You are presented with the following controlled rectifier configurations: |Configuration Topology Supply phase voltage Load resistance Load inductance (line to neutral) (Ohm) (Henry) |Single phase half-wave Single-phase bridge Three-phase half-wave Three-phase bridge Six-phase half-wave Vs 100 Vs Vs 100 3 100 4. Vs 100 Vs 100 infinite Assume no commutation diodes are used. State the smallest firing delay angle that will effect discontinuous current flow in the load for, 8. Configuration 4; 9. Configuration 5;

You are presented with the following controlled rectifier configurations: |Configuration Topology Supply phase voltage Load resistance Load inductance (line to neutral) (Ohm) (Henry) |Single phase half-wave Single-phase bridge Three-phase half-wave Three-phase bridge Six-phase half-wave Vs 100 Vs Vs 100 3 100 4. Vs 100 Vs 100 infinite Assume no commutation diodes are used. State the smallest firing delay angle that will effect discontinuous current flow in the load for, 8. Configuration 4; 9. Configuration 5;

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
How is a solid-state diode tested? Explain.
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
Draw vx and v0 according to the input voltages in the circuit shown in the figure. note = R1 = 10Kohm R2 = 1kohm R3 = 1Kohm, the threshold voltages of diodes will be VE = 0.7V.
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V. V1=5 V and V2=9 V. R www D1 Vin Vout v1 V2 Maximum voltage of output waveform Minimum voltage of output waveform
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V, V1=4 V and V2=10 V. R www DZ D1 Vin Vout vi V2 Maximum voltage of output waveform Minimum voltage of output waveform
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
In the circuit shown in the figure; A) When RL = 5Kohm and capacitor C is switched on, draw VA and V0 in scale according to input voltage Vs. NOTE = diodes are ideal
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V, V1=3 V and V2=8 V. R www D2 DI Vin Vout V2 Maximum voltage of output waveform Minimum voltage of output waveform
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
The three-phase circuit shown in figure 1 is 220 Vrms per phase and 50Hz. Diodes are real. The circuit produces an output shown in Figure 2. Indicate the conduction angle of diode D5. What times does this conduction correspond to? Use the first cycle only (0-360°). to-0 sec.