Rotation of bar OA is controlled by the lead screw which imparts a horizontal velocity v to collar Cand causes pin P to travel along the smooth slot. Determine the values of rand 0, where r = OP, if h = 255 mm, x = 185 mm, and v= 32 mm/s at the instant represented. h Answers: ŕ= 18.79 0= i 0.08 x C mm/s Pv rad/s A

Rotation of bar OA is controlled by the lead screw which imparts a horizontal velocity v to collar Cand causes pin P to travel along the smooth slot. Determine the values of rand 0, where r = OP, if h = 255 mm, x = 185 mm, and v= 32 mm/s at the instant represented. h Answers: ŕ= 18.79 0= i 0.08 x C mm/s Pv rad/s A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

α v= A t = B Oh no! A very sad kitty is trapped on a little platform connected to a gear system, the little scoundrel! The cat is 10 feet below the cliff's edge and is too terrified to jump! Quick! Rotate the wheel at A at 4 rad/s to raise the poor creature to safety. At what speed does the platform raise? How long will it take the kitty to reach the top of the clliff's edge? The diameter of the crank and gears are dд = 1 ft, dß = 2 ft, dc = 6 ft, and dp = 2 ft D ft S www S
The pulley shown rotates at 10rad/s clockwise. Find the velocity of weight A (use up as + for the sign convention). You must show your work and include a diagram Hint: The distance between the fixed pulley and bottom ground is a constant Upload
The telephone-cable reel is rolled down the incline by the cable leading from the upper drum and wrapped around the inner hub of the reel. If the upper drum is turned at the constant rate w₁ = 2.8 rad/s, calculate the time required for the center of the reel to move 85 ft along the incline. No slipping occurs. 40" Answer: t = sec 12" 16" 001
Q5-A) A rope pulls the block up the ramp as shown in the figure. Find the following: 1. Draw a free body diagram for the block. a = 4.3 m/s? T = 2. Write the equation that sums the forces on the block that are parallel to the ramp. 3. Write the equation that sums the forces on the block that are perpendicular to the ramp. 4. What is the acceleration of the block perpendicular to the ramp? 5. What is the friction force? k = 0.45 6.0 kg 0= 30° 6. What is the tension force?
Determine acceleration U = 0.9mls V = 0.45mls += 15
Bar AB is rotating about A with an angular velocity of wAB 2 rad/s counterclockwise. At this instant bar BC is horizontal. Find the Wac and also, velocity of collar C. Note. You must solve the problem in the way that we solved in the class. Use Vg VA+ wX TB/A and express the vectors in Cartesian vector form. Other solutions will not be evaluated. Solve the problem step by step, and clearly show your work. 25 35 mm 170 mm
Use 3 decimal places The 250-N block rests upon a level plane for which fk = 0.2. It is pulled by force P = 100N inclined at 20o with the horizontal. 1. Find the velocity of the block after it moves 20m starting from rest. 2. If the 100-N pull is then removed, find the distance the block will travel.
The rod OA rotates clockwise at a constant angular velocity of 0 = (3) rad -. Two pin-connected slider block, located at B, move freely on OA. The curved rod is described by the equationr = (250 · (8 - cos 0)) m. Hint: 1. Remember clockwise rotation is negative velocity. A d3 d1 d2 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value 01 130 degrees di 0.45 m d2 dz 0.2 m 0.325 m Using cylindrical components, a. Determine the cylinders's radial and transverse components of velocity at the instant shown, vr and b. Determine the cylinders's radial and transverse components of acceleration at the instant shown, a, and ag. c. Determine the cylinder's magnitude of the velocity at the instant shown, v d. Determine the cylinder's magnitude of the acceleration at the instant shown, a
Bodies A and B shown in the figure are connected to each other by two ropes. Body b is located on the frictionless surface. Acismi moves down from the stop position at T=0 with a constant acceleration of 100 mm/sec2. t = 2 sec how many mm do Bodies A and B move, respectively? в A Please select one: a.200 mm down, 50 mm right b.200 mm down, 200 mm right c.200 mm down, 800 mm right d. None of them e.200 mm down, 400 mm right
Use 3 decimal places The 250-N block rests upon a level plane for which fk = 0.2. It is pulled by force P = 100N inclined at 20o with the horizontal. 1. If the 100-N pull is then removed, find the distance the block will travel. 2. Find the velocity of the block after it moves 20m starting from rest.
re 0.125 m vo irr 0.6 m 0.175 m wkransfun 0 B Part A If the center O of the gear is given a velocity of vo= 5 m/s, determine the speed of the slider block B at the instant 0 = 32 °. (Figure 1) Express your answer to three significant figures and include the appropriate units. UB= Submit μA Value Request Answer < Return to Assignment Units Provide Feedback ?
Link BC (of length 0.47 m) is pin connected at the fixed point C and makes an angleof ⍬ = 51° with the vertical. This link is connected to the vertical link AB (of length0.3 m) and point A is also the axle of a wheel of negligible size that is moving alonga circular track of radius r =2.3 m. If the speed of A is constant and VA = (-2.59)im/s, which one of the following statements is correct? (In the followingstatements, wAB and wBC denote ⍵AB and ⍵BC respectively, where both are definedpositive in the k-direction and given in rad/s, and A denotes the magnitude of pointA's acceleration in m/s2) 1) wAB=0; wBC=0; aA=02) wAB=6,99; wBC=-7.09; aA=03) wAB=8.63; wBC=0; aA=04) wAB=8.63; wBC=0; aA >0 5) wAB=6.99; wBC=-7.09, aA>0