7.33. These phenomena are observed in a laboratory channel 1 m wide, and the indicated measurements taken. Many velocity measurements at sections 1 and 2 allow calculation of B, and B2, which turn out to be 1.02 and 1.07, respectively. Calculate the total drag force exerted by the water on the walls and bottom of the length of channel between sections 1 and 2. 61 mm 76 mm 305 mm Horizontal 274 mm

7.33. These phenomena are observed in a laboratory channel 1 m wide, and the indicated measurements taken. Many velocity measurements at sections 1 and 2 allow calculation of B, and B2, which turn out to be 1.02 and 1.07, respectively. Calculate the total drag force exerted by the water on the walls and bottom of the length of channel between sections 1 and 2. 61 mm 76 mm 305 mm Horizontal 274 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1: Find the boundary layer thickness (6) equation, the shear stress (to) and the coefficient of drag (Cò ) if the velocity distribution in the laminar boundary layer over the face of a spillway was observed to be: *--(C)- ()*+C). U Then calculate the boundary layer thickness and drag force if the air flows over a sharp edged flat plate 0.25m long and 0.5m wide at a velocity 1 m/s, take the air density 1.23 kg/m³ and the kinematic viscosity is 1.46*10-5 m/s².
1. The given information is as follows: Cd=1.4 (coefficient of drag) ¥=10 ft/sec (velocity) Ƴ=62.4 #/ft3 g=32.3 ft/sec2 a. What is the water pressure in PSF against the obstruction? b. If the pier is 6 ft wide and 14 ft deep, what is the Resultant Pressure on the WHOLE obstruction? c. If the obstruction is fixed into the bottom of the river (mud line), what is the bending moment at the mudline on the obstruction?
A thin flat plate 55 x 110 cm is immersed in a 6 m/s stream of oil. What is the friction drag on one side of the plate if the flow is parallel to the long side? Use the density of oil as 891 kg/m3 and absolute viscosity of 0.29 Pa-s. a. 90 N b. 102 N c. 145 N d. 181 N
8.) A circular cylinder 4m long and 3m in diameter is in an air stream. The flow velocity is 5 m/s L parallel to the axis of the cylinder. Given that the coefficient of drag, CD on the cylinder is 1.3, and the density of air is 1.225 kg/m3. What is the force on the cylinder? A. 0.090 KN B. 0.14 KN C. 0.24 KN D. 0.91 kN
Air at 20 °C flows at V = 10 m/s over a flat plate of length L= 1.52 m and width W = 2 m.Calculate the boundary layer thickness at the trailing edge of plate and drag force on one sideof plate if:a. Surface of plate is smooth.b. Surface of plate is rough.The air properties at 20 °C are: Density, ? = 1.2 kg/m3and dynamic viscosity, ? = 1.8x 10-5kg/m·s and kinematic viscosity, ν = 1.516×10-5m2/s
Q1: Find the boundary layer thickness (8) equation, the shear stress (to) and the coefficient of drag (C₁) if the velocity distribution in the laminar boundary layer over the face of a spillway was observed to be: (40%) 2 5 --0-0-0) = 2 + Then calculate the boundary layer thickness and drag force if the air flows over a sharp edged flat plate 0.25m long and 0.5m wide at a velocity 1 m/s, take the air density 1.23 kg/m³ and the kinematic viscosity is 1.46*10-5 m/s².
Air at 20 °C flows at V = 10 m/s over a flat plate of length L= 1.52 m and width W = 2 m.Calculate the boundary layer thickness at the trailing edge of plate and drag force on one sideof plate if:a. Surface of plate is smooth.b. Surface of plate is rough.The air properties at 20 °C are: Density, ? = 1.2 kg/m3and dynamic viscosity, ? = 1.8x 10-5kg/m·s and kinematic viscosity, ν = 1.516×10-5m2/s. kindly give me the solution of this problem with correct and logical reasoning.
The large block shown is x = 72 cm wide, y = 54 cm long, and z = 9.0 cm high. This block is passing through air (density of air p = 1.43 kg/m³) at a speed of v = 8.61 m/s. Find the drag force F41 acting on the block when it has the velocity vj and a drag coefficient I = 0.812. V2 Fa.1 N %3D Find the drag force F42 acting on the block when it has the velocity vz with a drag coefficient I = 0.893. F42 N Find the drag force Fa.3 acting on the block when it has the velocity vz with a drag coefficient I = 1.06. F4.3 = N EN
Air at 20 °C flows at V = 10 m/s over a flat plate of length L= 1.52 m and width W = 2 m.Calculate the boundary layer thickness at the trailing edge of plate and drag force on one sideof plate if:a. Surface of plate is smooth.b. Surface of plate is rough.The air properties at 20 °C are: Density, ? = 1.2 kg/m3and dynamic viscosity, ? = 1.8x 10-5kg/m·s and kinematic viscosity, ν = 1.516×10-5m2/s. I got the first solution which was wrong kindly solve it correctly
The rectangular wing of a trainer aircraft has a wingspan of 15.5 m and a chord of 3 m, the chord being parallel to the direction of the airflow. The aircraft is flying at standard sea level conditions with a velocity of 102 mps. Considering laminar flow only, determine total skin friction drag (N, 2 decimals).
(b) A Formula 1 team tests their car in a wind tunnel at a scale of 50%, at a speed of Vwinarunnet = 50 m/s. The measured downforce at this speed is Foownforce.WT = 3000 N and the model reference area is Aref wT = 0.5 m?. 1. Find the downforce magnitude on the full-scale race car at the same Reynolds number. Assume constant air density p = 1.2 kg/m. II. It is said that F1 cars could travel upside down, as shown below. At what speed should the full-scale car travel to achieve this, if its mass is m = 740 kg? The acceleration of gravity is g = 9.81 m/s?. Downforce Weight
A fighter aircraft is to operate at 200 m/s in air at standard conditions ( = 1.2 kg/m3). Amodel is constructed to 1/20 scale (length ratio) and tested in a wind tunnel at the sameair temperature (same air viscosity) to determine the drag force. The drag force FD is afunction of the air density  and viscosity , the velocity V and the cross section length ofthe airplane D.