1. We can visualize the factor of safety for an arbitrary stress using a surface in principal stress space. For a ductile material that yields according to a von Mises criterion with a yield stress σy, sketch the von Mises surface in σ₁ - 02 space and sketch the stress surface that corresponds to a factor of safety FoS = 2. For a brittle material that yields according to a max normal (Rankine) criterion with a tensile strength Gyt and a compressive strength σvc = 20yt, sketch the yield surface and the surface that corresponds to a factor of safety FoS = 2.

1. We can visualize the factor of safety for an arbitrary stress using a surface in principal stress space. For a ductile material that yields according to a von Mises criterion with a yield stress σy, sketch the von Mises surface in σ₁ - 02 space and sketch the stress surface that corresponds to a factor of safety FoS = 2. For a brittle material that yields according to a max normal (Rankine) criterion with a tensile strength Gyt and a compressive strength σvc = 20yt, sketch the yield surface and the surface that corresponds to a factor of safety FoS = 2.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.12P: Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in...

See similar textbooks

Similar questions

A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in tension is 975 MPa, the yield stress in shear is 460 MPa, the factor of safety is 2,75, the modulus of elasticity is 210 GPa, Poissorfs ratio is 0.28, and the normal strain must not exceed 1190 x 10" . For part (b), assume that the tank thickness is 8 mm and the measured normal strain is 990 x 10~ .
Problem 6 Estimate the Brinell and Rockwell hardness for the naval brass for which the stress-strain behavior is shown in the figure. Stress (MPa) 500 400 300 200 100 Tensile strength 450 MPa (65,000 psi) A MPa 40 200 100 10³ psi 0.10 30 20 10 I 0.20 Strain Yield strength 250 MPa (36,000 psi) 0.005 0.30 70 60 50 40 30 20 10 0.40 Stress (10³ psi)
A brittle material made of ASTM grade 30 cast iron has ultimate strength in tension of 31 kpsi and ultimate strength in compression of 109 kpsi and undergoes the following plane of stress state: o, = 20 kpsi and Tyy = 10 kpsi (CW). a) using the 3D Mohr's circle, find all three principal normal stresses. b) using the Brittle-Coulomb-Mohr theory and Modified-Mohr theory, find the factors of safety for the given plane of stress state.
In the picture there is a sketch of a socket wrench. Assume the wrench is held at a fixed point “A”. The yield stress of the material is known to be 400 MPa. Answer the questions below Describe the stresses at point “A” and their causes and calculate the stresses. Determine the factor of safety against yield assuming the Tresca yield criteria. Determine the factor of safety against yield assuming the von Mises yield criteria using both principal stresses and “Cartesian” stresses. Do your values match or not, and is this expected? Explain. Do the calculated values make sense with the respect to the Tresca value? Explain, why or why not?
A simple rod acted by fluctuating axial force produced a fluctuating stresses as Sigma_min=100MPA, Sigma_max = 500MPA, using mod-goodman answer Q1- Q5 (Sy = 400MPA, Sut = 600MPA) %3D * The equivalent fully reversed stress is
In the attached picture there is a sketch of a socket wrench. Assume the wrench is held at a fixed point “A”. The yield stress of the material is known to be 500 MPa. Answer the questions below Describe the stresses at point “A” and their causes and calculate the stresses. Determine the factor of safety against yield assuming the Tresca yield criteria. Determine the factor of safety against yield assuming the von Mises yield criteria using both principal stresses and “Cartesian” stresses. Do your values match or not, and is this expected? Explain. Do the calculated values make sense with the respect to the Tresca value? Explain, why or why not?
Example: Convert the change in length data in Table 3-2 to engineering stress and strain and plot a stress-strain curve Homework- help Table 3-2 The results of a tensile test of a 0.505 in. diameter aluminum alloy test bar, initial length (1o) = 2 in. Calculated LTO Load (Ib) Change in Length (in.) Stress (psi) Strain (in./in.) 0.000 1000 0.001 0.0005 4,993 14,978 24,963 34,948 37,445 39,442 39,941 39,691 37,944 3000 0.003 0.0015 5000 0.005 0.0025 7000 0.007 0.0035 7500 0.030 0.0150 7900 0.080 0.0400 8000 (maximum load) 0.120 0.0600 7950 0.160 0.0800 7600 (fracture) 0.205 0.1025
1. A part made of Aluminum 6061-T6 has a yield strength = 400 MPa. For each stress state below, draw all 3 Mohr's circles, find the principal stresses, and calculate the safety factor against yield using both the distortion-energy (von Mises) and maximum shear stress (Tresca) criterions. (If relevant) A clearly labeled diagram (or diagrams) clearly pertaining to your analysis with a coordinate system and relevant labels. Final answer with appropriate units and significant figures. You can use the fprintf() command in MATLAB to format numerical results A 2-3 sentence reflection on your answer. Does it make sense? Why or why not? What are some implications?
i li. الامتحان هو سؤالان فقط Q. 1: If a material is cast iron (ultimate tensile strength = 300 Mpa, ultimate compressive strength - 900 Mpa) and the stress state at a point is shown in Fig. 1. Using a graphical method, find safety factor against static failure using 100 Mpa (a) Rankine failure theory (b) Coloumb - Mohr theory (c) Modified Coloumb - Mohr theory 50 Мра إضافة ملف Q.2 For a rotating shaft of diameter 15 mm as shown in Fig. 2. If the material is AISI-1045 CD, Find the safety factor II >
(d) Define Modulus of Resilience 2. Draw the stress-strain diagram for a typical ductile material and locate the salient points onit 3. A bar of 25 mm diameter is tested in tension. It is observed that when a load of 60 kN is applied, the measured over a gauge length of 200 mm is 0.12 mm and contraction in diameter is 0.0045 mm. Find Poissa 4. A circular rod of diameter 16 mm and 500 mm long is subjected to a tensile force 40 kN. The modulus of e steel may be taken as 200 kN/mm?. Find the elongation and strainin the bar due to applied load. 5. Define (a) Resilience (b) Proof resilience PART -B structions: Part B consists of 3 Units. Answer any one full question from each unit. Each questioncarries 8 marks and may have su 1. A steel circular bar has three segments as shown in the fig. Determine the total elongation ofthe bar. Take E = 210 GPa. 300 kNI 330 kN 30 mm 50KN 15 mm 20 mm 80 kN A + 150 mm 200 mm 250 mm B. D (OR)