What are the x, y values for the following prismatic part?R0.251.5001.500 1.5004.0002.000 1.000Y1.0002.00X6.000·00.5General tolerance 0.020All dimensions in inchesR0.500

Therefore , the detailed calculation yields : x=275y=150So, the x and y values are indeed 275 and…

Answered: What are the x, y values for the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine larger diameter, for the figure below. All dimensions are in mm) 110.916 e 040 091 S 100.916 108.517 mm 120.916 mm 110.916 mm cant be determined 130.916 mm DR 40
On the toleranced rectangle below, state the tolerance within which the top surface must be flat. 1.000 1.010 1.010 1.000 There is no tolerance within which the top surface must be flat O .010
What is the worst-case distance between the bottom surface of the slot and the bottom surface of the part in the drawing below? B 4.000-4.020 1.475 O 1.030 2.950 B 4.00 O 1.450 O 1.500 1.000-1.010 .010M ABM 2.00 A
Build the following part. Report the mass in pounds. Assume all dimensions are in inches. The material is Vanadium. (Located in the "Other Metals" folder in the material properties.) A = 1.72 B = 1.4 2.40 1.20 T .75 TYP 1.20 TYP .70 -1.00 TYP A A A+3.25 R.35 TYP -R.65 TYP CBORE FOR 5/16 HEX HEAD BOLT Ø.332 THRU ALL LØ813 V 235 .10- SECTION A-A 23. B B+1
Round number to three significant figures. 1.548937 x 10^7
Build the following part and report the volume in units cubed. A = 48 B = 51 R20 R10 B 30 50 2X R10 R20 Ø20 A 10 TYP DESIGN ERICS DRAWING TITLE
On the toleranced rectangle below, what is the tolerance within which the top surface must be parallel to the bottom surface? 0.002 O .002 1.015 1.000 O There is no tolerance within which the top surface must be parallel to the bottom surface O .015
Two identical cubes which are machined to 1.000 +/- 0.005 inch, are glued together. Glue thickness is 0.01 inch. Find the dimension of the opening of a box used to store the assembly of two cubes. Given the 28. allowance between the box and the cubes is 0.02 inch, the tolerance on the opening is 0.01 inch.
Tolerance Table All dimensions in inches 15.00 + 0.25 11.0 + 0.4 3.1 X.X +0.1 3.100 X.XX +0.05 Х.XXX +0.001 All units in cm All units in cm All units in inches Calculate the nominal, minimum, and maximum height (in cm) of the three-cube stack shown at right. The cubes are stacked atop each other with no gaps between them. Pay special attention to units, and note that 1 inch equals 2.54 cm. C Hints: ??? • For each cube, calculate the nominal, minimum, and maximum height using the nominal heights and tolerances provided in the three drawings. Ensure that the cubes' heights and tolerances are all in the same units before adding them in the next step. • Add the three nominal heights to find the nominal height of the stacked cubes. • Do the same for the three minimum heights and three maximum heights. • The tolerance table for cube C does not apply to the drawings for cubes A or B. Show all your work. 1. Nominal height = cm %3D 2. Minimum height = cm %3D 3. Maximum height cm
What is the worst-case distance between the bottom surface of the slot and the bottom surface of the part in the drawing below? B 4.000-4.020 O 1.475 O 1.450 O 2.950 O 1.500 O 1.030 4.00 0.010MABM 1.000-1.010 2.00 A
Calculate the Minimum Y distance on the drawing below: 1.000 O 2.000 O .460 O .510 1.966 O .500 C 2.000 Ø.995-1.000 6.00 0.008 MABC 3.000 Y 01.005-1.030 +0.005MABC B A .XX = .01 ANGLES= ± 1°
Question 1 a) Calculate the following slip gauges assemble to 100.115 mm. Use the increment of 1st, 2nd, 3nd & 4th to give the total assemble of 100.115mm. NB. Use the table below. Size or Range Increment No. of Pieces 1.005 1.001-1.009 1.01 1.49 0.5-9.5 10-100 0.001 0.01 49 0.5 19 10 10

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

What are the x, y values for the following prismatic part? R0.25 1.500 1.500 1.500 4.000 2.000 1.000 Y 1.000 2.00 X 6.000· 00.5 General tolerance 0.020 All dimensions in inches R0.500