What is the value of the torsion constant for the beam cross section shown below? 60 mm 20 mm 20 mm 20 mm a mm The value of a is 108 mm. All parts have a thickness of 1.0 mm apart from the lower horizontal part which has a thickness of 2.2 mm. Enter your answer as an integer, in mm", but without any units. You have an error margin of 3%

What is the value of the torsion constant for the beam cross section shown below? 60 mm 20 mm 20 mm 20 mm a mm The value of a is 108 mm. All parts have a thickness of 1.0 mm apart from the lower horizontal part which has a thickness of 2.2 mm. Enter your answer as an integer, in mm", but without any units. You have an error margin of 3%

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A tapered circular rod of diameter varying from 20 mm to 10 mm is connected to another uniform circular rod of diameter 10 mm as shown in the following figure. Both bars are made of same material with the modulus of elasticity, E = 2×105 MPa. When subjected to a load P = 30T kN, the deflection at point A is_ mm. 20mm 2m d, 10 mm 1.5m P 30nkN
Deflection Given: the beam cross-section shown have the following cross-sectional properties f'c = 4000 psi n = 8 Find Instantaneous Deflection.
Subject: Strength of Materials Topic: Beam Deflections Find y at point B. Note: y=deflection
A tapered circular rod of diameter varying from 20 mm to 10 mm is connected to another uniform circular rod of diameter 10 mm as shown in the following figure. Both bars are made of with modulus of same material elasticity, E =2×10 subjected to a load P=30r kN, the deflection at point A is MPа. When %3D mm. [2 Marks] d, = 20 mm 2 m B d, =10 mm %3D 1.5 m P = 30 t kN
This is an exercise to illustrate the effects of mesh refinement on a 1-d rod. To estimate the self-weight elongation (8) of the tapered conical rod shown in the figure. The diameter varies linearly from Do at the bottom to aDo at the top, where 0.1 < E Young's Modulus y Unit weight (Diameter at top) 8 clongation D (Diameter at bottom) a<0.5. Solve for L= 5m, y= unit weight of steel, E= young's modulus of steel, Do=3m and a=0.3. Solve the problem at least four times using an increasing number of rod elements (nels=2, 4, 6, 8). Make appropriate assumptions about how to deal with the changing cross-sectional area and self-weight loading along the length of the rod. A plot of the dimensionless tip deflection SE/yL? vs. number of elements (nels) used in the discretization to show convergence on the exact solu- tions of
Suppose we have a uniform beam that is 3.73 metres long has a flexural rigidity of 34301 Nm². N Find the deflection of the beam in millimetres if the beam is under a uniform load of 86. with your answers. and is supported with simple supports at both ends. Fill out the table below m x-coordinate x = 0.22 x = 1.38 x = 2.05 Deflection (mm) y(x) = Skipped y(x) = Skipped y(x) = [Skipped x = 2.98 y(x) = [Skipped x = 3.58 y(x) = Skipped Enter as many decimal places as your calculator allows (8 to 10). Your answer must be within ±0.0005 of the correct answer to be considered correct.
don't answer the X figure, just answer the d and e
The net area in tension, Ant, of the L6 x 6x 3/8 angle shown in the figure is equal to:
5) In the section of the figure below, 6 rebars 36 are used as tensile steel and 4 rebars number 20 are used as compressive steels. Assuming d' is 60 mm and fy is 400 MPa, calculate the anchor of the ultimate cross-sectional strength. 800mm 150mm 750mm 700mm O O 300mm (If there is a lack of problem information for the numerical solution section, make a logical assumption and write it down) The answer must be typed, avoid handwriting. The answer should be short and completely correct, l give a negative score to the answer that I feel is wrong; so please be careful, thank you.
The 16 x 22 x 25-mm rubber blocks shown are used in a double U shear mount to isolate the vibration of a machine from its supports. An applied load of P = 238 N causes the upper frame to be deflected downward by 4 mm. Determine the shear modulus G of the rubber blocks. Double U anti-vibration shear mount 25 Rubber block dimensions Shear deformation of blocks O 0.745 MPa O 0.883 MPa O 1.140 MPa
Consider the beam with loading as shown in the figure below. The deflection of the beam at midspan is a wɔlª What is the value of -? Round off your answer to b EI a two decimal places. w w A B
The figure shows a cutaway view of an assembly in which a solid bronze [G = 6,500 ksi] rod (1) is fitted inside of an aluminum alloy [G = 4,000 ksi] tube (2). The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at A. The rod diameter is d1 = 2.05 in. The outside diameter of the tube is D2 = 2.8 in. and its wall thickness is t2 = 0.110 in. Overall dimensions of the assembly are a = 55 in. and b = 11 in. The allowable shear stresses for the bronze and aluminum materials are 10800 psi and 7800 psi, respectively. Further, the rotation angle of end B must be limited to a magnitude of 4.8°. Based on these constraints, what is the maximum torque TB that can be applied at end B?