Toluene is being stored in a 5 m diameter cylindrical tank under a pressure of 400 kPa (absolute). The tank drains through a 2 cm diameter line located 8 m below the liquid level of the tank, you can assume that the pressure at the outlet of this line is 1 atm. Toluene has a density of 870 kg m3 and a viscosity of 0.56 mPa s. Using Bernoulli's equation (or otherwise) estimate the liquid velocity in the drain line when the valve is opened, and hence determine how long it will take for the tank to drain. Comment as to whether or not you will think the tank will actually take more or less time to drain than the value you have calculated.

Toluene is being stored in a 5 m diameter cylindrical tank under a pressure of 400 kPa (absolute). The tank drains through a 2 cm diameter line located 8 m below the liquid level of the tank, you can assume that the pressure at the outlet of this line is 1 atm. Toluene has a density of 870 kg m3 and a viscosity of 0.56 mPa s. Using Bernoulli's equation (or otherwise) estimate the liquid velocity in the drain line when the valve is opened, and hence determine how long it will take for the tank to drain. Comment as to whether or not you will think the tank will actually take more or less time to drain than the value you have calculated.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For liquid viscosity measurement, it is desired to create a viscometer consisting of two 30 cm long concentric cylinders. The diameter of the inner cylinder is 20 cm and the diameter of the outer cylinder is 20.2 cm. Since a torque of 0.13 N cinsm is required to rotate the inner cylinder with an angular velocity of 40 rad / s, what will be the viscosity of the fluid in the viscometer in Pa⋅s? Take the value of as 3.
A steel ball with the density of 6324 kg/m and the radius of 0,48 cm was dropped into the oil whose viscosity was to be measured as is seen in the figure. When the ball attains a constant velocity, the distance that the ball travelled was measured as 97 cm within the time interval of 4 sec. Before the experiment, the mass of the 100 ml-oil was measured as 2,8 gr. According to the data given above, find; a) the density of the oil (in kg/m). (Please do not use any decimal digit.) Yanıt:
The tank of an air compressor has a volume of 2m3 and is filled with air at a temperature of 40 degrees C. If agauge pressure on the tank reads 7.5 bars,what is themass of the air in the tank?
What is the difference between dynamin and kinematic viscosity? That is the significance of these properties of liquid?
A steel ball with the density of 6229 kg/m and the radius of 0,65 cm was dropped into the oil whose viscosity was to be measured as isseen in the figure. When the ball attains a constant velocity, the distance that the ball travelled was measured as 99 cm within the time interval of 4,7 sec. Before the experiment, the mass of the 100 ml-oil was measured as 2,1 gr. According to the data given above, find; a) the density of the oil (in kg/m ). (Please do not use any decimal digit.) b) the speed of the steel ball after the ball attains a constant velocity (in m/s). (Please use 4 decimal digits.) c) the dynamic viscosity of the oil (in Pa.s) (Please use 3 decimal digits.) d) the flow Reynolds number. (Please use 4 decimal digits.) Please solve this question step by step to reach correct answers. correct answers: a) 21 b) 0,2106 c) 2,715 d) 0,0212
It is desired to determine the surface tension of a particular fluid using a capillary-riseexperiment. Kienth used a 0.5 mm glass tube and found that the height of the liquidmeasured 30 mm with a contact angle of 30°. Kienth then performed viscosity measurements using an Ostwald viscometer. He found that the fluid takes 1.5 times slowerto flow through the viscometer relative to water with a density of 1000 kg/m? and aviscosity of 1.0 cP. It is previously known that the viscosity of the fluid is 1.35 cP. Whatis the surface tension of the liquid?
The liquids are positioned as shown in an open tank with a square bottom figure bellow. Solve for the following if the “P atm = 101.325 kPa”.
A rotating viscometer consists of two concentric cylinders—a stationary inner cylinder of radius Ri and an outer cylinder of inside radius Ro rotating at angular velocity (rotation rate) vo. In the tiny gap between the two cylinders is the fluid whose viscosity (m) is to be measured. The length of the cylinders is L. L is large such that end effects are negligible (we can treat this as a two-dimensional problem). Torque (T) is required to rotate the inner cylinder at constant speed. Showing all your work and algebra, generate an approximate expression of T as a function of the other variables.
Fluid Properties-The difference in pressure between theinside and outside of a soap bubble wasobserved to be 1.6 N/m2. If the surfacetension of the liquid is 40 dyne/cm, what will be the diameter of the bubble in meters?
A vessel of capacity 3 m³ contains the mass of 7 kg of Oxygen gas at a pressure of 180000 N/m? and a temperature of 310 K. Find the gas constant of Oxygen gas in J/kgK. Gas constant, (J/kgK) =
An air bubble is observed from the bottom up to the water surface The atmospheric pressure is 101 325 kPa The volume of the bubble at the bottom is 1/7 times the volume of the bubble at the surface Determine the height of the water in meters.
On Mars, the atmosphere is composed mainly of carbon dioxide. The value of the gas constant for the Martian atmosphere is 192 J/kg K, and the acceleration of gravity there is 3.72 m/s?. At the average level of the Martian surface, the average temperature is 228 K, the pressure is 774 Pa, and the density is 0.01768 kg/m3. surface, the average temperature is 225 K. What are the pressure and density at this altitude? At an altitude of 1km above the