1.7 (A). A bar ABCD consists of three sections: AB is 25 mm square and 50 mm long, BC is of 20 mm diameter and 40 mm long and CD is of 12 mm diameter and 50 mm long. Determine the stress set up in each section of the bar when it is subjected to an axial tensile load of 20 kN. What will be the total extension of the bar under this load? For the bar material, E 210 GN/m². [32, 63.7, 176.8 MN/m², 0.062 mm.]

1.7 (A). A bar ABCD consists of three sections: AB is 25 mm square and 50 mm long, BC is of 20 mm diameter and 40 mm long and CD is of 12 mm diameter and 50 mm long. Determine the stress set up in each section of the bar when it is subjected to an axial tensile load of 20 kN. What will be the total extension of the bar under this load? For the bar material, E 210 GN/m². [32, 63.7, 176.8 MN/m², 0.062 mm.]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A BRONZE ROD IS SUBJECTED TO A TENSILE LOAD OF 15,000N. IF ITS ALLOWABLE STRESS IS 75 MPa, CALCULATE THE OUTER LENGTH OF THE SIDE OF THE PENTAGONAL TUBE IF THE INNER LENGTH OF THE ONE SIDE IS 40mm. 15,000N 15,000N 40mm CROSS-SECTION OF THE BRONZE ROD BRONZE ROD
The P load applied to a steel bar is transferred to the board by an annular washer. The diameter of the rod is 34mm and the inner diameter of the washer is 35.7 mm. Since it is known that the axial normal stress on the steel bar is 119 MPa, and the average bearing stress between the washer and the board should not exceed 34 MPA, how many mm is the smallest allowable outer diameter of the washer?
. (A). A bar ABCD consists of three sections: AB is 25 mm square and 50 mm long, BC is of 20 mm diameter and 40 mm long and CD is of 12 mm diameter and 50 mm long. Determine the stress set up in each section of the bar when it is subjected to an axial the bar material, E = 210GN/m?. tensile load of 20 kN. What will be the total extension of the bar under this load? For [32.63.7, 176.8 MN/m2, 0.062mm]
1. A 300mm long composite bar is constructed by bonding an alloy steel outer sleeve of outside diameter 75 mm to a solid mild steel core of diameter 67 mm. A tensile force of 200kN was applied to the composite bar. If the modulus of elasticity for the mild steel is 208 GN/m² and that for the alloy steel is 360 GN/m². Determine the following values for the composite bar: Calculate: a) The stress in the mild steel core. a) The stress in the alloy steel sleeve. a) The extension under loading of the composite bar.
Question 4 A composite rod of 160 mm in length, is composed of 50 mm in diameter for a length of 100 mm and 30 mm for the remaining 60 mm. If the Young modulus of the composite is 200 GPa and the application of gradual load P in the rod results in storing 10 J of energy, calaculate: The magnitude of the applied load 4.1 4.2 The value of the stress in each section 4.3 The total extension 4.4 If this load had been applied suddenly but without shock or impact, what instantaneous maximum stress would have been induced in the link?
An engineering machine component operating in a high temperature environment consists of a copper pipe having a cross-sectional area of 2 000 mm² and 0.3 m long, which is placed between two rigid caps. Four M22 steel bolts are symmetrically arranged around the tube and parallel to the axis of the tube and are lightly tightened. 3.1 Find the stress in the pipe and the bolts if the temperature of the assembly is increased from 25 °C to 95 °C. 3.2 What load will each bolt carry at the raised temperature? 3.3 Make a neat sketch of the assembly. (Est = 200 GPa, Ecu – 100 GPa, as: = 12 × 10-6/ °C, acu = 16 × 10-6/ °C)
(a) Two vertical rods, one of steel and other of copper are each rigidly fixed at the top and 60 cm apart. Diameters and lengths of each of the rod are 3 cm and 3.5 cm, respectively. A crossbar fixed to the rods at the lower ends carried a load of 6000 N such that the crossbar remains horizontal even after loading. Find the stress in each rod and the position of the load on the bar. Take E for the steel as 2 x 10° N/mm² and for copper as 1 x 10° N/mm?.
As shown, three steel wires, each 28 mm2 in area, are used to lift a mass M. Their unstretched lengths are 19.99 m, 19.98 m, and 20 m. If M= 1,182 kg. what stress exists in the MIDDLE wire? Use E=215 Gpa. Answer must be in MPa.
P (1) B A A metal rod having two different diameters is loaded by an axial force P. Segments (1) and (2) are circular section diameters of 50 mm and 25 mm, respectively. If the normal stress in (1) is 40 MPa. Determine the following: The area of Segment (1) is equal to in mm?: The area of Segment (2) is equal to in mm²: The axial force (P) is equal to in kPa: The Normal Stress in Segment (2) is equal to in MPa:
1. (A). A 25mm square cross-section bar of length 300mm carries an axial compressive load of 50kN. Determine the stress set up in the bar and its change of length when the load is applied. For the bar material E = 200 GN/m. [80 MN/m², 0.12mm] 2. (A). A steel tube, 25 mm outside diameter and 12mm inside diameter, cames an axial tensile load of 40 kN. What will be the stress in the bar? What further increase in load is possible if the stress in the bar is limited to 225 MN/m?? [106 MN/m²; 45 kN]
6. (A). A bar ABCD consists of three sections: AB is 25 mm square and 50 mm long, BC is of 20 mm diameter and40 mm long and CD is of 12 mm diameter and 50 mm long. Determine the stress set up in each section of the bar when it is subjected to an axial tensile load of 20 kN. What will be the total extension of the bar under this load? For the bar material, E = 210GN/m². [32,63.7, 176.8 MN/m², 0.062mm]
3. A circular bar rigidly fixed at its both ends is 1.2 m long. It uniformly tapers from 100 mm at one end to 75 mm at the other. What is the maximum stress induced in the bar, when its tempera- ture is raised through 25 K? Take E as 200 GPa and a as 12 x 10/K. [Ans. 80 MPa] unifor from 00 to 60