M3

True Story! The 1998-1999 Mars Climate Orbiter mission was declared a total loss in1999 as there was a unit conversion mismatch error between Lockheed Martin and NASA. Themismatch was in the thruster force units. NASA used the SI system which called forNewton-Seconds (4.45 times as large) of thrust and Lockheed Martin used Pound-Force Seconds.Calculations placed the Orbiter at 68 miles from the surface as it went into orbit, but it waswithin 57 km of the surface after the breaking maneuver. Any distance from the surface lessthan 50 miles would have caused the Orbiter to crash.a. What was the actual distance of the Orbiter from the surface in miles?b. In percentage, how far off from the calculated 68 miles was the Orbiter?

A robot is used for loading and unloading of parts to automated flexible machines. Loading time is 1 minute; unloading time is 1.5 minutes; machining time 15 minutes; Robot travel time between the machines including the inspection time is 3 minutes. Cost of robot C,=30 TL/Hour; cost of machines C2=40 TL/Hour. How many machines (integer number) should be assigned to the robot so that the total robot and machine costs per cycle are minimized? 8 - 176 a) 4 b) 3 c) 2 d) e) 6.

Points: 0 of 6 Save Suppose that you are stranded-your rocket engine has failed-on an asteroid of diameter 3 miles, with density equal to that of the earth with radius 3,960 miles If you have enough spring in your legs to jump 4.9 feet straight up on earth while wearing your space suit, can you blast off from this asteroid using leg power alone? ft Note that the escape velocity on Earth is about 36,680 Select the correct choice below and fill in the answer box to complete your choice. (Type integers or decimals rounded to two decimal places as needed.) ft ft is less than your initial velocity when jumping, O A. Yes, you can blast off because the escape velocity of the asteroid, ft is greater than your initial velocity when jumping. O B. No, you cannot blast off because the escape velocity of the asteroid,

|Read the problem statement and the solution provided. There may or may not be one or more mistakes in the solution. Go through the solution carefully and then do the following. 1. State if the solution is correct or incorrect 2. If the solution is incorrect, identify what is the mistake in the solution. Be specific and succinct. 3. If the solution is incorrect, provide the final solution with appropriate steps. You can make the corrections directly on a copy of this provided solution, but make sure you clearly explain the corrections. Problem: Consider fully-developed flow of water through a 24-cm diameter tube. The water comes in at 20°C and exits at 40°C. The surface temperature of the tube is uniform at 60°C. The water flow has a mass flow rate of 0.24 kg/s. What is the average convection coefficient of the water flow? Solution: We have T, = 60°C, Tmi = 20°C, Tmo = 40°C, So, the bulk-mean temperature is Tm = 30°C. The appropriate properties are: u = 7.98 × 10-4 kg/ms; k = 0.615…

Part A- Finding the het friction force Learning Goal: To set up and evaluate the equations of motion in a normal-tangential coordinate system. The car is traveling at a speed of 62.5 ft/s, which is increasing at a rate of 4.55 ft/s? , and the curvature of the road is p = 710 ft. What is the magnitude of the net frictional force that the road exerts on the tires? Express your answer to three significant figures and include the appropriate units. A car of weight 3850 lb is traveling around a curve of constant curvature p.(Figure 1) • View Available Hint(s) Figure 1 of 1> F = Value Units Submit Part B - Finding the maximum allowable acceleration 2080 lb. If the car is traveling at 64.5 ft/s and the Suppose that the tires are capable of exerting a maximum friction force curvature of the road is p = 410 ft , what is the maximum tangetial acceleration that the car can have without sliding? Express your answer to three significant figures and include the appropriate units. > View Available…

please send handwritten solution Q3 part a ii

ADAMSON UNIVERSITY College of Engineering Civil Engineering Department Answer Sheet Name: Date: Course: Time: 4m 4m 100 t 200 kat

Assignment 1: TIME VALUE OF MONEY Objective: To further understand the concept of the time value of money. INSTRUCTIONS: In each problem, a. Translate data given in problems into their respective graphical representations - i.e. draw the correct cash flow diagram. b. Write down all pertinent given information or data on your paper. c. Calculate answers correctly. 3. A certain college graduate, Sallie Evans, has $24,000 in student-loan debt at the end of her college career. The interest rate on this debt is 0.75% per month. If monthly payments on this loan are $432.61, how many months will it take for Sallie to repay the entire loan?

O Web C x k GECO0 X O Course X O Assign X O Web C x k MATHO X Assign X O Discus: X O Quizze O Syllabu x O Grade: x om/courses/31937/assignments/1001318?module_item_id=2616268 tructions: ollow the prescribed format by the course policy pu have 48 hours to answer and submit the solution. olve the problem with complete and detailed solution. 7x+14] -x 1. What value of x satisfies the matrix equation (2 points) 3x-2 x+8 2. Solve for x and y in the matrix equation below: 3 -4 y x-y 4 2] [10 -1] 3 -1] %3D (3 Points) -1 [2 -3] x -8 2 6х -9 -3 3х |1 -2 2 and the matrix 3(A +2B) is equal to? (3 points) 3. For matrices A=| 0 %3D 7 -2 3 -1 [2 -3 The matrix product 2 4 ?(2 points) 4. 0 1 1 4,

please send handwritten solution Q3 part b complete

est 2 (copy) (page 4 of 9) A wiseup.wsu.acza/mod/quiz/attempt.php7attempt=610918cmid 148960&page=3 ops O YouTube M Gmail Maps O GENERAL MATHEM. O New Tab :WSU WiSeUp 1 MONLO GOA ashboard / My courses / FLM15B2_KF_WS6222 2021 / Tests / Test 2 (copy) uestion 4 Quz navigation Gate AB in Figure below is 1.0 m long and 0.9 wide. Calculate force F on the gate and position X of its centre of Not yet answered pressure. Marked out of Finish attempt 10,000 Rag question 3m Oil, s.g.=Q81 7m 1.0m B 50 Answer

A LESSON-2( SEAT WORK, PROE X Baby Hit Head: What to Look O Concussion: Symptoms, Diag x b Answered: 4. Replace the cop O Slide 1 LESSON-2( SEAT WORK, PROBLEM pm/u/0/c/Mjk1NjM4NTI4NTM3/a/MzA3NDcxNzQyMTAw/details – 220 N SET, HANDOUTS, VIDEO ... classroom.google.com E Open with Google Docs 2. The resultant of the force system shown is a 50-N · m counterclockwise couple. Find P, Q, and C. 4 3 > 3 m 2 m 2 m 3 4 20 N Page 1 I 2 - Q + Accredited: Accrediting Agency of Chartered Colleges and Universities of the Philippines (AACCUP) 80% A ENG 12:08 AM

pls show solution thank u8

Statics of Rigid Bodies (S5) Note: I will report you if you answer this post multiple times so please follow it.Thank you for understanding, Tutor! Content Covered: - Friction Direction: Solve the problem below by giving the complete solution. In return, I will give you a good and high rating. Thank you so much! Note: Be careful with the calculations in the problem. Kindly double check the solution and answer if there is a deficiency. And also, box the final answer. Thank you so much!

For my assigment, I was asked to design a electric motorbike that has a peformance equal to Honda CBR1000 Fireblade which has a petrol engine. A part of the the assignment is to calculate " An estimate of maximum Power your new motor will need to generate to match the Honda’s performance." I can make the assumption, apart from changing the motor, everything else is going to stay the same so the fairing,the rider and etc they're gonna be the same for the two bikes. So can you please tell me how I can calculate that which information would I need ?

You are assigned as the head of the engineering team to work on selecting the right-sized blower that will go on your new line of hybrid vehicles.The fan circulates the warm air on the inside of the windshield to stop condensation of water vapor and allow for maximum visibility during wintertime (see images). You have been provided with some info. and are asked to pick from the bottom table, the right model number(s) that will satisfy the requirement. Your car is equipped with a fan blower setting that allow you to choose between speeds 0, 1,2 and 3. Variation of the convection heat transfer coefficient is dependent upon multiple factors, including the size and the blower configuration.You can only use the following parameters:

The following exercises have been designed to engage you with the material presented in this module. They will further develop your understanding of key concepts, and completing them is a vital part of the learning process. 1. A centrifugal pump has the following characteristics: Q (m’h) 23 46 69 92 115 h (m) 17 16 13.5 10.5 6.6 2 n (%) 49.5 61 63.5 53 10 The pump is used to pump water from a low reservoir to a high reservoir through a total length of 800 m of pipe 15 cm diameter. The difference between the water levels in the reservoirs is 8 m. Neglecting all losses except friction and assuming f= 0.004, find the rate of flow between the reservoirs. Also determine the power input to the pump.

INSTRUCTIONS: Please write clearly and understandable way. Write all the corresponding Given with their corresponding symbols and units. Draw/Illustrate the diagram/circuit or drawings that is related to the problem, IF POSSIBLE, which is HIGHLY REQUIRED. Solve in step-by-step, no shortcut. Underline twice the Final Answer. PROBLEM: A hemispherical open tank used for concentration of sulfuric acid (Sp. Gravity=1.25) is filled up to the rim. If the tank gas a radius of 3 m, determine the work done in kilojoules after pumping the tank of all acid to another tank situated on a platform 3 m above the rim of the lower tank. A. 3,628.35 kJ B. 4,635.74 kJ C. 1,856.33 kJ D. 2,860.39 kJ

skating is an example of Select one: O rotating friction O slipping friction O Rolling friction O sliding friction

! SHOW FULL SOLUTION ! *DRAW FBD PLS *use DATA GIVEN PROPERLY thank you!

please send handwritten solution Q2 part a

Hello please solve showing each and every step in solution thanks

COMBUSTION ENGINEERING 1. The following details were noted in a test on a single-cylinder four-stroke oil engine: bore = 150 mm; stroke = 160 mm; speed of engine = 500 rpm; fuel consumption = 0.0475 kg/min; calorific value of fuel = 42,000 kJ/kg; the difference in tension on either side of the brake pulley = 400 N; brake circumference = 2.2 m; length of the indicator diagram = 50 mm; area of positive loop of indicator diagram = 475 mm2; area of negative loop = 25 mm?; spring constant = 0.8333 bar per mm. Calculate: a) The Brake Power in kW b) The Indicated power in kW c) The mechanical efficiency d) The Brake thermal efficiency, in percent kg e) The Brake Specific Fuel Consumption, bkW hr

COMBUSTION ENGINEERING 1. The following details were noted in a test on a single-cylinder four-stroke oil engine: bore = 150 mm; stroke = 160 mm; speed of engine = 500 rpm; fuel consumption = 0.0475 kg/min; calorific value of fuel = 42,000 kJ/kg; the difference in tension on either side of the brake pulley = 400 N; brake circumference = 2.2 m; length of the indicator diagram = 50 mm; area of positive loop of indicator diagram = 475 mm²; area of negative loop = 25 mm?; spring constant = 0.8333 bar per mm. Calculate: d) The Brake thermal efficiency, in percent kg e) The Brake Specific Fuel Consumption, bkW-hr

Tire manufacturers recommend that you check your tire pressure monthly to avoid unnecessary tire wear and enhance safety. This is best done when the tires are cold meaning; the car has not been driven for at least 2 hours. Since you leave for work before the sun comes up you decide to inflate your tires to the recommended pressure right after you get home from work in the afternoon when the tires are still warm. What would you find if you rechecked your tire pressure after the tires have cooled down? A.Tire pressure has decreased because there is a decrease in kinetic energy of themolecules resulting in more collisions with the inside walls of the tire thusincreasing the pressure inside the tire. B.Tire pressure has increased because there is a decrease in kinetic energy of the molecules resulting in fewer collisions with the inside walls of the tire thus decreasing the pressure inside the tire. C.Tire pressure has increased because there is an increase in kinetic energy of the…

Task 1 You are employed as a mechanical engineer within an unnamed research center, specializing in the development of innovative air conditioning systems. Your division is tasked with providing computer-based modeling and design solutions using computational fluid dynamics through ANSYS software. Your primary responsibilities involve the analysis of horizontal channel dynamics to meet specific criteria. Under the guidance of your immediate supervisor, you have been assigned unique responsibilities within an ongoing project. As a member of the research team, your role includes constructing an appropriate model and executing a sequence of simulation iterations to explore and enhance channel performance. Figure 1 provides a visualization of the horizontal channel under consideration. Consider 2D, incompressible, steady flow in a horizontal channel at a Reynolds number of 150. The schematic below illustrates the channel flow, not drawn to scale. For simplicity, neglect gravity. The…

27. You have the following compound machine. For S and ins a. What is the ideal mechanical advantage of this system? The inclined plane dimensions are 7.2 meters length and 1.8 meters height. What effort force is required to move the 600N create? In practice, you need to supply an effort force of 75 N to lift the crate. What is the efficiency? C. How could you redesign this compound d. machine so that the effort force needed was 50 N in practice? Assume the efficiency is your response from part C no matter what changes you make. Be specific with the changes you propose (if you add pulleys state how many, if you change the inclined plane dimensions state the new dimensions, etc.).

Project 2: In company that designs road cars and heavy trucks, it important to make the proper selection of the engines. Your part as a system energy engineer is to make a proper selection between an engine operates on Otto cycle/gasoline engine or Diesel cycle/diesel engine. Your head of department asked you to provide a detailed technical report that shows your selection for engine to be used with heavy truck vehicle. This is best achieved by performing the following tasks: Section.1: 1. Which engine does operate at lower ??? and has higher air-fuel mass ratio? 2. Which engine does burn fuel more completely? 3. Which engine has lower fuel cost? 4. Explain what compression ratio for Otto and Diesel cycles means 5. Explain what cut-off ratio for Diesel cycles means 6. Explain the limitations of SI engines in terms of their ability to operate at much higher compression ratios. What is this limitation called? 7. Provide general plot(s) for thermal efficiency, ? vs compression ratio, r…

Question 3 a) The details of travel time and capacity of different links in a portion of a city road network is as given in Table 1. Assign a traffic volume of 15,000 pcu per hr from node A to node I by multiple route assignment technique. Table 1: Travel time and capacity Link Travel time in minutes Practical capacity in pcu/hr A-B 6000 A-C 5000 A-D 5000 B-F 6000 C-E 5000 D-G 5000 E-H 5000 F-I 6000 G-H 5000 H-I 10000 wwNN 2 2 3 3 3 2 N33 N 2 2

A suspended date that's able to pivot from the top seperates two liquids. There is a stopper that prevents the gate opening anti-clockwise. The gate has a height of 0.5m. The liquid on the right is twice as dense as the liquid on the left. The liquid on the left has a depth of 0.3m. 1) What is the minimum depth of liquid on the right for the gate to open. 2) Comment on the ability to solve this question if the liquid on the left was 1m (filled to the top)

0 Cisco Webex Meetings O Meeting Info Hide Menu Bar A 55:47 O 0 - O x Eile Edit ShareView Audio & Video Participant Meeting Help O Layout VIDHYA NAIR Vishnu Deepak YENDURI SANKEERTH Ashesh Saha SAYOOJ RS AKSHANSH CHOUDHARY AADHIL N Me Host Class 11 18.01.2022 Equivalent Force Systems.notPoweaint Ink Tool Viewing Ashesh Saha's screen hat you want to do. A A Share File Home Insert Design Tansitions Animations Slide Show Thickness Pen Highlighter Eraser Lasso Select • Select Objects Convert Stop to Shapes Inking Write Pens Ink Art Close Example 39: Replace the three forces shown in Fig. below, acting on the plate by a wrench. Specify the magnitude of the force and couple moment for the wrench and the point P(x,y) where its line of action intersects the plate. s00I N 300j N 9 10 Side S of 10 0B English India Notes Comments 12:01 P Type here to search 31°C Ao -a 00 ENG 18-01-2022 8 Unmute v O Start video O Share & Participants O Chat ... --. O L O M0 12:01 PM !- a 4) ENG 1/18/2022

Question 20 of 20 < A Water Balloon Battle. You are launching water balloons at a rival team using a large slingshot. The other team is set up on the opposite side of a flat-topped building that is 30.0 ft tall and 50.0 ft wide. Your reconnaissance team has reported that the opposition is set up 10.0 m from the wall of the building. Your balloon launcher is calibrated for launch speeds that can reach as high as 100 mph at angles between 0 and 85.0° from the horizontal. Since a direct shot is not possible (the opposing team is on the opposite side of the building), you plan to splash the other team by making a balloon explode on the ground near them. If your launcher is located 55.0 m from the building (opposite side as the opposing team), what should your launch velocity be ((a) magnitude and (b) direction) to land a balloon 5.0 meters beyond the opposing team with maximum impact (i.e. maximum vertical speed)? (a) Number i (b) Number i Units Units UNITS CHOICES: no units, degrees, s,…

Question 29 Not yet an A pulley, starting from rest, is given an acceleration of 0.5 rad/s.What will be its speed in r.p.m. at the end of 2 minutes? If it is uniformly retarded at the rate of 0.3 rad /s, in how many minutes the pulley will come to rest? B Enter your answer here.... hp

1) A low-friction cart is placed between two identical springs attached to rigid walls. If you push the cart against one of the springs and release it, it will continue to move back and forth between the springs. www Draw a force-time graph showing the sum of the horizontal forces exerted on the cart as it moves back and force between the springs. Scientific Abilities Is able to construct a force diagram Missing No representation is constructed. Inadequate FD is constructed but contains major errors such as incorrect mislabeled or not labeled force vectors, length of vectors, wrong direction, extra incorrect vectors are added, or vectors are missing. Needs Improvement FD contains no errors in vectors but lacks a key feature such as labels of forces with two subscripts or vectors are not drawn from single point, or axes are missing. Adequate The diagram contains no errors and each force is labeled so that it is clearly understood what each force represents. Explain whether or not this…