The stresses acting on element A on the web of a train rail (see part (a) of the figure) are found to be 50 MPa tension in the horizontal direction and 140 MPa compression in the vertical direction (see part (b) of the figure). |140 MPa B A | 50 MPa Cross Side 57 MPa View Section (а) (b) Also, shear stresses of magnitude 57 MPa act in the directions shown. Determine the stresses (in MPa) acting on an element oriented at a counterclockwise angle of 52° from the horizontal. (Use the sign convention for stresses acting on inclined sections. Round your answer for o to at least one decimal place.) Ox1 = MPa Oy1 = MPa Txıy1 MPa

The stresses acting on element A on the web of a train rail (see part (a) of the figure) are found to be 50 MPa tension in the horizontal direction and 140 MPa compression in the vertical direction (see part (b) of the figure). |140 MPa B A | 50 MPa Cross Side 57 MPa View Section (а) (b) Also, shear stresses of magnitude 57 MPa act in the directions shown. Determine the stresses (in MPa) acting on an element oriented at a counterclockwise angle of 52° from the horizontal. (Use the sign convention for stresses acting on inclined sections. Round your answer for o to at least one decimal place.) Ox1 = MPa Oy1 = MPa Txıy1 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An element in plane stress on the fuselage ofan airplane (figure part a) is subjected to compressivestresses with a magnitude of 42 MPa in the horizontaldirection and tensile stresses with a magnitude of9.5 MPa in the vertical direction (see figure part b).Also, shear stresses with a magnitude of 15.5 MPa actin the directions shown.Determine the stresses acting on an element orientedat a clockwise angle of 40° from the horizontal.Show these stresses on a sketch of an element orientedat this angle.
Refer to figure STR - 5 Two prismatic bars are rigidly fastened together and support a vertical load of 45kN. The upper bar is of steel having mass density 7750 kg/m^3 , length 10m and cross-sectional area 65 cm^2. The lower bar is of brass having mass density 9000kg/m^3, length 6m and cross-sectional area 50 cm^2. Determine the maximum stress in each material. For steel Es= 200 GN/m^2 and for brass Eb= 100 GN/m^2. I need answer ASAP. Thank you!
es A state of stress at a point is the result of two separate actions; one produces the pure shear of 35 MPa shown in figure A and the other produces the pure shear of 30 MPa shown in figure B. 35 MPa -19.86 degrees Y -17.04 degrees -X Figure A Which of the following most nearly gives the principal planes for the combined state of stress? Select the correct response: 35 MPa 30° Figure B 30 MPa 30 MPa 4
Question: The member shown in figure has a rectangular cross section. Determine the state of stress that the loading produces at point K. 30° 1 m F = 80 kN K a 180 mm 200 mm 100 mm 1,5 m 2 m 3 m Section a-a
Determine the total strain in the bar shown in Figure 2. 3 go AE Lineal
Q36 onlys Ratio of stress in part A and B
Q 2: The state of stress at a point is characterized by the components: Ox Txy Txz [12 3 Tyx Oy Tyz = 4 [Tzx Tzy Oz 0 10. Find the values of the principal stresses and their directions?
Q1 A truss system is shown in Figure Q1. It is loaded at joints D and E as shown. The truss members are to be manufactured from Aluminium Alloy cylindrical bar with a tensile yield stress of 300 MPa, a compressive yield stress of 200 MPa, and Young's Modulus of 70 GPa. 1.5m 1.5m A B 4001 10 KN 3m Fig. Q1 E 水 20 KN 1.5m D ➜ (a) Show that the truss system can be described as statically determinate. (b) Draw a Free Body Diagram of the truss and determine the reactions at the supports. (c) Use the METHOD OF JOINTS to determine the load in each member of the truss, indicating whether they are tensile or compressive.
Q.41 For the state of stresses (in MPa) shown in the figure below, the maximum shear stress (in MPa) is 2 44 4 4 4 2
The normal and shear stresses acting on element A are 6,650 psi, 17,600 psi, and 2,700 psi (see part (b) of the figure below). (Consider only the in-plane stresses - the stresses in the xy-plane). 117,600 psi B A 6,650 psi A Cross Side |2,700 psi Section View (a) (b) Determine the maximum shear stresses (in psi), associated normal stresses (in psi), and angles of the principle planes (in degrees counterclockwise from the +x-axis). (For maximum shear stress, enter the magnitude. For normal stresses, use the sign convention for stresses acting on inclined sections.) max = psi psi 02 psi %3D ° counterclockwise from the +x-axis p1 p2 ° counterclockwise from the +x-axis
3. A punch for making holes in steel plates is shown in Fig. a. Assume that a punch having a diameter of 19 mm is used to punch a hole in a 6-mm plate, as shown in the cross-sectional view (see figure (b)). If a force P=125kN is required, what is the average shear stress in the plate and the average compressive stress in the punch? (b) (a)
3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 13.05 ksi, or in bronze of 100 MPа. Aluminum A = 400 mm? Bronze A = 200 mm Steel A = 500 mm? 2P 4D 2.5 m 2.0 m 1.5 m