Volume (m3) Unit Aggregate Wt. Wt. (%) (kN/m3) (kN/m3) Sample 1 23.425 20.018 5.14 0.366 Sample 2 22.7 18.757 3.87 0.695 Sample 3 20.292 18.387 2.62 0.237 Where; Unit weight of water = 9.81 kN/m3 %3D Determine the average free moisture content of the three samples.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given that the absorption capacity of a sample of aggregates is 8.7% and the oven-dry mass of the sample is 1000 g. Determine the mass of water that this sample 'can absorb. O A. 43.50 O B. 8.70 O C. 870.00 O D. 0.87 O E. 87.00
1. Fineness modulus of the aggregate Weight Retained Individual Cumulative Percent Sieve (g) Percent Percent Passing 4.75mm 31.5 2.36mm 67.6 1.18mm 96.5 600um 111.1 300um 60.5 150um 115.6 75um 17.5 pan 31.5 O a. 2.96 O b. 2.76 O c. 2.54 O d. 2.34
Three samples of aggregates were taken weighed in moist and dry condition. Moist Dry Unit Unit Absorption Volume Aggregate Wt. Wt. (%) (m³) (kN/m) (kN/m³) Sample 1 23.425 20.018 5.14 0.366 Sample 2 22.7 18.757 3.87 0.695 Sample 3 20.292 18.387 2.62 0.237 Where; Unit weight of water = 9.81 kN/m3 Determine the average free moisture content of the three samples.
A sample of wet aggregate 297.2 N. After drying in an oven, this sample weighed 281.5. The absorption of this aggregates is 2.5%. Calculate the percent of free water in the original wet sample. Weight of the wet aggregates (Wwet) = 297.2 N Weight of the dry aggregates (Wdry) = 281.5 N
A 1875g of coarse aggregates was soaked for at least 24hours prior to the lab. It is then brought to saturated surface dry condition and weigh 1900g. The weight of the sample+basket when submerged to water was recorded to be 1650g and for oven dry condition sample was found to be 1600g. if the weight of the basket is 300g, determine the specific gravity and absorption of coarse aggregates.
Determined and fil-up the unknown data of the given table. Physical Properties Mix Design Specific Dry-rodded Materials Fineness Estimated Absolute gravity weight ft3 Absorption modulus Ib/yd3 Ib/yd3 (SSD) Ib/ft3 Cement 3.15 ? ? Sand 2.64 0.7 2.72 11/2 62.4 Ib/ft Gravel 2.67 0.5 100.5 Water ? Vol. of entrapped air w/C = ? GIVEN: Specification Requirements compressive strength, psi 4000 Slump, in. 3 4
Show conplete solution.
YALVE 3) Constont level constent level k 0.26 O-63 soyuB 0.48m According to the above figure given 760 me rater is collected in the container in 15 minutes.If kA is giver as kA= 2x 10m/s..calculate the permeability of isoil B (kR).Length of the Systen perpendicaelar to the Figure plane (thickness) is coefficent O.15 m. -0.2m
Calculate Brinell Hardness for Hardened AW-6060 Aluminium if mean depression ?diameters (d)= 5.64mm with applied load of 3000kgf 100 O 109 O 119 129
1. Fineness modulus of the aggregate Weight Retained Sieve Individual Percent Cumulative Percent Percent Passing (g) 4.75mm 31.5 2.36mm 67.6 1.18mm 96.5 600um 111.1 300um 60.5 150um 115.6 75um 17.5 pan 31.5
Data sheet Class .... Name...... Group No. 1. gypsum fineness: Weight of sample before sieving (W1) = 100 g Weight of the passed gypsum (in the pan) (W2) = 94 g Fineness, % = Signature: 2. Standard consistency: Weight of dried gypsum (W1)= 1000 g Weight of the empty graduated tube (W2) = 184 g Weight of the tube contain the water (W3)= 395 g Weight the remaining gypsum from (W1) after prosing (W4) = 558 g Normal (standard) consistency, % = Signature:
SURFACE MOISTURE OF FINE AND COARSE AGGREGATE Pycnometer or Flash Method make up computation, make one Mass of specimen (S) Mass of pycnometer + water (C) Mass of pycnometer + water + specimen (W) Mass of displaced water (V) Specific Gravity, G 2.86 D = S/G % surface moisture