A block of wood weighing 18 pounds rests on an inclined plane that makes an angle of 60 with the horizontal. How much of the friction force is needed to prevent the block from sliding on the plane? Round answer to nearest whole number. Do not use a space or decimal in your answer or it will be marked wrong.

A block of wood weighing 18 pounds rests on an inclined plane that makes an angle of 60 with the horizontal. How much of the friction force is needed to prevent the block from sliding on the plane? Round answer to nearest whole number. Do not use a space or decimal in your answer or it will be marked wrong.

Name: A block of wood weighing 18 pounds rests on an inclined plane that mak
Uploaded: 2024-03-20T06:56:46.000Z
Channel: Bartleby
Description: A block of wood weighing 18 pounds rests on an inclined plane that makes an angle of 60 with the horizontal. How much of the friction force is needed to prevent the block from sliding on the plane? Round answer to nearest whole number. Do not use a s

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter1: Physics And Measurement

Section: Chapter Questions

Problem 1.21P: The pyramid described in Problem 20 contains approximately 20 million stone blocks that average 2.50...

See similar textbooks

Similar questions

a post is supported by a guy wire which exerts a pull of 100N on the top of the post. if the angle between the wire and the ground is 60degrees , what is the horizontal component of the force supporting the pole? 3 dec places for final answer pls thank u
The coefficient of static friction between A and C and between B and D is g = 0.25, and between A and B is g = 0.46. Neglect the weight of each wedge. (Figure 1) Figure Part A Pmin = 19 Value 15° Units Determine the smallest force P needed to lift the 3000-lb load. Express your answer to three significant figures and include the appropriate units. A ? 3000 lb B D 1 of 1
1. If μ= 0.3, what will be the friction angle? 2. If the friction angle is 12 degrees, what will be the coefficient of friction?
The metal plate is held by two cables as shown in the following figure. If the force of each cable acting at A is FAB = 1000 Ib and FAc = 200 Ib. Determine the magnitude of the resultant force of the two forces acting at A. -8 ft- 8 ft 6 ft B FAR FAC A(10;6;0) Select one: O a. FR = 1010 lb O b. FR = 1100.21 lb O c. FR = 780.64 lb O d. FR = 1200 lb
12. In an experiment, a student measured the pulling force (the force required to move each block at a constant speed) and plotted the pulling force, in Newtons (N), versus block mass, i kilograms (kg). The results are shown in Figure 1. Based on Figure 1, the results of the experiment shown are best modeled by which of the following equations? * 25.00- Z 20.00- 15.00 10.00 5.00 0.00 0.00 block mass (kg) Figure 1 a. Block speed (m/sec) = 0.2 x time (sec) b. Pulling force (N) = 0.2 x block mass (kg) C. Block speed (m/sec) = 5.0 x time (sec) hp #3 & 大 7 pulling force (N) 0.50 1.50 000 00 3.50 00 00
you place a 5.000 g weight on the scale and the balance reads that the weight is 5.983 g. what is the percent error of the scale?
Problem 01: A force 200 N is directed as shown in figure. Determine the X and Y components of the force. Express your final answer in Kilonewton. 200 N 30° Problem 02: Determine the components of the 30u-N force directed down to the right at a slope of 2 to 3 as shown F = 300 N Problem 03: The components of a certain force are defined by . Determine the magnitude and inclination of of the resultant with the x-axis. Draw/plot your answer.
Will the 200N block shown in the figure be held in equilibrium by the force of 160N? The coefficient of static friction is 0.3. What is the actual friction force based on your calculation? P 45° Solution: A 1. There are in total 2. EF, = 0: N y 3. Fx = 0: fquired= 4. Maximum static friction fm = forces on the block, with the frictional force point to the 5. Hence the block will N; N; N; 6. The actual friction froce on the contacting surface is N
FORCE COMPONENTS: 1. Compute the X and Y Components of each of the forces. T=722 b P-200b. F-448lb. 2. Compute the X and Y Components of each of the forces. 200 lb 400 lb X 300 lb 300 lb
A force of 3.1 N makes an angle of 10o (counter-clockwise) with the +X axis. The Y component of the force is ____________ N. a. 3.05 N b. -5.41 N c. 0.55 N d. 0.54 N
5. Two forces have the same magnitude F. What is the angle between the two vectors if their sum has a magnitude of (a) 2F? (b) 22F? (c) zero? Sketch the three vectors in each case. 6. Two dogs pull horizontally on ropes attached to a post; the angle between the ropes is 60°. If dog A exerts a force of 270 N and dog B exerts a force of 300 N, find the magnitude of the resultant force and the angle it makes with dog A's rope. 7. A 68.5-kg skater moving initially at 2.40m/s on rough horizontal ice comes to rest uniformly in 3.52 s due to friction from the ice. What force does friction exert on the skater?
Consider a resultant force of 50 N along the negative y-axis. The resultant was calculated as a sum of the following four tensile forces: F1 = 100 N at 70°, F2 = 300 N at 190° and F3 150 N at 340° and F4 Find the magnitude and the direction of the force F4. Use the counter clockwise direction as the positive direction of the angle from the positive x-axis. Provide the answers to 2 decimal places. 1) Draw a force diagram to support your workings. 2) Compute the x-component of F4 according to the coordinate system shown. 3) Compute the y-component of F4 according to the coordinate system shown. 4) Compute the magnitude and the direction of F4. Define the direction of F4 from the positive x-axis; use the counter clockwise direction as the positive direction for the angle. 5) Draw a sketch of F4 (final values of the magnitude and direction in association with X and Y components).