Use Kirchhoff's law methodIndicates the conduction status of the diodeThe result is the table of current and voltage values foreach elementIncorporates the diode conduction voltage if applicable9)R1200Dzes; Rz10,ojesiEIE2E3

Answered: Image /qna-images/answer/bcb107d7-549f-4a17-b2fa-779498d510d4.jpg

Answered: Use Kirchhoff's law method Indicates…

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
What is CEMF?
Q2/ Consider the circuit in below figure. What type of circuit is this? b. What is the total peak secondary voltage? c. Find the peak voltage across each half of the secondary. d. Sketch the voltage waveform across RL. e. What is the peak current through each diode? f. What is the PIV for each diode? а. 4:1 D1 120 V rms RL 1.0 kN 00400
Consider the circuit in the figure below 4:1 120 V rms ooooo gll reelee D₁ L a. What type of circuit is this? b. What is the total peak secondary voltage? D₂ c. Find the peak voltage across each half of the secondary. d. Sketch the voltage waveform across RL. e. What is the peak current through each diode? f. What is the PIV for each diode? RL 1.0 ΚΩ
Question-1: Consider the circuit in Figure below. 1. What type of circuit is this? 2. What is the total peak secondary voltage? B. Find the peak voltage across each half of the secondary. 4. Sketch the output voltage waveform across R1. 5. Sketch the voltage through D1? 6. What is the PIV for each diode? 120 V rms D2
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
Determine the output waveform for the network of Figure. bellow and calculate the output dc level and the required PIV of each diode.? 10 V 2 kQ T t 2 2 k2 2 kN
Q1/Consider the circuit in Figure with a transformer of 10:1 transformation ratio and the diodes are silicon. a) What type of circuit is this? (b) What is the total peak secondary voltage? (c) Find the voltage value across the resistor (d) Sketch the voltage waveform across RL (e) What is the PIV for each diode? D3 D 120 V Pisez) Vpouo D D 10 kn lleee
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
USING D1 1N4001G or SILICON DIODE. To sketch the characteristic curve of the diode you need to vary voltages on diode and measure current flowing during forward and reverse bias condition. Fill up the table below using circuit shown and vary battery voltages. Measure voltage and current of diode then sketch the graph. Voltage X axis and Current Y axis. Battery Diode Diode Voltage Current Voltage Battery Diode voltage Voltage 0.1V 0.3V 0.5V 0.7V 1.0V 2.0V 3.0V 10.0V Diode Current Forward Bias Condition A V 0.1V 0.5V 2.0V 5.0V 10v 20V 25V 30V Reverse Bias Condition Note: used any electronics software to perform this activity
Q1 Assume that each diode has a turn-on voltage 0.7V in the circuit shown in Figure Q1. By using the constant voltage drop model: 1kN D1 D2 2kN 4k2 6V 3V 4V Figure Q1 a) Show that it is not possible that D1 is on and D2 is off. (Hint: show a contradiction) b) Show that both D1 and D2 are on.

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Use Kirchhoff's law method Indicates the conduction status of the diode The result is the table of current and voltage values for each element Incorporates the diode conduction voltage if applicable