Use the References to access important values if needed for this question. A student weighs out a 1.87 g sample of MnCl₂, transfers it to a 100. mL volumetric flask, adds enough water to dissolve it and then adds water to the 100. mL tick mark. What is the molarity of manganese(II) chloride in the resulting solution? Molarity = M Submit Answer Try Another Version 7 item attempts remaining

Use the References to access important values if needed for this question. A student weighs out a 1.87 g sample of MnCl₂, transfers it to a 100. mL volumetric flask, adds enough water to dissolve it and then adds water to the 100. mL tick mark. What is the molarity of manganese(II) chloride in the resulting solution? Molarity = M Submit Answer Try Another Version 7 item attempts remaining

Introductory Chemistry: An Active Learning Approach

6th Edition

ISBN:9781305079250

Author:Mark S. Cracolice, Ed Peters

Publisher:Mark S. Cracolice, Ed Peters

Chapter16: Solutions

Section: Chapter Questions

Problem 38E: A student weighs out a 4.80-g sample of aluminum bromide, transfers it to a 100-mL volumetric flask,...

See similar textbooks

Similar questions

What is the difference between a solute and a solvent?
You wish to prepare 1 L of a 0.02-M potassium iodate solution. You require that the final concentration be within 1% of 0.02 M and that the concentration must be known accurately to the fourth decimal place. How would you prepare this solution? Specify the glassware you would use, the accuracy needed for the balance, and the ranges of acceptable masses of KIO3 that can be used.
It is stated in Section 6.3 of the text that to balance equations by inspection you start “with the most complicated molecule.” What does this mean? Why is it best to do this?
On Easter Sunday, April 3, 1983, nitric acid spilled from a tank car near downtown Denver, Colorado. The spill was neutralized with sodium carbonate: 2HNO3(aq)+Na2CO3(aq)2NaNO3(aq)+H2O(l)+CO2(g) a. Calculate H for this reaction. Approximately 2.0 104 gal nitric acid was spilled. Assume that the acid was an aqueous solution containing 70.0% HNO3 by mass with a density of 1.42 glcm3. What mass of sodium carbonate was required for complete neutralization of the spill, and what quantity of heat was evolved? (Hf for NaNO3(aq) = 467 kJ/mol) b. According to The Denver Post for April 4, 1983, authorities feared that dangerous air pollution might occur during the neutralization. Considering the magnitude of H, what was their major concern?
39. Standard solutions of calcium ion used to test for water hardness are prepared by dissolving pure calcium carbonate. CaCO3, in dilute hydrochloric acid. A 1.745-g sample of CaCO3 is placed in a 250.O-mL volumetric flask and dissolved in HCI. Then the solution is diluted to the calibration mark of the volumetric flask. Calculate the resulting molarity of calcium ion.
94. Baking soda (sodium hydrogen carbonate. NaHCO3) is often used to neutralize spills of acids on the benchtop in the laboratory. What mass of NaHCO3 would be needed to neutralize a spill consisting of 25.2 mL of 6.01 M hydrochloric acid solution?
On the basis of the general solubility rules given in Table 6-1, predict which of the following substances are likely to be soluble in water. a. zinc chloride b. lead(II) nitrate c. lead(II) sulfate d. sodium iodide e. cobalt(III) sulfide f. chromium(III) hydroxide g. magnesium carbonate h. ammonium carbonate
In the spectroscopic analysis of many substances, a series of standard solutions of known concentration are measured to generate a calibration curve. How would you prepare standard solutions containing 10.0, 25.0, 50.0, 75.0, and 100. ppm of copper from a commercially produced 1000.0-ppm solution? Assume each solution has a final volume of 100.0 mL. (See Exercise 123 for definitions.)
When 10. L of water is added to 3.0 L of 6.0 M H2SO4, what is the molarity of the resulting solution? Assume the volumes are additive.