A beam ABC, having flexural rigidity El = 75 kN.m², is loaded by a force P = 1.2 kN at end C and tieddown at end A by a wire having axial rigidity EA= 900 kN, as shown in figure below. Using thesuperposition method, calculate the deflection and slope at point C.AB0.5 m0.5 m0.75 mDAnswer:5(mm)=5.244e (rad)= 0.00279950X

Step 1: Solve reactive forces Step 2: Compute deflection using integration method Step 3: boundary…

Answered: A beam ABC, having flexural rigidity El…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.6.10P: -10 The simple beam AB shown in the figure supports two equal concentrated loads P: one acting...

See similar textbooks

Similar questions

The cantilever beam ACE shown in the figure has FlexuraI rigidity EI = 2,1 x 106kip-in". Calculate the downward deflections Scand 8Sat points C and B, respectively, due to the simultaneous action of the moment of 35 kip-in. applied at point C and the concentrated load of 2,5 kips applied at the free end B.
Beam ACE hangs from two springs, as shown in the figure. The springs have stiffnesses kxand k2and the beam has flex lira I rigidity EL (a) What is the downward displacement of point C, which is at the midpoint of the beam, when the moment M0 is applied? Data for the structure are as follows: M0= 10,0 kN m, L = 1.8 m, EI = 216 kN m2, Jt, = 250 kN/m, and k2= 160 kN/m, (b) Repeat part (a), but remove A/() and apply a uniform load q — 3.5 kN/m to the entire beam.
-10 The simple beam AB shown in the figure supports two equal concentrated loads P: one acting downward and the other upward. Determine the angle of rotation A at the left-hand end, the deflection 1under the downward load, and the deflection 2 at the midpoint of the beam.
Beam ABC is loaded by a uniform load q and point load P at joint C. Using the method of superposition, calculate the deflection at joint C. Assume that L = 4 m, a =2ra, q = 15 kN/m, P = 7.5 kN, £ = 200 GPa, and / = 70.8 X 106 mm4.
For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the beam, (b) the slope at A, (c) the slope at B, and (d) the deflection at midspan. Assume that El is constant for the beam. Let Mo = 50KN-m, L= 4.5 m, E= 180 GPa, and I = 115x 106 mm4. Mo B Answer: (b) 0A = i rad (c) Og = i rad (d) vmid = i mm
Question 2 A beam ABC of length 3m has one support at the left end and the other support at a distance 2m from the left end. The beam carries an uniformly distributed load W=16 kN/m. Given E = 2 x 10$ N/mm? and I = 80 × 106 mm4. a. Find the slopes at the left support A. b. Find the deflection at the right end c. Find the maximum deflection between the supports. W A C 2 m 3 m Figure 2.
Q 2. Calculate the slope and deflection at the free end of the cantilever beam shown in figure using Method of super position Take. E = 2.05 x 10$ N/mm2 and I = Y x 10% mm“. %3D If the last two digits of student id 2 50, then take Y = last two digits of id /100. If the last two digits of student id < 50, then take Y = last two digits of id /10; If last two digits of id are zeroes, then take Y= 0.75 2 kN 6 kN/m 1.2 kN-m 3 m 2.2 EI
For a beam subjected to the load F at the center of the span as shown below, please 1. Find the maximum allowed load F, given a. Modulus of Rupture (MOR) of the material for the beam = 130 GPa b. Beam width b = 0.02m and depth d = 0.05m c. Span length L = 10m 2. If the maximum allowed load F is designed to be 40,000N, given all other conditions the same, what is the minimum MOR required for the material to make the beam? 3. If the maximum allowed load F is designed to be 50,000N, given all other conditions (MOR = 130 GPa) the same, what is the minimum depth d required? F b ✰ d ↓ D L
A 2 m B w = 24 kN/m Figure 1. An overhang beam with constant EI, and is being supported by a pin at A and roller at B, with a free end at C. 1m C Part 1: Use only the Area-Moment method. Draw the M/EI diagram with B as the reference point. Clearly Indicate the values (in terms of EI). 1. 2. Determine the slope at free end C with respect to B (in terms of EI). 3. Determine the deflection at free end C (in terms of EI).
7.17 The figure shows a steel beam which is fixedly clamped in A, and which rests on a roller bearing in B. The beam is 5 meters long, and is loaded with a bending moment of 25 kNm at the end. The bearing in B is removed. The cross section is rectangular, with a width of 50 mm. Determine the required height of the cross section when the maximum allowable deflection is 5 mm. Cross section: 25 kNm A h 5 m 50 mm
beam, simply supported at its ends, carries a load which increases uniformly from 15kN/m at the left-hand end to 100 kN/m at the right-hand end. If the beam is 5m long, find the equation for the rate of loading and, using this, to determine the deflection of the beam at mid-span if E= 200GN/m² and I=600*10 m².
A beam of uniform rectangular section 200 mm wide and 300 mm deep is simply supported at its ends. It carries a uniformly distributed load of 9 KN/m run over the entire span of 5 m. if the value of E for the beam material is 1 X 104 N/mm2 , find the slope at the supports and maximum deflection. Give me complete solution based on the given above. Again I need to ask the same question since you gave me a wrong answer before.

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS