2 Questions 1) What is a semiconductor? state the different between p-type and n-type material? 2) How many equivalent circuits model of diode? explain each model in detail. 3) What is the advantage of FET compare to BJT? 4) Calculate the value of current and voltage in circuit below? 12V 2ΚΩ Si Ge 11 0.5kΩ Vo 1₂ ΑΚΩ ww Ge

2 Questions 1) What is a semiconductor? state the different between p-type and n-type material? 2) How many equivalent circuits model of diode? explain each model in detail. 3) What is the advantage of FET compare to BJT? 4) Calculate the value of current and voltage in circuit below? 12V 2ΚΩ Si Ge 11 0.5kΩ Vo 1₂ ΑΚΩ ww Ge

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
What is CEMF?
Consider the circuit shown in Figure 2. The cut-in voltage of each diode is . Let and assume both diodes are conducting. Determine if this is a valid assumption and explain your answer. And calculate the values of IR, ID, Ip2, and V.. Rj =1.7 kQ ww VB =1 V D1 Dz R2D 4 kQ Figure 2
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
Q1/Consider the circuit in Figure with a transformer of 10:1 transformation ratio and the diodes are silicon. a) What type of circuit is this? (b) What is the total peak secondary voltage? (c) Find the voltage value across the resistor (d) Sketch the voltage waveform across RL (e) What is the PIV for each diode? D3 D 120 V Pisez) Vpouo D D 10 kn lleee
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
For the circuit shown in the Figure, if the diodes are silicon diodes with VD(on)=0.7 V, and VIn=50 sin wt V, V1 =7 V and V2 =13 V, then the value of VOUT (p-p) is: R1 D, D2 VIN VOUT vi E v2= Ca. 19.4 V Ob. 17.4 V Cc. 15.4 V Cd. 21.4 V
a) What is n-type semiconductor materials? What are the majority and the minority cariers? b) What is p-type semiconductor materials? What are the majority and the minority cariers? c) What is depletion region of a p-n junction diode? d) Describe in your own words the forward-bias and reverse- bias conditions of a p-n junction diode. e) Draw a Diode Symbol and label the anode and the cathode. Si Ge 2 ka f) Find V, in the circuit shown in +20 V 2 k2 15V Fig. Fuad Al-Mannai EENG261 Page 1
In each of the ideal-diode circuits show below V1 is a 1kHz, 10-V peak sine wave. Sketch the wave form resulting at V0. What are its positive and negative peak values?
Q2:- Find the level of Vo for each circuit shown in the Figure below. Also, determine the status of each diode; if it is forward or reverses biasing. Assume all diodes are silicone with 0.7v drop. +5 V +15 V -10 V (12 Marks) R DI +5 VoK D +5 VoK DI -5 VoH -5 Vo4 D2 D2 D2 +5 VoH D3 +5 Vo4 D3 -10 VoK D4 V. -5 Vo K (a) (b)
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
4.) In which mode will a diode generally not conduct electricity? a. Bidirectional Biased b. None of these c. Forward Biased d. Reversed Biased 5.) Consider the following schematic symbol of a semiconductor device: Which side is the Cathode? (Picture inserted down below) a. Side A b. Both side A and B c. Side B d. Neither side A or B 8.) Integrated circuits can be broken down into three basic categories. Which category does an operational amplifier (or op-amp) fall into? a. Analog b. None of these c. A combination of analog and digital d. Digital