(b) Two reservoirs are connected by a pipeline consisting of pipe 1, pipe 2, pipe 3 connected in series with length of 170 m, 300 m, 210 m respectively. The different in water surface levels in two reservoirs is 12 m. The friction coefficient for pipe 1, pipe 2 and pipe 3 are 0.0052, 0.005 and 0.0048 respectively. Based on Table 2 and the setting given, determine the flowrate of the flow if the entrance loss coefficient is 0.25 considering : (i) minor losses; and (ii) neglecting minor losses. Table 2: Setting of Question Setting Diameter (mm) Pipe 1 220 Pipe 2 320 Pipe 3 420 3

(b) Two reservoirs are connected by a pipeline consisting of pipe 1, pipe 2, pipe 3 connected in series with length of 170 m, 300 m, 210 m respectively. The different in water surface levels in two reservoirs is 12 m. The friction coefficient for pipe 1, pipe 2 and pipe 3 are 0.0052, 0.005 and 0.0048 respectively. Based on Table 2 and the setting given, determine the flowrate of the flow if the entrance loss coefficient is 0.25 considering : (i) minor losses; and (ii) neglecting minor losses. Table 2: Setting of Question Setting Diameter (mm) Pipe 1 220 Pipe 2 320 Pipe 3 420 3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1.28. The performance curve for the fan of Problem 1.27 can be approx- imated by a straight line through its BEP (using techniques devel- oped in Chapter 7). The curve is Aps = 4488 – 166Q, with ApT in Pa and Q in m³/s. If this fan is connected to a 1-m dia- meter duct (f = 0.045) whose length is 66 m, what flow rate will result? %3D
Q1. Two pumps with 105.4 cm in diameters characteristics shown in figure below are used in paralel to pump water to the system. Neglecting local losses, calculate total flow rate and pump power. (a) n= 710 d/dak 120 7.5 80m ENPY (2) 6. 105 - 105.4 cm çap S N 4.5 3 90 96.52 cm çap 88% 86% 75 - 88.9 cm çap S4% (1) bom 60 1100 kW 45 750 kW 30 0.25 0.50 0.75 1.00 1.25 1.50 1.75 Debi m/s Note: Pipe is cast iron with 0.6 m in diamater and 1.6 km in length. Fluid is water with density 1000 kg/m³ . ENPY m %68 900 kW
A closed tank 5m high contains 2.5 m of water. A nozzle 75 mm in diameter is installed at the side of the tank at a distance 0.5 m. from its bottom. Compute the required air pressure inside the tank to produce 10 hp energy at the nozzle. Cv = 0.95 and Cc = 0.62. * a. 234.65 kPa b. 151.88 kPa c. 183.31 kPa d. 121.23 kPa
In a 250 mm diameter pipe, oil discharges through a sharp crested round orifice, 100 mm in diameter. If the coefficient of contraction (Cc) and coefficient of velocity (Cv) are 0.63 and 0.98, respectively. SG of oil is 0.86. Determine the following: a) discharge from the orifice, (L/s) given that: coefficient of orifice, Co= Cc x Cv b) diameter of jet (mm) given that: Cc = Ajet/Atheo c) actual velocity in the jet, (ft/s) Note: Maintain 3 decimal places on partial and final answers.
A pump 254 mm suction pipe and a 127 mm discharge pipe is used to deliver 52 L/s of water. The suction gage reads 15.6 kPa vacuum and the discharge gage located 100 cm above the suction gage which reads reads 108 kPa gage. Determine the following: 1. The total dynamic head in meter 2. The water power in kW 3. The motor horsepower if the pump efficiency is 76% Choices: 1. 13.856 14. 495 14.409 2. 7.631 7.348 8. 245 3. 12.960 14.935 13.935
2. A storage contains liquid at depth y where y-0 when the tank is half full, as shown below. Liquid is withdrawn at a constant flow rate Q to meet demands. The contents are resupplied at a sinusoidal rate 3Qsin2(t). The storage tank has a diameter D=5m. a. Beginning from conservation of mass, formulate an equation for the change in dV TD2 depth of water as a function of time. Hint: dt din - 9out and V = 4 b. Use Euler's method to solve for the depth y, show the iterative equation for the Euler's method, and use Q=5 m3/s to complete the table below: t (s) y (m) 0.5 1.0
A pumping station wet well operates between 540- and 550-ft elevation. The pump curve is deϐined by the following points: 80 ft at zero ϐlow, 78 ft at 200 gpm, 65 ft at 800 gpm, and 50 ft at 1200 gpm. The pump discharge contains an equivalent of 50 ft of 6-in. pipe. The discharge pipe is 120-ft long and terminates at a splitter box, elevation 570. Using C=100, plot the pump curve and the corrected pump curve. Plot the pump discharge curves at each wet well elevation and for C=100 and C=140. What is the pump ϐlow at the low and high wet well elevations for newand old pipe?
Q1/ For fig shown if water flow rate is 60 lit/s , Find (h) Note that Density: Pwater = 1 kg/m Pair = 1 kg/m 3 D, = 5 00mm air Water 0.5 m Water O2 = 25cm 1)
dp 1. It shows that the behavior of fluid is A From the equation stated, show the formula for mass flow rate AVp = c. :C.
An irrigation line carries water from a lake down into an arid valley 810 ft below the surface of the lake. The water discharge through a nozzle with jet velocity of 220ft/s, the diameter of the jet is 4 in. Find the power loss in friction expressed in hp. (WITH FREE BODY DIAGRAM) CHOICES: A.127 B.120 C.158.45 D.187
49. Water flows at a rate of 200 GPM into a piping system connected in series. Length, diameter, and loss coefficient of each pipe are given below. For p= 62.4 Ibm/ft and u = 0.7E–3 lbm ft/s find total pressure drop and the diameter of an equivalent pipe representing this system. C) Fluid Power Theory an.. IndPitEn IlIb. Fluid Mechanics: Incompressible Viscous Flow 392 Pipe D K No. (ft) 100.00 (in) 5.00 (-) 50.00 1 2 80.00 4.50 45.00 3 70.00 4.00 65.00 4 120.00 3.50 55.00 5 90.00 3.00 15.00
Problem-4: The characteristics for a pump are given in the table below. The pump is required to left water against static head Az = EN" m. The pipe arrangement has a total length L the pump discharge, head, efficiency and power for the given pipe system. 200, d = 0.1 m and f= 0.016. Find %3D Q (L/s) 10 20 30 35 42 50 Hp (m) efficiency % 210 201 180 150 129 93 48 30 58 80 85 86 74 EN=62 Hp = Az + h, = Az + 12.1 d P = 757