Water at 10C temperature flowing from a pipe with a diameter of 100mm at a speed of 2m / s, air from a pressure of 2 ATM at 180F flowing at a speed of 50 ft / s from a pipe with a diameter of 2 in, and an oil with a specific gravity of 0.78 and a diameter of 20 cp at a speed of 5 ft / s through a 2in pipe. Shows the flow state of the biopolymer melt flowing through the pipeline at a speed of 0.2 m/s, with a density of 900 kg/m3 and a density of 1 Pa-s

Water at 10C temperature flowing from a pipe with a diameter of 100mm at a speed of 2m / s, air from a pressure of 2 ATM at 180F flowing at a speed of 50 ft / s from a pipe with a diameter of 2 in, and an oil with a specific gravity of 0.78 and a diameter of 20 cp at a speed of 5 ft / s through a 2in pipe. Shows the flow state of the biopolymer melt flowing through the pipeline at a speed of 0.2 m/s, with a density of 900 kg/m3 and a density of 1 Pa-s

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.15P

See similar textbooks

Similar questions

Ethylene glycol with a mass flow rate of 0.01 kg / sec flows in a thin-walled pipe with a diameter of 3 mm. The pipe is in the form of a serpentine, and was lifted into a well-mixed water bath at 25 ° C. Calculate the heat transfer and pipe length required for the fluid to enter the pipe at 85 ° C and exit at 35 ° C?
A certain gas was produced as a product of a decomposition reaction in a reactor vessel. The reaction generated a certain amount of force that allowed the gas to move at 35 m/s. The diatomic product gas (gamma = 1.36) will be transported adiabatically in a commercial steel pipe with a diameter of 1 inch. If the exit of the reactor and start of the pipe has a same pressure of 6 atm abs. and temperature of 120 degrees Celsius. The molecular weight of the gas is 70.91 kg/kgmol. 2. What is the Mach No. at the entry of the pipe? 0.36 0.41 0.14 none of the given 0.25 0.52 0.63
The liquid food is flowed through an uninsulated pipe at 90 ° C. The product flow rate is 0.4 kg / s and has a density of 1000 kg / m³, specific heat 4 kJ / (kg K), a viscosity of 8 x 10-6 Pa s, and a thermal conductivity of 0.55 W / (m) K). Assume that the change in viscosity is negligible. The internal diameter of the pipe is 20 mm with a thickness of 3 mm made of stainless steel (k = 15 W / [m ° C]). The outside temperature is 15 ° C. If the outer convective heat transfer coefficient is 18 W / (m² K), calculate the heat loss at steady state per meter of pipe length. a.Find the convection coefficient in the pipe = AnswerW / m² ° C. b. Calculate heat loss per meter pipe length = Answerwatt.
If Xf = 42000 ppm, Xb= 70000 ppm, and Md= 1 kg/s then the mass flow rate of the brine is إختر أحد الخيارات: kg/s 2.5 .a O kg/s 1.5 .b O kg/s 1.2 .C O kg/s 1 .d O
The liquid food is flowed through an uninsulated pipe at 90 ° C. The product flow rate is 0.3 kg / s and has a density of 1000 kg / m³, specific heat 4 kJ / (kg K), a viscosity of 8 x 10-6 Pa s, and a thermal conductivity of 0.55 W / (m) K). Assume that the change in viscosity is negligible. The internal diameter of the pipe is 30 mm with a thickness of 3 mm made of stainless steel (k = 15 W / [m ° C]). The outside temperature is 15 ° C. If the outer convective heat transfer coefficient is 18 W / (m² K), calculate the heat loss at steady state per meter pipe length. a. Find the convection coefficient in pipe = W / m² ° C. b. Calculate heat loss per meter pipe length = watts
The liquid food is flowed through an uninsulated pipe at 90 ° C. The product flow rate is 0.3 kg / s and has a density of 1000 kg / m³, specific heat 4 kJ / (kg K), a viscosity of 8 x 10-6 Pa s, and a thermal conductivity of 0.55 W / (m) K). Assume that the change in viscosity is negligible. The internal diameter of the pipe is 30 mm with a thickness of 3 mm made of stainless steel (k = 15 W / [m ° C]). The outside temperature is 15 ° C. If the outer convective heat transfer coefficient is 18 W / (m² K), calculate the heat loss at steady state per meter pipe length. a. Find the convection coefficient in the pipe = Answer W / m² ° C. b. Calculate heat loss per meter pipe length = Answer watt.
2 m^3/min of a light oil are to be heated from 20C to 100C (with zero vaporization) in an exchanger using 250 kPa steam of 90% quality. The heat losses to the surrounding air have been estimated to be 5% of the heat transferred from the condensing steam to the oil. If the steam condensate leaves at its saturation point, what mass of steam perhour will be used in the exchanger? For light oil, Specific gravity= 0.88Specific heat= 2.00 kJ/kg-KFor steam at 250 kPa,Saturated liquid: hf= 535.49 kJ/kgvf=0.001067 m^3/kgSaturated vapor: hg= 2716.8 kJ/kgvg= 0.7188 m^3/kg
High-pressure steam condenses at 400 K on the outer surface of a thin-walled tube of 50 mm diameter. The overall heat transfer coefficient between steam and air on the inside of the tube is 200 W/m?. If the air enters the tube at 25 m/s, 150 kPa and 280 K, find the length of the tube required for the air to be heated to 350 K. [Ans. L = 13.9 m]
• Water evaporates from the surface of a pond and the vapour diffuses through the stagnant film of air of thickness 3 mm. Water temperature is 23°C and the air temperature is 27°C. Relative humidity of air is 65%. Average diffusivity is 0.2595 cm²/s. What is the average flux of evaporation? Antoine equation constants A=13.8573 B=5160.2
Conduction 1. A thermodynamic analysis of a proposed Brayton cycle gas turbine yields P= 5 MW of net power production. The compressor, at an average temperature of T. = 400°C, is driven by the turbine at an average temperature of T₁ = 1000°C by way of an L = 1m-long, d= 70mm - diameter shaft of thermal conductivity k = 40 W/m K. Compressor min T Combustion chamber Shaft L Turbine Th out (a) Compare the steady-state conduction rate through the shaft connecting the hot turbine to the warm compressor to the net power predicted by the thermodynamics- based analysis. (b) A research team proposes to scale down the gas turbine of part (a), keeping all dimensions in the same proportions. The team assumes that the same hot and cold temperatures exist as in part (a) and that the net power output of the gas turbine is proportional to the overall volume of the device. Plot the ratio of the conduction through the shaft to the net power output of the turbine over the range 0.005 m s Ls 1 m. Is a…
(heat transfer ) thanks The velocity of the fluid flowing in parallel over a 500mmx500mm flat heater surface is U= 19 m/s and the inlet velocity temperature is T_∞15 C. The surface temperature of this plate is T_s140 C, the friction force is F_D=0.4 N and the surface area of the plate is A=0.32 m2. According to this;(F_D= 0.4N A=32 m2)a) Surface shear stressb) Find the coefficient of frictionc) Heat transfer coefficientd) What is the amount of heat transfer (electric power) that must be given to maintain a constant surface temperature?
Design a hydrocooling unit to cool down fruits and vegetables from 30 °C to 5 °C in 20 minutes at a rate of 20,000 kg of fruit or vegetables/h. The design must fulfill the following requirements: The unit will be an immersion flooded system. It must be able to cool down and transport the products in chill water. The tank has the following dimensions approximate. three meters wide and up to 90 cm hight. The water will circulate and be cooled through the evaporation section of a refrigeration system. The refrigerant temperature inside the coils will be -2 °C, and the water temperature must not drop below 1 °C and must not exceed 6 °C. Assuming reasonable values for the average density, specific heat, and porosity of the product (the fraction of the volume of air in a box), recommend reasonable values for: The speed of the water through the canal, the capacity of the cooling system. the compressor power.