Water at 20 °C flows through the pump impeller shown in the figure below, where the inner and outer diameters of the impeller are 160 mm and 400 mm, respectively, and the width of the pump blades is 55 mm. Part A μA Blade Estimate the shaft power required to drive the pump at this operating condition. Express your answer to three significant figures and include appropriate units. W shaft = Value Pump impeller Units The impeller rotates at 3600 rpm. Under a particular operating condition, water enters in a direction normal to the inflow surface, the component of the outflow velocity normal to the outflow surface, Vr, is equal to 19 m/s, and the magnitude of the absolute velocity, V, at the outflow surface is 33 m/s. Outflow surface Inflow surface 4 160 mm ✓ 400 mm

Water at 20 °C flows through the pump impeller shown in the figure below, where the inner and outer diameters of the impeller are 160 mm and 400 mm, respectively, and the width of the pump blades is 55 mm. Part A μA Blade Estimate the shaft power required to drive the pump at this operating condition. Express your answer to three significant figures and include appropriate units. W shaft = Value Pump impeller Units The impeller rotates at 3600 rpm. Under a particular operating condition, water enters in a direction normal to the inflow surface, the component of the outflow velocity normal to the outflow surface, Vr, is equal to 19 m/s, and the magnitude of the absolute velocity, V, at the outflow surface is 33 m/s. Outflow surface Inflow surface 4 160 mm ✓ 400 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water at 20"C Bows through the pump impeller shown in the figure below, where the inner and outer diameters of the impeller are 160 mm and 400 mm respectively, and the width of the pump blades is 55 mm Part A Wan- μA Estimate the shaft power required to drive the pump at this operating condition Express your answer to three significant figures and include appropriate units. Value Blade Pump impeller The impeller rotates at 3600 rpm Under a particular operating condition, water enters in a direction normal to the inflow surface, the component of the outflow velocity normal to the outflow surface. V is equal to 17 m/s, and the magnitude of the absolute velocity, V, at the outflow surface is 33 m/s Submit Request Answer Units Outflow surface Inflow surface ? 160 บท 400 mun
A prototype pump is designed to so that the attached dimensionless performance curves apply. (a) If the pump is powered by a fixed speed motor delivering a rotational speed of 400 rpm and the impeller diameter is 2 m find the unknown quantities (Q, H, P,n ). Assume the pump is operating a peak efficiency and is pumping cold water. (b) If the pump is to be connected to standard steel pipe, which pipe should be used. Сн 1.00 Efficiency-n 0.75 CH 3 0.50 0.25 0.04 0.08 0.12 0.16 Ce C, and Efficiency
Example 4: If the diameter at section 1 is D₁ = 0.5 m, and at section 2 the diameter D₂ = 0.2 m. All the other conditions are the same as in Exercise #3. What power in kilowatts and in horsepower must be supplied to the flow by the pump? Assume h₁ = 3 m of water and a₁ = α₂ = 1. Water is being pumped through a system. D₁ = 0.5 m Z₁ = 30 m P₁ = 70 kPa gage α₁ = 1.0 1 Pump Sual Z₂ = 40 m P2 = 350 kPa gage %₂ = 1.0 D₂ = 0.2 m Head loss in pipe = 3 m Water Q = 0.5 m³/s Properties: Water (10°C, 1 atm, Table A.5): y = 9810 N/m³
6.1 D, and D, are the inlet and outlet diameters of the pipe connected to the water turbine shown in the figure. The gage pressure at the inlet and outlet of the turbine are p, and p2. The elevation difference between the pipe inlet and outlet is h. If the water flow rate is Q and the total frictional losses is H1. Determine the mechanical power delivered by the turbine if it is 90% efficient. D; Turbine, D2 Dj = 320 mm D2 = 160 mmn h= 45m P1 =10.5bar P2 =5.5 bar Q = 0.065 m³.sl HL =8.0 m
Given: diameter of pipe in point 1 = 3.9indiameter of pipe in point 2 = 2.5inspecific gravity of the liquid = 0.79h(ft) = 0.60ftpressure at point 1 = 14.6 psiapressure at point 2 = 49 psiapump and motor efficiency = 66%diameter of pipe in point 4 = 4.5indiameter of pipe in point 5 = 2.3 inZ3 = 35ft With the schematic diagram of a pump, tanks, and piping determine the following:1) The velocity of the liquid at point 2 (ft/s)2) Pump work used by the liquid (Wpump U) (hp)3) Electric motor power in out (kW)4) In figure 3, the shaded (pink) in the U tube is mercury; determine y. specific gravity of mercury 13.75) Mass flow rate
* A hydraulic lift raises a total load of 8 tonnes through a height of 12 m- once in every two minutes. The speed of the lift being 60m/sec. It is worked from an accumulator, which is being continuously charged by a pump. The pressure of water is 35 Kg/cm3. Neglecting friction losses in the pipe. Power required to drive the pump= 12.6 hp True O False O
A water pump produces a flow of 0.25 m /s and a power of 2 kW, using an 300-mm-diameter impeller. Part A What is the flow if a 150-mm-diameter impeller is used to maintain dynamic similitude? Express your answer to three significant figures and include the appropriate units. Part B What is the power if a 150-mm-diameter impeller is used to maintain dynamic similitude? Express your answer to three significant figures and include the appropriate units.
3. A pump is located 4.5 m to one side of, and 3.5 m above a reservoir. The pump is designed for a flow rate of 6 L/s. For satisfactory operation, the static pressure at the pump inlet must not be lower than 26 m of water gage. Determine the smallest standard commercial steel pipe that will give the required performance. 4.5 mm- Pump -Q = 6 L/s 90°- elbows 3.5 m Water 5°C
A water pump produces a flow of 8 ft /s and a power of 4 hp, using an 11-in.-diameter impeller. Part A What is the flow if a 6-in.-diameter impeller is used to maintain dynamic similitude? Express your answer using three significant figures. Q = ft /s Part B What is the power if a 6-in.-diameter impeller is used to maintain dynamic similitude? Express your answer using three significant figures. hp
The bore and stroke of an air compressor are 276mm and 164mm, respectively. If the piston displacement is 0.049m3/sec, what is the operating speed of the compressor?
Q1/ A45 reducing bend is connected in apipe line, the diameters at the inlet and outlet of the bend being 600mm and 300mm respectively find the force exerted by water on the bend if the intensity of pressure at inlet to bend is 8.829 N/cm² and rate of flow of water is 600 liter /s. Lx P₁A₁
Problem-4: The characteristics for a pump are given in the table below. The pump is required to left water against static head Az = EN" m. The pipe arrangement has a total length L the pump discharge, head, efficiency and power for the given pipe system. 200, d = 0.1 m and f= 0.016. Find %3D Q (L/s) 10 20 30 35 42 50 Hp (m) efficiency % 210 201 180 150 129 93 48 30 58 80 85 86 74 EN=62 Hp = Az + h, = Az + 12.1 d P = 757