Which of the following does represent the state equations A(t +1) and B(t+1) in terms of A, B and x the following sequential circuit? A Clk -A' D -B Clk -B' Clock Select one: O A(t+1)=B+B'x'=B+x' & B(t+1)=Ax+B°x' O A(t+1)=B(B'+x')=Bx' & B(t+1)=(B'+x)(A+x) O A(t+1)=B+B'x'=B+x' & B(t+1)=(B'+x)(A+x) O A(t+1)=A'+B'+x' & B(t+1)=Ax+B'+x' O A(t+1)=A'B'x' & B(t+1)=Ax+B'x'

Which of the following does represent the state equations A(t +1) and B(t+1) in terms of A, B and x the following sequential circuit? A Clk -A' D -B Clk -B' Clock Select one: O A(t+1)=B+B'x'=B+x' & B(t+1)=Ax+B°x' O A(t+1)=B(B'+x')=Bx' & B(t+1)=(B'+x)(A+x) O A(t+1)=B+B'x'=B+x' & B(t+1)=(B'+x)(A+x) O A(t+1)=A'+B'+x' & B(t+1)=Ax+B'+x' O A(t+1)=A'B'x' & B(t+1)=Ax+B'x'

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter35: Harmonics 916

Section: Chapter Questions

Problem 2RQ: Which of the following are considered triplen harmonics: 3rd, 6th, 9th, 12th, 15th, and 18 th?

See similar textbooks

Similar questions

A signal x(t) is known to be sinusoidal with frequency 100 Hz. It is sampled by an A/D converter, and thefollowing two sequential values are observed: x(0.001) = 10, x(0.002) = 7. Determine the value of x(0.003).
| sketeh out the follewing signals: (a=5, b=3, c=2) a-) V = 15a(sin21000*ct) b-) V = 3b(cos(r500*ct)+3) c-) Assume that you measure the signal V1 using Digital Volt Meter(DVM) and ossiloscope. What will you read on the DVM display and oscilloscop dispaly when the input voltages are defined as 1-) V = 15a(sin2m1000*ct) 2-) V = 3b(cos(7500*ct)+3) Write down and sketch all the voltages for each case. Show all parameters, including period and maximum values of the signals. aR V AC aR V, aR What will you read at the DVM display when you read the voltages at AC mode What will you read at the DVM display when you read the voltages at DC range
A series R-C circuit consists of a resistor of 700 02, time constant of 28 msec. The value of capacitor in the circuit will be equal to UF a. 0.025 O b. 20 O c. 40 O d. 19.6
5) Perform the following function in a simple program steps a) BL-5.BH b) DX = AX + BX O CX
The number of loops in the following signal flow graph is G, R G2 no one of these five seven three six eight four
I want to confirm if my work is correct. The problem is: For the Astable Multivibrator shown in the figure, take RA=1k, RB=0.5k and C=1microF and calculate the duty cycle and the frequency of the pulse that is generated. Note that you can calculate the frequency from 1/T. I've attached the figure and my work below. The formulas I used is the ones that were provided.
How many infinite zeros and finite poles has the following open-loop system? 28 - s- 17 s(11 + sT1)(3 – sT2) G(s) = O A) Three poles and two zeros One zero and four poles B) Two poles and one zero Three zeros and four poles O D) E) Four poles and four zeros
For the circuit below with input voltage V1, a step function of magnitude 25 volts at time t-0, find the transient response voltage across the capacitor C1 and plot the results: (Provide your calculations and reasoning for your answer.) R1 555 250mH V1 = 0 V2 - 25 TD = 0 TR In V1 C1 TF in PW- 25 PER = 3.3u
Problem 1: Add following two signals:V1(t) = 6sin(wt)V2(t) = 18cos(wt)Write your answer in-terms of +cosine as well as +sin signals. Also identify which signals leads/lags to which signal and write all four possible answers
DIFFERENCE EQUATION ( NEED ONLY HANDWRITTEN SOLUTION PLEASE OTHERWISE DOWNVOTE)
An inductor with L = 150mH and r = 200(Omega) is in series with a capacitor, a resistor, and a generator of w = 1000 rad / s The voltage across the inductor Vind is measured to be 10.87 V, VR is measured to be 4.65 , and Vc is measured to be 5.96 V. What is the generator voltage V? (Hint: This is the measurement to be performed in this laboratory for LCR circuits. Use the appropriate equations to find VL and Vr' and then use them and the values of VR and VC to calculate V.)
At t=0 S switch is closed. Initially the capacitor was uncharged. What is the steady state value of the input current in in Ampere? Parameters: R₁ = 30, R₂ = 4N, R3 = 4N, U = 9 V, C = 20μF. S iin R1 R3 ULO Answer: R₂ C=