Water at
To Calculate:
The pressure at B.
Answer to Problem 11.1PP
Pressure at B:
Explanation of Solution
Point A at tank surface:
Where,
Want to see more full solutions like this?
Chapter 11 Solutions
Applied Fluid Mechanics (7th Edition)
Additional Engineering Textbook Solutions
Engineering Mechanics: Dynamics (14th Edition)
Engineering Mechanics: Statics & Dynamics (14th Edition)
Mechanics of Materials (10th Edition)
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Statics and Mechanics of Materials (5th Edition)
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
- A water jet with a flow rate of 2.83 m3 / s is traveling at 6 m / s in the positive x direction. The cost of the current striking a stationary splitter is correct about a 45 aç angle, other company are deflected downwards by the same angle and the final velocities of the two streams are 6 m / s. By neglecting the gravity, the separator is in place against the force applied by the water. calculate the x- and z- power of what is required to hold it. For water ? = 1.184 kg / m3arrow_forwardA pump at an elevation of 300m is pumping 0.05 m³/s of water through 2.4 km of 150-mm pipe to a reservoir whose level is at an elevation of 380m. What pressure will be found in the pipe at a point where the elevation is 335m above the datum and the distance (measured along the pipe) from the pipe is 970m? Compute the capacity of the pump. Use E/D= 1.5384x10-³arrow_forwardThe plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.1. Find the maximum allowable speed to operate the pumparrow_forward
- A Pelton wheel has a tangential velocity of buckets of 15 meters/sec. the water is being supplied under a head of 36 meter at the rate of 20 liters/sec. the buckets deflected jet through an angle of 1600. if the coefficient of velocity for nozzle is 0.98. find the power produced by the wheel.arrow_forwardWater at a guage pressure of 4 kPa flows at a rate of 250 l/s in a 135° pipe bend of diameter 300 mm, find in MN the magnitude and direction of the resultant force on the bend.arrow_forwardThe figure below shows a gasoline storage tank with cross-sectional area Asub1, filled to a depth h. The space above the gasoline contains air at pressure psub0, and the gasoline flows out the bottom of the tank through a short pipe with cross-sectional area Asub2. Derive expressions for the flow speed in the pipe and the volume flow rate. Thank you!arrow_forward
- A centrifugal pump delivers water at a rate of 0.03 m /sec to a height of 18 meters through a pipe of 100 mm dlameter and 90 m long. If the overall efficiency of the pump is 75 %, find the power required to drive t e pump. (Take f 0.012).arrow_forwardThe plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis. 3.1 Find the maximum allowable speed to operate the pump 3.2 What power is expected in overcoming friction at this speed, takef = 0.01arrow_forwardA centrifugal pump is used to pump water (1000 kg/m³) to a height of 10m, the water splashes down back into the tank. The diameter of the impeller of the pump is 145 mm, the pump speed is 2900 rpm. The equation to calculate the flow V in the valve depending on the pressure drop differential pressure (dp) in the valve isV = 4 * sqrt (dp), whereas V is in m³/h and dp in bar. Please estimate the water flow.arrow_forward
- 2. A pump driven by an electrical motor moves 25 gallons per minute of water from a reservoir A to B, lifting the water to a head of 245 ft. The efficiency of the pump is 65%. Neglecting velocity head, friction head and minor losses; What power input in horse power is required?arrow_forwardAn irrigation pump delivers water through a 6 - inches horizontal pipe flowing full at the outlet, the jet striking the ground at a horizontal distance of 12 ft and a vertical distance of 4 ft from the end of the pipe. Find the capacity of the pump in gallons per minute.arrow_forward6.7. Calculate the force exerted by the water on this orifice plate. Assume that water in the jet between orifice plate and vena contracta weighs 4.0 lb. 0.75 0.20 10' darrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY