voltage divider of 50 ohms is connected across a 100 V DC source. A load resistance of 10 ohms is connected across a tap in the potential divider and the negative of the source. If a current of 4 A flows towards the load, what is the current supplied by the source? (Remember, a voltage divider is a network of resistors that are connected in series the purpose of which is to divide a voltage into each of the resistors.) Show complete solution.

voltage divider of 50 ohms is connected across a 100 V DC source. A load resistance of 10 ohms is connected across a tap in the potential divider and the negative of the source. If a current of 4 A flows towards the load, what is the current supplied by the source? (Remember, a voltage divider is a network of resistors that are connected in series the purpose of which is to divide a voltage into each of the resistors.) Show complete solution.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l33.2AI4RT3.582R116R210R3R420PTP1P2P3P4
A charger, a battery and a load are connected in parallel. The voltage across the charger is 12.5 volts and the battery has an emf of 12 volts and the internal resistance of 0.1 ohm. The load of 2 ohms resistor. Find the current through the charger.
A charger , a battery and a load are connected in parallel. The voltage across the charger is 12.5 volts and the battery has an emf of 12 volts and internal resistance of 0.1 ohm. The load consists of a 2 ohms resistor. Find the current through the charger.
Find the value of open circuit voltage and looking back resistance
The diagram in the figure shows a simple circuit consisting of a battery and a load consisting of two resistors.The battery voltage is UB = 56 V and the value of the resistors is:R1 = 1800R2 = 5400a) The ammeters in the circuit show the following value:A1 shows valueA2 shows valueA3 shows valueb) In the load, the effect developsc) The total resistance of the load is
Which of the following is/are an accurate statement/s? A The potential in any closed loop is zero. B In parallel connection of two resistors, the current is higher for lower resistance. The voltage divider is used to find the potential across the resistors in parallel. The sum of current entering the junction is equal to the sum of potential in any closed loop.
Two batteries are connected in parallel delivering power to a power resistor. The first battery has an open circuit voltage of 12.6 V and an internal resistance of 0.2 ohm. The second battery has an open circuit voltage of 12.2 V and an internal resistance of 0.3 ohm. Find the maximum power delivered to the load resistance.
The full scale value is 20 Volt and it is required to measure a maximum of 1000 Volt with a voltmeter with an internal resistance of 500 kohm. What kind of resistance is needed to measure 1000V voltage with this 20V voltmeter, find out by calculating the value of this resistance. Should the resistance be connected in series or parallel to the voltmeter. Briefly explain the reason by drawing a figure.
.. Two resistances of 10 and 15 ohms, each respectively are connected in parallel. The two are then connected in series with a 5-ohm resistance. It is then connected across a 12-V battery. What are the current and power?
Which of the following statements regarding circuits are true? To find resistance in a parallel circuit, you must sum the individual resitances The direction of conventional current is the direction of positive charge flow. In a circuit, electrons flow from high potential energy (at the negative terminal) to low potential energy (at the positive terminal). When electricity is passed through a lightbulb, the electrons are 'used up' by the bulb. All voltages in a loop sum to 12V The current that flows into a resistor is the same as the current that flows out. To 'short circuit' something means there is an alternate path of less resistance for the current to flow. Switching on a light happens immediately because electrons move from the power source to the bulb incredibly quickly. A 'kilowatt-hour' is a unit of power, not energy.
INSTRUCTIONS: Solve the following problems. Show and COMPLETE solutions. Draw all CIRCUIT DIAGRAMS or the equivalent circuit (dummy circuit) as the case may be. Write your solutions on sheet/s of short bond paper. A battery is to consist of 20 identical cells. The emf of each cell is 1.5 V and the internal resistance is 0.20 ohm. This battery will be used to supply power to a 10 ohm lamp. Determine the current on the lamp if:1. The 20 cells are connected in series 2. The 20 cells are connected in parallel 3. The 20 cells are arranged 5 cells in series in 4 parallel rows.
To measure the change in resistance of the gage(s) and indicate the location of the gauge on the beam, construct the Wheatstone bridge circuit. Calculate the Wheatstone bridge output if the gauge indicates a strain of 4000.then,Evaluate how can the number of strain gauges affects your measurement result. Justify your response with a calculation and a diagram showing the gage's placement on the beam.